Burner & Related Parts

Converting your gas dryer from natural gas to liquid propane? This LP conversion kit modifies the fuel orifice and components. Typical install: 1 hour.

Small metal cap that sits on the center of your gas cooktop burner head to direct and shape the flame. Replace if damaged, cracked, or missing.

This valve assembly controls incoming water flow to the appliance, restoring correct fill and preventing overfill or no-fill conditions when the original valve fails. It's a direct-replacement style part for affected units. What it does:

• Opens and closes to admit water during fill cycles so the appliance gets the correct amount of water
• Prevents continuous flow when closed, stopping overfills and leaks
• Helps resolve symptoms like no water fill, slow or weak filling, continuous water flow, or related fill/flood error codes
• Works with existing supply lines and mounting points when the original valve is removed

• Disconnect power and shut off the water supply before beginning service
• Drain remaining water from the appliance and have towels ready to catch drips
• Replace the old valve, reattach supply hoses and electrical connectors securely, and tighten fittings to OEM torque recommendations
• After installation, restore power and water, run a test cycle, and inspect all connections for leaks

LP conversion kit for gas cooktops. Includes orifices to convert natural gas cooktops to liquid propane fuel. Replace when switching fuel types.

Burner cap sits atop each surface burner on gas ranges and cooktops. Replace if cracked, chipped, warped, or missing to restore proper flame distribution.

LP conversion kit for gas ranges and cooktops. Converts natural gas appliances to liquid propane. Includes orifices and hardware for burner conversion.

Fix a dryer that won't heat or has a weak flame with this gas burner orifice. Controls proper fuel flow for consistent heating. Direct replacement part.

This burner base supports the cooktop's burner cap and directs flame for even heating. It replaces a damaged or warped base to restore stable burner alignment and consistent flame pattern. What it does:

• Holds the burner cap in place and centers the gas flame
• Channels gas flow for proper burner operation
• Helps prevent wobbling or uneven heating from a warped base
• Commonly replaced when the base is cracked, corroded, or bent

• One burner base (B)

• Turn off gas supply and power to the appliance before servicing
• Remove surrounding burner components and reassemble in reverse order
• Inspect nearby seals and burner ports for damage; replace if necessary

Rounded cap that sits over your gas cooktop burner to contain and direct flames. Replace if cracked, chipped, warped, or worn from high heat exposure.

Black burner cap assembly that covers and protects the gas burner head. Replace if your cap is cracked, chipped, damaged, or missing to restore appearance.

This cooktop is the main top panel for gas units. It supports the burners and grates, helps contain spills, and restores a clean, safe cooking surface when the original top is chipped, dented, or corroded.

• Serves as the primary surface where burner heads, caps, electrodes, and grates mount
• Contains spills and shields internal components from heat and debris
• Restores proper fit if grates or burners no longer sit level
• Typical reasons to replace include chips, cracks, warping, severe staining, or rust

• Disconnect power and shut off the gas supply before servicing
• Remove grates, caps, and burner heads; note screw locations and igniter lead routing
• Lift off the old top and transfer any brackets, grommets, or insulation as required
• Reassemble carefully and perform a leak check at burner connections after installation

Covers and protects the gas burner head on your range cooktop. Replace if cracked, chipped, worn, or missing to restore proper burner appearance.

Secures the surface burner assembly and positions the burner head for stable cookware support. Replace if cracked, broken, or damaged to restore alignment.

Burner cap sits over the gas burner head to focus and distribute flame evenly. Replace if missing, chipped, cracked, or warped to restore proper ignition.

The Water Valve is an OEM part for GE electric dryers. Located near the bottom of the machine, it controls water flow into the condenser system during moisture-sensing cycles.

The moisture sensing function uses this valve to introduce precise amounts of water vapor into the exhaust air stream periodically. This allows the condenser to capture moisture readings accurately and determine optimal cycle time based on humidity levels. 

Causes of failure include mineral buildup restricting flow, worn seals enabling leaks, or misaligned internal components hindering valve movement.

Symptoms of a faulty water valve are: 

• Loss of moisture sensing ability
• Incomplete or improper readings affecting cycle times  
• Water leaks from the valve area
• Failure to inject water vapor as needed

This part is also compatible with some Kenmore models using GE components.

Includes spark electrode.