Washer Bearing Parts

Supports washer drum for smooth, quiet rotation during spin cycles. Replace if you hear grinding noise or excessive vibration. Verify fit with your model.

This bearing housing assembly supports the washer tub and secures the inner bearing for smooth drum rotation. Replaces worn or damaged upper housing to reduce noise and restore stable tub alignment. What it does:

• Holds the upper bearing and anchors the inner tub to the transmission/drum shaft.
• Maintains correct tub alignment to prevent excessive wobble or vibration during spin.
• Keeps the bearing seated to reduce grinding, squealing, or rumbling noises.
• Helps prevent premature bearing wear that can lead to louder operation or tub movement.

• One upper bearing housing assembly.

• Disconnect power and water supply before beginning service; follow all safety precautions.
• Drain and support the tub before removing fasteners; this may require disassembling the cabinet and removing the agitator/tub per the service manual.
• Inspect bearings and seals when replacing the housing; replace any worn bearings or seals to ensure proper function.

This bearing supports the spin basket (inner tub) in top-load washers, allowing it to rotate smoothly during the spin cycle. It is mounted at the base of the spin basket and bears the load of the drum and its contents. Replace this bearing if the washer makes loud grinding or squealing noises during the spin cycle, if the basket wobbles excessively, or if you notice water leaking from beneath the tub.

This is a small bearing that fits into the right-side lid hinge on a top-load washer, allowing the lid to pivot open and closed smoothly. It reduces friction and wear on the hinge assembly. Replace this bearing if the lid feels stiff, wobbly, or makes grinding or squeaking noises when opening or closing.

Replace this washer hub and seal kit when you notice water leaking from the center shaft or loud noises during spin cycle. Confirm fit with your model.

NOTE: No longer includes the Drive and Bell Kit 39508P

The OEM Replacement is a bearing designed to function as the rear bearing in Whirlpool front-load washers. It also works as the upper brake bearing in top-load washers. Positioned near the tub's brake assembly, this component plays a significant role in the operation of the washer. In top-load washers, it resides above the brake assembly.

Causes of a bad bearing can include prolonged wear and tear, exposure to excessive loads, or water intrusion that leads to rust and corrosion. A compromised bearing can lead to more significant issues if not addressed promptly.

Symptoms of a bad bearing include:

• Loud, unusual noises during the wash or spin cycles
• Excessive vibration or movement of the washer
• The drum not rotating smoothly or becoming stuck
• Leaks around the drum area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replace worn washer tub bearings when you hear grinding noise or smell burning rubber during spin cycles. Prevents drum friction and damage. Verify fit.

This small hardware washer sits under a fastener in the specified assembly to distribute load and maintain proper spacing. Replacing a worn or missing washer helps keep components tight, aligned, and operating smoothly.

• Distributes clamping force to prevent fastener pull-through and damage
• Maintains correct spacing/stack-up in the original assembly
• Helps reduce loosening, vibration, and premature wear at the joint
• Typical signs of trouble include rattling, looseness, or misalignment at the connection point

• Disconnect power (and turn off water supply if accessing a wet area)
• Use your model's parts diagram to locate and install the washer
• Replace one-for-one; reinstall any spacers or clips in the same stack sequence
• Tighten fasteners to manufacturer guidance—do not overtighten

The Bearing Ball is an OEM part for LG washing machines. It is a critical component in the washer's drum assembly, ensuring smooth and efficient rotation during wash cycles. The bearing reduces friction between moving parts, which helps in maintaining the washer's performance and longevity.

Causes of a bad bearing ball can include normal wear and tear over time, heavy usage, exposure to excessive loads, or contamination with debris and moisture. A faulty bearing can lead to decreased efficiency and potential damage to other components.

Symptoms of a bad bearing ball include:

• Loud, grinding, or rumbling noises during operation
• The drum wobbling or moving unevenly
• Water leaks from the drum area
• Reduced efficiency in the spin cycle

This OEM LG part is also compatible with Sears/Kenmore.

Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.

Washer bearing supports drum rotation during spin cycles. Replace if washer makes loud grinding or squealing noises. Verify fit with your model number.

Supports the washer transmission shaft to reduce axial wear and noise. Replace when you hear grinding sounds or experience rough operation. Confirm fit with your model number.

Washer bearing supports the drum during spin cycles. Replace if you hear grinding noises or excessive vibration. Confirm fit with your model number.

Cushions and spaces the transmission-tub interface to reduce wear and maintain smooth spin. Replace if you notice abnormal noise or vibration. Confirm fit.