Dishwasher Dispenser Parts

The Detergent Dispenser Assembly is an OEM part for Bosch dishwashers.  The detergent dispenser assembly works with the control system to release detergent during the wash cycle.  

Causes of a bad detergent dispenser assembly can include broken or loose mounting points, a dispenser that no longer locks into place, or a damaged latch mechanism preventing the dispenser from opening.

Symptoms of a bad detergent dispenser assembly include:

• Detergent not dispensing or distributing as intended
• Dispenser door unable to close or remains open
• Excess clutter inside the dishwasher
• Ineffective cleaning or dirty dishes after cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Note: Check Serial Number for correct part

This replacement door latch engages the strike/catch to keep the door securely closed so the appliance can operate. A worn or broken latch can cause door-closed detection issues, doors that pop open, or cycles that won't start.

• Secures the door by engaging the strike/catch for a positive close
• Ensures door/interlock switches register "door closed" so the unit can run
• Helps maintain a reliable seal and reduces interruptions mid-cycle
• Common symptoms: door won't latch or pops open; appliance won't start; door/latch-related error messages

• Disconnect power to the appliance before servicing
• Note the latch orientation; transfer any original screws/clips as needed
• Align the latch with the strike and tighten fasteners securely
• Close and open the door several times to verify smooth engagement before testing operation

Bosch dishwasher soap dispenser assembly, unvented, dark gray

This replacement dishwasher detergent dispenser stores detergent and releases it at the correct time in the cycle, while also controlling rinse-aid dosing. It restores reliable cleaning performance when the original dispenser is damaged, leaking, or won't open.

• Holds detergent securely and opens on command during the wash cycle
• Meters rinse aid during the final rinse to help reduce spots and film
• Seals to the inner door at the dispenser opening to help prevent leaks
• Typical symptoms: detergent left in cup, dispenser door won't latch/pop open, rinse aid not dispensing or leaking, visible cracks or warping

• Disconnect electrical power and turn off water supply before servicing
• Open the door and remove inner-door panel screws to access the dispenser
• Unplug the wire connector(s), release retaining screws/tabs, and remove the old dispenser
• Clean the door cutout, seat the new gasket evenly, secure the dispenser evenly, reconnect wiring, and run a leak check

The Dishwasher Rinse Aid Dispenser is an essential component for maintaining spotless and efficiently dried dishes in your Samsung dishwasher. This genuine OEM part ensures optimal performance by releasing the right amount of rinse aid during each wash cycle, which helps to prevent water spots and improve drying results. Designed specifically for Samsung dishwashers, this dispenser guarantees a perfect fit and seamless integration with your appliance. The high-quality materials used in its construction provide durability and reliable operation, ensuring that your dishwasher continues to perform at its best for years to come. Installing the Dishwasher Rinse Aid Dispenser is straightforward, allowing you to quickly restore your dishwasherGÇÖs functionality without any hassle. By using this genuine OEM part, you can trust that your dishwasher will operate smoothly, delivering clean and sparkling dishes every time. Enhance your dishwashing experience with the Dishwasher Rinse Aid Dispenser and enjoy the benefits of a well-maintained appliance that efficiently handles your kitchen needs.

This dispenser assembly replaces a refrigerator's door-mounted ice and water dispenser to restore normal dispensing and reduce leaks or delivery issues. It provides the core housing and user-facing dispenser opening for door-based dispensing systems. What it does:

• Directs water and ice from the door dispenser to the user, forming the visible dispensing opening and housing.
• Helps stop common dispenser symptoms such as water dripping from the dispenser opening or ice/jam buildup at the dispenser chute.
• Supports normal push-lever or paddle operation and routes water/ice to the exterior dispense area.

• Disconnect power and shut off the water supply before starting any work.
• Removal typically requires taking off the refrigerator door panel or trim to access mounting fasteners—retain all hardware and note fastener locations.
• Handle the dispenser housing carefully to avoid cracking plastic or damaging seals; inspect gaskets and fittings and replace if brittle.

This dispenser stores the detergent and rinse aid and releases them at the proper time during the cycle, helping your dishwasher clean effectively and reduce spotting. Replacing a faulty dispenser restores consistent soap release and rinse performance. What it does:

• Holds detergent and rinse aid, then opens to release them at the correct stage of the wash
• Helps prevent detergent remaining in the cup after a cycle
• Restores proper latching and sealing of the dispenser door
• Common fix for a cracked housing, broken latch, or rinse aid leaking/over-dispensing

• 1 dispenser assembly

• Disconnect power to the dishwasher before servicing
• Remove inner door panel fasteners to access the dispenser; disconnect the electrical connector
• Release the locking tabs, remove the old dispenser, and seat the new one evenly to ensure a proper seal
• Reassemble the door, restore power, and run a short cycle to check for leaks and proper operation

This actuator arm is the mechanical lever inside the dishwasher door's dispenser assembly. Working with its spring, it releases the detergent cup at the proper point in the cycle to restore consistent detergent dispensing. What it does

• Transfers motion from the control/drive mechanism to the dispenser latch to open the detergent cup
• Provides the spring tension needed for the lever to return to its home position
• Helps ensure detergent is dispensed at the intended time in the wash cycle
• Common symptoms include detergent left in the cup, a dispenser door that won't latch or opens inconsistently, or a visibly broken/missing lever

• 1 actuator arm with spring

• Disconnect power to the dishwasher before servicing
• Open the door and remove the inner door panel fasteners to access the dispenser linkage
• Note the spring orientation; move the spring to the new arm if needed and seat the arm in the correct pivot location
• Reassemble the door and manually test the dispenser action before running a cycle

Wax motor for detergent/rinse-aid dispenser.

This lever connects to the dishwasher detergent dispenser mechanism and actuates the cup lid. A worn or damaged lever can prevent the dispenser from opening at the right time, reducing wash performance.

• Transfers motion from the timer/actuator to release the detergent cup lid
• Common symptoms: detergent remains in cup, soap door won't open, poor cleaning results
• Restores reliable dispenser operation during the wash cycle

• Disconnect power and turn off water before servicing
• Access typically requires removing the inner door panel to reach the dispenser linkage
• Note linkage orientation before removal; transfer any springs or clips
• Test dispenser door movement by hand before reassembling

This dispenser is the door-mounted assembly that delivers ice and/or water from the refrigerator. It replaces a worn, cracked, or malfunctioning dispenser to restore normal dispensing and stop leaks. What it does:

• Provides a finished dispenser opening and support for the actuator and chute so water and ice flow correctly.
• Stops leaks and prevents food or debris from entering the dispenser area when cracked or damaged.
• Restores proper activation when the dispenser lever or paddle no longer engages the valve or auger.
• Helps eliminate jams or misalignment that can cause intermittent dispensing or noisy operation.

• Disconnect power and shut off the water supply before starting any work.
• Remove the inner door panel or trim to access the dispenser mounting screws and wiring.
• Handle gently to avoid cracking surrounding trim; test operation before reassembling the door.

This tank rinse aid assembly holds and dispenses rinse aid during the dishwasher's final rinse to help reduce spotting and improve drying. Replaces a worn or leaking dispenser to restore proper rinse-aid delivery. What it does:

• Stores and meters rinse aid into the final rinse cycle to promote better drying and fewer water spots.
• Can fail to dispense or leak when cracked, clogged, or worn.
• Common symptom indicators: no rinse-aid release, persistent spotting/film on dishes, or visible leaks near the dispenser area.
• Restoring this part often resolves rinse-aid delivery issues without replacing larger components.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Access typically requires removing the door inner panel or lower access panels; follow your model's service manual for exact disassembly steps.
• Inspect surrounding seals and mounting points for damage or residue when replacing the assembly.
• Use only manufacturer-approved replacement parts and torque/fastening practices per the service guide.

This is the lid assembly for the dispenser. It covers and protects the dispenser compartment, helping keep debris out and ensuring the dispenser opens and closes properly.

• Covers the dispenser compartment to prevent spills and contamination
• Helps ensure proper dispenser operation
• Common fix when the dispenser lid is cracked, broken, loose, or won't stay closed

• Disconnect power and shut off water before servicing
• Open the dispenser area and remove any retaining screws or tabs
• Transfer any reusable hardware from the old lid to the new assembly
• Test operation before returning the appliance to service

This bi-metal is the thermal actuator that releases the detergent dispenser at the proper point in the wash cycle. Replacing a weak or failed actuator restores reliable detergent cup opening and consistent detergent delivery for better cleaning. What it does:

• Heats and flexes when energized by the control to trip the dispenser latch
• If failed, the detergent cup may not open or may open inconsistently
• Can leave detergent in the cup and lead to poor cleaning results
• Often suspected when the cycle runs but the soap door stays closed

• 1 bi-metal actuator assembly

• Disconnect power at the breaker before servicing
• Remove the inner door panel to access the dispenser area
• Note wiring positions and orientation; transfer connectors securely to the new actuator
• The dispenser latch/linkage moves freely and test door release before reassembly

A replacement dispenser assembly for refrigerator doors that secures dispenser components and restores normal dispenser function and appearance. Installs in the door to replace cracked, loose, or damaged dispenser housings and trim. What it does:

• Provides the mounting and trim for the door dispenser spout and controls.
• Restores proper alignment and fit when the original dispenser housing is cracked, broken, or loose.
• Helps stop rubbing or interference that can cause the dispenser lever or ice/water chute to stick.
• Addresses visible damage and improves the door's finished appearance.

• Disconnect power and shut off the water supply before starting work.
• Installation typically requires removal of the inner door panel and removal/installation of screws and clips; save all hardware.
• Handle door trim and any water lines carefully to avoid damage; check for leaks after reconnecting the water.