Cooktop Parts

It was a very quick repair that took less than 5 minutes to fix. Read more

Got new metal knobs, so much better! Read more

I ordered both hinges (if the nylon roller was bad on the left, it was probably going to go bad on the right side as well). The web site was easy to navigate, order process simple. Hinges arrived quickly. Slide the oven door up and off. unscrew the three screws for the hinge. You need to then pull up with some force (there is a big spring in there), and twist the hinge to get the last bit out. I used a hemostat to hold the spring and keep it from falling back into the hole. removed the... Read more

The previous tenant in my daughter's new apartment apparently had a grease fire of sorts in the GE XL44 gas oven. This left the insulating double glass panes so fouled up that one could not see into the oven. I removed the oven door (just lifts off the hinges) and proceeded to disassemble the door so as to get to the glass panes. That's when the real problems arose: the window seal rope, which lays around the edge of the opening to the oven, was burnt to a crisp -- see photos. The oven... Read more

I found the model and serial #'s. Looked them up on your website. You provided a diagram with part numbers. I ordered the parts. Your website made it extremely easy. Thank you. Read more

Initially, I took it off, sanded it and painted with appliance touch-up. Still didn't look good so I ordered a replacement part and installed. Read more

After checking all connections to ensure power was getting to element. I ordered new control board and replaced it myself. Saved about $100.00 on a service call for someone to come out and replace it Read more

First temp probe,then control board Read more

Knowing the odds of 2 failures occurring at the same exact time was unusually high, I just searched your site for what other broken items might affect these two failures. Came up with next control item upstream and tallied that item failure with percentages of successful repairs, (4 mins.) door safety switch. Since I had to change out the most likely of the 3 and since I was already was going to be into the switch panel I ordered all 3 and swapped them all out to cover my butt, as they were... Read more

Refer to Mynor T. of Draper, UT Aug. 12, 2018 write-up. I benefited greatly from the above write-up. It took me a little less time to perform this repair (excluding cleaning the assembly) due to the write-up. This GE Profile gas burner cook top is a “drop-in” model meant to be installed into counter top cut outs. The glass top edges are the actual support area for the entire cook top assembly. The burner bases (on top of the glass top) are screwed to the metal case enclosure (located beneath... Read more

• Element will not heat

This repair was on a GE glass Cooktop range. This range has two indicator lights, a Burner On light, and a Hot Cooktop Light. The problem I was having was, the Hot Cooktop stayed on all the time (24x7), even when the cooktop surface had been off for hours and was cold. YouTubes that I viewed were all misleading on this symptom. They all pointed to the switch, which is the fix for the Burner Light staying on, not the Hot Cooktop Light staying on. I figured it out by going to the schematic.... Read more

We bought replacements which fit very well and the burner elements are level again! Read more

Replace dual infinity switch. The only difficulty is the terminal labels on the new switch did not match at all with the terminal labels on the original switch. The enclosed instructions were NOT helpful. But I contacted your representative, Johnny, and he was most helpful and patient. From my model number he located very specific and detailed instructions for how to wire the new switch. The rest of the job was easy. Your representative was outstanding. Thanks. Read more

I googled the error code and symptoms my oven was exhibiting to determine the solution and which parts to order. I needed a new control panel and chose also to replace the overlay that shows on the front of the stove. I could have reused the old one because I turned out to be able to remove it without damaging it. I just kept it in case I damage the new one in the future. The “fast” shipping (not overnight) option had the part delivered the next morning, which was a nice surprise. I felt... Read more

• Won't start

Did some research to find out it was the electrode. Pulled out the old one to match what was on your site. It came in no time at all, and the replacement was a cinch. Read more

Installed new switches. Done in 20 minutes. Read more