Drip Pan

This dispenser drip tray catches water and minor spills beneath the refrigerator's ice/water dispenser, helping keep the grille area dry and protecting the door from moisture damage or staining.

• Collects drips and splashes from the dispenser to prevent puddling on the door
• Helps reduce staining, mineral residue, and odors around the dispenser area
• Sits in the dispenser grille for easy removal and cleaning
• Common signs it's needed: cracked or warped tray, excessive water on the dispenser shelf, or a missing tray

• Unplug refrigerator or switch off power before servicing
• Lift out the old tray from the dispenser grille; clean area
• Seat the new tray flat and flush in the grille opening
• Verify proper fit and stability before restoring power

This drip tray sits beneath the grate area to catch grease and boil-overs, helping keep the cooktop cleaner and protecting components below. Replacing a bent, corroded, or missing tray restores proper fit and appearance. What it does:

• Collects drips, grease, and spills under the grate area
• Helps prevent liquids from reaching the burner box or wiring
• Supports correct placement of the grate/grill assembly
• Common symptoms: missing tray, heavy rust, warping, leaks or messes under the top

• 1 drip tray

• Disconnect power and shut off gas; allow the appliance to cool completely
• Remove the cooking grates/grill section to access the tray
• Lift out the old tray and position the new one with correct orientation
• Reinstall grates and verify proper seating and clearances before use

This is a refrigerator drip pan kit. It is located on the bottom of the appliance and is used to help catch condensation from the appliance. Any moisture that is made while the refrigerator goes through its operation cycles will collect in the pan to prevent a mess. If the drip pan has been damaged, the most common symptom is water dripping on the floor. Checking for a clog should be done. If the actual part is damaged, it will need to be replaced.Before replacing the drip pan kit, unplug the power cord on the appliance and pull the refrigerator from the wall. Use a nut driver to release the water inlet line coupler before taking off the access panel. Reach in and bend the pan retaining tab, open the doors of the appliance, and take off the water filter cover. Remove the toe plate to access and replace the drip pan.This is a genuine OEM drip pan kit that can be used as a replacement for Dacor, Jenn Air, Hardwick, and Maytag refrigerators. It is sold as an individual component and is provided directly from the manufacturer.

This drip tray collects and channels defrost and condensation water away from the refrigerator interior to help prevent pooling and musty odors. Replacing a cracked or warped tray restores proper water management and reduces leak risk. What it does:

• Captures defrost and condensation runoff and directs it to the drain/evaporation area.
• Prevents water from pooling inside the cabinet or beneath the appliance when functioning correctly.
• Common symptoms that indicate replacement: visible cracks or warping, standing water under the fridge, or persistent musty odors.
• Designed as a direct replacement for the factory drip tray specified for the appliance.

• Disconnect power to the appliance before beginning any service.
• Remove any shelves or drawers needed to access the old tray; handle carefully to avoid damaging surrounding components.
• Do not force the tray into place; make sure it seats correctly in the drain channel and sits flat.
• If water problems continue after installing the new tray, inspect the drain path and drain tube for clogs or damage.

A replacement drain pan that captures defrost and condensation water to keep it contained and away from the cabinet and floor. Restores the appliance's normal water-collection path and helps reduce leaks. What it does:

• Collects melting ice and condensation from the evaporator to prevent water from pooling under the appliance.
• Channels collected water toward the drain system so it evaporates or exits as designed.
• Stops common symptoms like puddles or moisture under the unit and musty odors caused by standing water.
• Fits under the evaporator/coil area to restore proper water management.

• Disconnect power to the appliance before service to avoid electrical hazards.
• Remove the required access panels or move the appliance per the manufacturer's guidance to reach the pan.
• Lift out the old pan carefully—it may contain standing water—and position the replacement so the drain outlet and routing match the OEM layout.
• After installation, restore power and check for proper water flow during a defrost cycle; inspect surrounding seals and tubing for proper seating.

This trough drain collects and channels defrost and condensation water from the evaporator area to the drain system, helping prevent leaks and pooling inside the refrigerator. It restores proper water flow and reduces standing water. What it does:

• Collects defrost/condensation runoff from the evaporator area and directs it to the drain pan.
• Helps prevent water pooling inside the fridge or under crisper drawers.
• Reduces ice buildup and musty odors caused by trapped moisture.
• Replaces cracked or warped troughs that allow leaks or improper drainage.

• Disconnect power to the appliance before beginning any work.
• Remove food, shelves and the evaporator cover/pan as required for access; follow the service manual for your model.
• Clean the drain tube and drain hole before installing to ensure proper drainage.

Replacement drip tray in white that installs under the appliance to collect spills and direct water away from internal components, helping prevent damage and making cleanup easier. What it does:

• Catches leaks, drips and overflow to protect the cabinet and floor.
• Directs water away from controls and electrical components to reduce risk of damage.
• Replaces cracked, warped or discolored trays that no longer hold water.
• Helps limit staining and makes routine cleanup faster.

• Disconnect power to the appliance before starting any work.
• Access the tray by removing the lower access panel or kickplate as required for your model.
• Remove the old tray and slide or snap the replacement into place; avoid forcing parts.

This drip tray is the evaporator drain pan that collects defrost and condensate water to help prevent leaks and water damage beneath the appliance. It restores proper drainage and keeps the cabinet dry. What it does:

• Collects and channels defrost/condensate water away from internal components
• Helps prevent water pooling under or around the appliance
• Reduces risk of water-related damage and odors when installed correctly
• Fits into the factory location to restore original drainage performance

• Disconnect power to the appliance before beginning service to avoid shock.
• Access the tray by removing the lower access panel or grille per the owner's manual.
• Inspect surrounding seals and drain tubing; clear any clogs before installing the new tray.
• Handle parts carefully to avoid damaging adjacent panels; for model-specific instructions.

Color: silver. Measures about 9-1/2 inches wide by 5 inches deep.

This product is a Whirlpool refrigerator drip pan for the evaporator. The drip pan is in place to catch water created from defrosting or condensation created by the evaporator. A damaged or clogged pan will lead to water leaking underneath the appliance. Substantial leaks from the refrigerator need to be inspected. Typically the two leading causes would be a worn-out seal from the door causing ice to melt or a clogged or damaged drip pan. Carefully examine the drip pan to ensure it's not just a clog, which is easily fixable. Any cracks or more significant damage means a replacement should be ordered.Access the drip pan by removing the bottom vent of the refrigerator. The drip pan is connected to the evaporator. Unplug the refrigerator to ensure safety before making any repairs. Carefully unscrew the nut that fastens the connecting line between the evaporator and the drip pan with a wrench. Remove the old drip pan and insert the new product. Make sure the nut is tight enough to make a good connection between the evaporator and the new component.This product is compatible with Whirlpool, Admiral, Magic Chef, Jenn-Air, and KitchenAid appliances. This is a genuine OEM product sourced directly from the original manufacturer.

This is a double drip pan is made for ranges, stoves, and cooktops. This is a genuine replacement part made by General Electric. The double drip pan is situated underneath two heated elements and is able to catch any food or debris that fall when cooking. The double drip pan is there to catch any and all waste so that the user may easily clean up after the heat is turned off and the appliance is cooled down.A new double drip pan might be needed if the current one is damaged in any way including being broken or bent so that is it not fully secure under the burner. This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with ranges, stoves, or cooktops made by General Electric.

This drip bowl catches and channels excess moisture or drips to help keep the area under the dispenser or ice/water outlet clean and dry. Durable molded plastic resists staining and is shaped for correct fit and drainage. What it does:

• Collects and directs drips from the dispenser or outlet to prevent pooling
• Helps reduce water on the cabinet floor and in the drip tray area
• Restores proper alignment and containment when the original bowl is cracked or warped
• Compatible with units that use an 8" black drip bowl as the dispenser/collector component

• One 8" black drip bowl

• Remove power to the appliance before beginning any service
• Typically snaps or slides into place; check for retaining clips or mounting tabs
• Inspect surrounding seals and gaskets; replace if damaged to prevent leaks

A decorative trim ring that restores the original finish and helps secure surrounding components on your appliance. Replaces cracked, faded or loose trim to improve appearance and maintain a proper fit. What it does

• Covers and finishes the edge of a control or opening to give a clean, factory look.
• Holds adjacent trim or components in place to prevent gaps and rubbing.
• Hides wear, scratches or discoloration for an improved appearance.
• Common symptom: visible cracks, chips, or a loose/misaligned trim piece.

What's included

• One trim ring.

Install notes

• Disconnect power to the appliance before starting any work.
• Use basic hand tools; avoid overtightening fasteners to prevent cracking the trim.
• Handle plastic trim carefully to avoid scratches; align tabs/clips before fastening.

A left-side double burner pan that supports two cooktop burners and helps contain spills and drips for easier cleanup. Durable replacement to restore proper burner support and alignment on compatible gas ranges. What it does

• Holds and centers two adjacent burners so pots and pans sit flat and stable.
• Helps catch food, grease and liquids to prevent spills from reaching the cooktop cavity.
• Fits into the left-side pan location and works with the cooktop's burner assembly.

• Allow the cooktop to cool and shut off power/gas to the appliance before starting.
• Remove grates and existing pans carefully; align the replacement pan to the burner openings and set into place.
• Use non-abrasive cleaners to avoid damaging the finish; avoid bending or flexing the pan during install.

This vaporizer pan and drip tray assembly fits refrigerators. When the freezer automatically defrosts, meltwater must be moved out. It empties out of a drain line into the drain pan/drip tray. The vaporizer portion of the assembly then helps to evaporate the water. Made from stainless steel, it resists corrosion and damage, but prolonged use may result in rust. Eventually, it will need to be replaced.The most common sign that the drip tray and vaporizer pan need to be replaced is visible water leaking from under the refrigerator, or the drain line backing up into the freezer. Replacement will require accessing the bottom of the refrigerator. Unplug it from the power, then locate the four bolts that hold it in place. Use a ratchet and socket to remove the bolts, and then install the new pan assembly.This is a genuine OEM part. It is sold individually, and is designed to work with GE refrigerators.