Whirlpool Parts

• Lid or door won't close
• Won't start

Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more

• Not dispensing water

I watched the Appliance Parts Pros repair video and decided to remove the front panel to diagnose the problem. While the repair video is excellent, I could not remove the ice/water dispenser front panel with a putty knife. On my model, 106.56234400, there is no clip that can be released by sliding a putty knife up under the front panel. It took a little effort but I was able to pop the left lower corner clip just by pulling it out with my fingers. Once the cover was off I could see that the... Read more

• Ice maker dispenses too little ice
• Ice maker dispenses too much ice
• Ice maker won't dispense ice
• Ice maker not making ice

Replace assembly Read more

It was a classic horror story, but with a happy ending! I called a classic, "regular" repair company that I obtained on-line. My Whirlpool was 2 months out of warranty, so the repairman charged a trip-fee of $95 that would be subtracted from the cost of my repair. "Lee" showed up an hour late, even though he was told that I had to leave for work by 10:30 (-He assured me that he would have me fixed by then). The refrigerator was rolled out of its spot, and Lee began to remove the back cover... Read more

Found the correct replacement in your easy to navigate parts lookup, ordered part, arrived sooner than I expected, Needed a nut driver to remove old part, unplugged harness, plugged new part in , retightened three screws and began making ice. Very clean and simple process. Thanks guys, I couldn't have done it with out you Read more

Took broken bin out and replaced with new one. No tools were required ( for the next section since it won't allow me to only select other). Read more

Installed new agitator Read more

Watched the attached video, then followed directions and installed the part ordered. Read more

The original pump was getting jammed intermittently, more and more often. I cleaned it out, but that didn't help the jamming. So I ordered a new pump. Have your new pump on hand and look at it to see how it attaches. The original pump, a different part number than the replacement, lasted about 7 years of almost everyday use, with multiple loads each day. My washer model Maytag MHW5500FW0 has the pump at the bottom back, in an awkward position. This took me about 2 hours due to the awkward... Read more

• Door sweating
• Door won't open or close
• Clicking sound
• Fridge too warm

Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more

• Fridge runs too long
• Freezer not defrosting
• Freezer too cold
• Won't start

A bit of research on the internet indicated the most likely problem was with the defrost system. I found the service manual for the refrigerator and was able to determine that the defrost heater and thermostat passed the self test. The refrigerator would perform a forced defrost which resulted in a cold refrigerator. More research revealed that this particular refrigerator does not have a defrost timer, instead the defrost cycle is controlled via the Electronic Control board which is also... Read more

• Fridge too cold
• Fridge runs too long
• Won't start
• Freezer section too warm

The 20 year old unit still serves us well, looks good and has been kept in good repair. The condenser fan had stopped so I removed, cleaned and oiled that motor. The decision was made to make an upgrade to the evaporator motor and control units so that the appliance could reasonably be expected to have extended service life. The Ice maker module had been replaced 7 years ago. I ordered the parts and have made the upgrade for temperature controller and the defrost control. If you are in a... Read more

After about 6 months of use with our Whirlpool Cabrio washing machine it started to sound extremely loud in the spin cycle, we should have called Whirlpool at this point to have it looked at under warranty. Fast forward 5 years later our loud washing machine ended up leaking out the bottom, we had a local service company come out to take a look at doing the repair and they quoted $800 to replace the outer tub assembly. I was not going to pay $800 and figured that most likely we would purchase a... Read more

• No heat or not enough heat
• Takes too long to dry

Our 25-year-old Whirlpool dryer abruptly stopped producing heat, though it was otherwise running normally. The unit had never required service of any type and we were reluctant to replace it. After confirming that no circuit breakers had tripped, I reviewed the Whirlpool and AppliancePartsPro websites and concluded that the most likely causes of the problem were a failed heating element and/or thermal fuse. I ordered both (they arrived in two business days), installed them and the dryer... Read more

• Marks left on clothes

Maytag Gas Dryer Model: MGDE300VW1 I had previous experience with repairing my dryers, but this was a first for this model. Instructional videos very helpful. Ordered necessary parts and they were delivered with-in two days. Wow! Squeak found to be coming from idler pulley roller which no longer turned freely . The four other cabinet rollers had signs of wear. Dryer belt had frayed edges and a couple of burn spots in the belt from the motor turning before the drum did. Cleaned up all shafts... Read more

The part went on easily. U Tube video answered any questions I had before installing. Read more