Need Help?
Call
This is a gas safety valve that controls the flow of gas to the oven burner. It works in conjunction with the oven igniter - when the igniter reaches the proper temperature, the safety valve opens to allow gas to flow and ignite. Replace this valve if your oven does not heat, the igniter glows but gas never flows to the burner, or you smell gas when the oven is turned off.
Replaced the old valve with a new one from AppliancePartsPros.com. I watched one of the YouTube videos to get an idea of what the process would entail. I gathered the tools I would require, plus a work light. The repair/replacement went pretty good. One thing the video I watched didn't cover was adjusting the valve for a propane system. I compared my old valve to the new one and saw that I would have to screw down the oven gas outlet until it "bottomed out". Read more
Converting dryer from LP to natural gas? This gas orifice regulates gas flow to the burner for proper heating. DIY-friendly swap, takes 20 minutes.
Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more
Regulates gas flow to surface burners on gas ranges. Replace if bent, broken, cracked, or leaking. Located beneath burner caps on the cooktop surface.
We replaced both front orifice holders. Very easy to bend and break. If it has a deep bend in it, It will slow down the gas flow to the burner. if you have a low gas flow your burner will burn low So check your small silver gas lines and if you smell gas check your lines Read more
Replacement top burner for gas ranges. Installs on the cooktop surface to provide flame for cooking. Order if your burner is rusted, eroded, or broken.
We took the old ones off and put the new ones on..it was easy to do ..I want to say that the girl (I think her name was Heidi) she was a big help ,she made sure that I had the right parts,I ask her to show me the picture to make sure that they look like the part ..She was a really big help. I did a survey when I ordered the parts to..Thank you for your help and the parts Anna P Read more
The Burner, Large V2 is an OEM part for GE gas ranges. It is designed to provide a consistent and even flame for cooking, ensuring efficient heat distribution for large pots and pans.
Causes of a bad burner can include clogging from food spills, wear and tear from frequent use, or damage from cleaning processes. A malfunctioning burner can lead to uneven cooking and reduced heating efficiency.
Symptoms of a bad burner include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Remove and replace Read more
Replace this ignitor orifice assembly if the electrode is cracked, broken, or worn. Installs on gas range surface burners to restore spark ignition.
Installed a new ignitor/orifice assembly. Read more
This complete valve system controls gas flow to your dryer's heating element, regulating flame size and heat output. It opens and closes automatically based on temperature settings and safety requirements. Replace if your dryer won't heat, overheats, or you smell gas during operation.
Unfortunately my first repair attempt (replacing the Gas Valve Coils) failed so I decided to replace the entire Burner assembly. From a cost/time point of view the Burner assembly is a better value than just buying the Gas Valve seeing as you don't have to disassemble/reassemble most of the existing Burner (to get to the Gas Valve) *and* you get a new Igniter!! The most annoying thing about the repair is accessing the screw that clamps the gas pipe to loosen it :-(... Read more
Converting your dryer from natural gas to propane? This LP conversion kit includes calibrated orifices for proper fuel flow. DIY-friendly install.
Removing cabinet panels to access burner was the major challenge since every one seems to be different. This one, two screws at back allowed top to raise and be removed, Two more screws at front and two cables disconnected removed control panel. The door panel was not quite as obvious, The two screws at top sides and two at very bottom edge were removed. Then by trial, I removed screws around door edge until panel was loose. I removed a couple extra; but the whole door and panel lifted off.... Read more
Outer burner cap for sealed gas cooktop burners. Shapes flame distribution around the outer ring. Replace if cracked, warped, or missing.
Replaced burner assembly Read more
This is a replacement sealed burner cap. This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. This part is intended to replace a broken, misplaced, or defective burner cap in various models of gas ranges and stoves. Electrodes are included.This sealed burner cap protects the surface burner and allows the cooktop to light properly. If the gas igniter is glowing but does not ignite, the stove won't start up, or there will be a gas smell. Proper tools may be required to replace this part. Always ensure the appropriate safety precautions are adhered to when attempting to fix any appliances. Make sure that the stove is entirely disconnected from gas and power before starting the repair work. For more accurate information on how and where to install this sealed burner cap, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this burner cap is suitable for use on several different models of gas stoves, ranges, and cooktops manufactured by Whirlpool, Maytag, KitchenAid, Amana, and other Whirlpool brands. This is a genuine part made of high-quality, durable materials and is sold individually.
These are very easy to replace ,just gave the old one a quarter turn lifted it out took the two wires off (noted where each one will go on the new burner ) pop the wires onto the new burner put it on and good to go. Read more
The LP Bake and Broil Kit is an OEM replacement part for Whirlpool ranges. It is a kit containing everything needed to convert the oven from Natural gas to LP. Causes of a bad bake/broil system can include cracks, leaks, or corrosion in gas lines that produce unsafe flames over time. Pilot lights may fail to light consistently. Symptoms of failures include:
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.
I purchased a burner and a oven orifice replacement kit from Appliance Parts Pros. I downloaded an installation manual from Whirlpool and followed the instructions. It was pretty easy. The front burner orifices could be replaced by just taking off the burner cover. The back ones required removing the burner diffuser. You will need to reattach the back burner bottom assembies after you remove the diffuser before you unscrew the orifice or it might bend the burner piping causing it to not line up... Read more
Oven won't ignite or clicks but doesn't light? This bake burner with spark igniter fixes grounding issues and ignition failures. Easy DIY repair.
Replaced igniter under oven floor panel. Read more
Black burner cap sits on top of the burner head to distribute flame evenly. Replace if cracked, chipped, missing, or discolored from heat and spills.
These guys had exactly the parts I needed. We're quite expensive, but they arrived quickly and were a perfect fit! Read more
Replaces a cracked, corroded, or damaged burner on your gas range or cooktop. Installs on top to restore the heat source for your cooking zone.
Replaced burner with new. Did the trick. Works like new. Read more
Replacement burner cap for gas ranges. Covers the burner head and distributes heat evenly. Order a new cap if yours is cracked, faded, or missing.
Ordered new/replacements, excellent chat on line, Quick turn around delivery. Thank you Will recommend to friends. Read more
If your dryer won't heat or flame won't stay lit, a corroded burner tube may be the cause. This assembly includes an adjustable air shutter for proper combustion.
I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.