Dishwasher Dispenser Parts

This wet agent dispenser replaces the washer's liquid fabric softener dispenser to restore proper dispensing during the rinse cycle. It helps keep softener contained until the machine is ready to release it, improving rinse-time performance. What it does:

• Holds and releases liquid fabric softener (wet agent) into the rinse cycle
• Ensures softener is delivered at the correct time for even distribution
• Stops leaking or premature release when the dispenser housing is intact
• Commonly replaced when the dispenser cracks, clogs, or fails to dispense

• Disconnect power to the appliance before starting any repairs
• Access method varies by model; remove dispenser drawer or top panel per your model's service instructions
• Inspect surrounding seals and clips; replace if damaged to prevent leaks

The Detergent Dispenser is an OEM part for Frigidaire dishwashers. It holds and releases detergent at just the right time during the dishwashing cycle to ensure all dishes and cookware are thoroughly cleaned. Located inside the dishwasher's control panel area, the detergent dispenser opens automatically to distribute detergent.

Causes of a bad dispenser can include buildup that clogs the release mechanism over time, broken components that prevent the door from opening fully, or damage from excessive force or impact.

Symptoms of a bad dispenser include:

• Detergent not dispensing or only partially dispensing during cycles
• Residue left inside the dispenser after washing
• The dispenser door sticking or failing to open as designed

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This wet agent dispenser assembly holds and releases liquid wetting/conditioning agents into the wash at the correct cycle, helping deliver fabric conditioner or similar additives when needed. It replaces a worn, clogged, or damaged dispenser for reliable delivery. What it does:

• Holds liquid fabric conditioner/wetting agent and releases it into the tub during the rinse cycle
• Ensures timed dispensing so conditioners are added at the proper point in the cycle
• Helps prevent over-dispensing and visible residue in the washer tub or on clothes
• Commonly replaces dispensers that leak, fail to release liquid, or have broken mounting tabs

• One wet agent dispenser assembly

• Disconnect power to the appliance before beginning any work
• Remove and reinstall using basic hand tools
• Rinse any remaining liquid from the area and avoid skin/eye contact with chemicals
• Test a short cycle after installation to ensure proper dispensing and secure mounting

A small replacement retainer clip used to secure exterior trim and interior panels on compatible Whirlpool appliances. Restores proper panel fit and prevents rattling or loose trim for a cleaner, safer operation. What it does

• Secures trim, panels or components in place to maintain proper alignment
• Helps stop rattling, vibration noise and loose-fitting parts
• Keeps seals and covers positioned so doors and panels close correctly
• Simple, single-purpose hardware used where a clip-style fastener is required

• One retainer clip as pictured

• Disconnect power (and water if applicable) before starting any repair
• Remove the surrounding trim or panel to access the retainer; small trim tools may help
• Fasten clip into the OEM mounting hole until it snaps or seats firmly
• Keep removed screws and small parts organized to avoid lost hardware

This dispenser door housing replaces a cracked or damaged refrigerator dispenser assembly to restore proper dispensing and appearance. It keeps the dispenser area sealed and supports the dispenser lever and chute. What it does:

• Provides the housing and mounting for the refrigerator dispenser assembly and lever
• Restores a secure chute to prevent leaks and keep dispensed water/ice directed into glasses
• Stops issues caused by cracked or broken dispenser housing, such as moisture inside the door
• Supports proper alignment of the dispenser lever and actuator components

• Disconnect power to the appliance before starting any repair
• Remove the inner door liner or access panel to access dispenser mounting screws; keep track of fasteners
• Inspect related gaskets and dispenser components for wear and replace if damaged

Also order retainer part number WP3400918

The Detergent Dispenser is an OEM part for Frigidaire dishwashers. It dispenses the necessary doses of detergent at precisely timed intervals during cycle operation. 

Causes of dispenser malfunction stem from normal wear over extended use. Mineral buildup can accumulate inside inhibiting proper dispensing action. Mechanical or electronic components controlling release functions are also susceptible to failure.

Symptoms of a bad dispenser include:

• Dishes not getting completely clean after cycles
• Residual food or film left on dishware   
• Error codes related to detergent supply issues
• Leaks or spills from the dispenser area

This OEM Frigidaire part is also compatible with some Electrolux, Gibson, and Kenmore appliance models. 

This dishwasher detergent and rinse aid dispenser stores detergent and releases it at the correct point in the cycle while metering rinse aid. Replacing a worn dispenser restores consistent soap release, cleaning performance, and spot-reducing rinse aid delivery.

• Holds detergent and rinse aid and seals to the inner door
• Opens the detergent cup at the programmed time during the wash
• Meters rinse aid into the final rinse to help reduce spotting
• Typical symptoms: detergent left in cup, dispenser door won't open, rinse aid not dispensing, or leaks around the dispenser area

• Disconnect power to the dishwasher before servicing
• Access from the inner door by removing the perimeter screws to separate the door panels
• Disconnect the wire harness, release the locking tabs, seat the new dispenser evenly, and tighten screws evenly to compress the seal
• Run a short cycle to check for leaks

This dispenser is the front housing that channels ice and water from the refrigerator to the user, restoring proper dispensing and a finished appearance. It fits into the refrigerator door and works with the dispenser controls. What it does:

• Directs and channels ice and water from the internal supply to the exterior dispenser opening
• Provides the mounting surface and openings for dispenser controls, actuator/lever, and chute
• Helps prevent leaks and misdirected water when the dispenser is working correctly
• Commonly replaced for cracked housing, broken mounting tabs, or cosmetic damage that affects dispensing

• One dispenser housing assembly

• Disconnect power and turn off the water supply before starting any repair
• Handle plastic clips and tabs carefully during removal to avoid breakage
• Reuse any electronic components only if compatible; replace damaged clips or seals
• After installation, turn on water and power and check for proper operation and leaks

The Tank is an OEM part for Whirlpool washing machines. It properly dispenses detergent during the wash cycle.

Causes of a bad detergent tank can include: cracks, holes or other damage that cause leakage or improper detergent dispensing. Scaling or mineral buildup inside the tank over time may also lead to detergent dispensing issues.

Symptoms of a bad detergent tank include:

• Detergent not being fully dispensed or released during the wash
• Residue or leftover detergent remaining in the tank after cycles
• Clothes not getting properly cleaned due to insufficient detergent release

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Detergent Dispenser is an OEM replacement part for Bosch dishwashers. It is located inside the dishwasher and is responsible for properly delivering detergent at the appropriate time during wash cycles. The detergent dispenser has a compartment that holds detergent tablets or pods, and a mechanism that releases the correct amount to efficiently clean dishes.

Causes of a bad dispenser can include clogging or blockage in the dispenser mechanism, damage to the dispenser door or latch, or malfunctioning electronic components that control the dispensing process.

Symptoms of a bad detergent dispenser include:

• Detergent not dispensing or residue left in the dispenser
• Dirty dishes due to insufficient or improper detergent delivery
• Corrosion or buildup inside the dispenser area
• Dispenser door or cover cracked or damaged

This genuine Bosch OEM replacement part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Detergent Dispenser Assembly is an OEM part for Whirlpool dishwashers, designed to store and release detergent and rinse aid at the appropriate times during the wash cycle. This component ensures that your dishes are cleaned efficiently by dispensing the correct amount of detergent for optimal washing performance. 

Causes of a malfunctioning dispenser can include mechanical failure of the latch or spring mechanism, clogging due to detergent buildup, or electrical issues preventing the dispenser from operating correctly.

Symptoms of a bad Detergent Dispenser Assembly include:

• Detergent not being dispensed correctly, leading to poorly cleaned dishes.
• The dispenser door not opening during the cycle or failing to latch properly before starting.
• Leakage of detergent from the dispenser, indicating a seal failure.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This dishwasher detergent dispenser assembly stores detergent and releases it at the correct time in the wash cycle to ensure consistent cleaning results. Replacing a worn dispenser restores reliable soap release and helps improve wash performance.

• Holds detergent and opens when signaled by the control
• Common symptoms: detergent cup won't open, soap left in the cup after cycle, broken dispenser door/latch

• Disconnect power to the dishwasher before servicing
• Open the door and remove inner-door screws to access the dispenser
• Release locking tabs, remove the old dispenser, and clean the sealing surface
• Seat the new dispenser evenly, reinstall screws, restore power, and run a test cycle