Frigidaire Parts

I replaced the part by popping off the plastic frame and removing several easily-accessable screws. Three small electrical plugs had to be popped off too. It was a very simple repair. The Sears guy wanted $395 total for the repair, and I did it myself for the price of the part on this site (around $90). Very pleased! Read more

Easy to replace with the shield and paddle assembly. Steps are: 1. use a flat head screwdriver to push the tabs at the base of the control panel. remove the wire connectors by gently prying them straight off. 2. remove the 4 phillips screws holding in the old assembly. 3. Install the new assembly by carefully putting the paddle behind the water pipe that sticks out. You may have to push the paddle one way to get it around the pipe and then back into place. 4. reinstall the screws. 5. reconnect... Read more

• Element will not heat
• Little to no heat when broiling
• Oven not heating evenly

With my tools Read more

The part just snaps on the basket. You have to remove the clips on the end of the runner arms to be able to remove the basket. Once it was out the old arm snap off and you snap on the new arm. Only problem was my old arm was fine and I wished the company would just sell the gasket. It seems a waste to have to purchase the whole arm. The complete job took me about 10 minutes from start to finish. I ordered the part online a Sunday afternoon and it arrived at my house on Tuesday. Read more

Installed a new user interface assembly Read more

Used same tools as in your video. Read more

Online chat here said that the oven sensor should be replaced. I got the feeling that was a bit off, so I went with my gut and ordered the thermostat as well. Replaced the sensor and that didn't fix it. Replaced the thermostat and it worked like a charm! Disappointed that they were overconfident in their answer and it would have taken me more days to fix - but, the products came in quickly (basically, next day) and were correct. Online video for my particular oven was incorrect - but it's... Read more

I ordered a new kit and replaced it. It was easy except the video on the website did not include how to get off the front sticker. However, I did find another video to help Read more

Ordered part from appliancepartspros.com and got them within 2 days.that was great,refrigerator is like new again,am I am pleased with service and there swift delivery. If I need any thing else,there is only one place I will get them.from. Thanks! Read more

• No heat or not enough heat

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

Ordered a new seal, and replaced it with a new one freezer works great now. Read more

Started with replacing hinges. Had to glue the door hinge to refrigerator and secured with two small screws. This refrigerator is in a business with about 50 employees. Suspect minion was not working for some time causing the hinges to get broken. . Read more

First off thanks AppliancePartsPro.com... Another project in the books... I ordered a new switch harness and spark module because I just decided the why not do them both. They arrived very promptly, uses very simple tools most people have I would think. After unplugging it and shutting off the propane. I removed valve knobs. Then the burners with a nut driver and two sizes of sockets. The stove top and valve cover six Philips head screws. Gained complete access to the stove top. Removed... Read more

Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more

I purchased a new elelmnt and fixed it myself!! Read more