Frigidaire Switch

Has three terminals.

The Starter is an OEM replacement part for Frigidaire refrigerators. This component is crucial for initiating the compressor, which is responsible for cooling the refrigerator. The starter works by providing the necessary electrical power to get the compressor running, ensuring that the refrigerator maintains the correct temperature.

Causes of a bad starter can include electrical malfunctions, wear and tear over time, or damage from power surges. A faulty starter can prevent the compressor from starting, leading to cooling issues.

Symptoms of a bad Starter include:

• The refrigerator not cooling properly
• The compressor not running or frequently cycling on and off
• Unusual clicking or buzzing noises from the compressor area
• The refrigerator being warmer than usual or food spoiling quickly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.

• Directs power to the associated circuit when switched on or off
• Common symptoms: function won't turn on/off, intermittent operation, or the switch feels loose/sticks
• Helps restore positive, consistent control from the backguard/control panel

• Disconnect power at the breaker before servicing
• Access the switch from the control panel/backguard; retain screws/clips
• Label/photograph wire positions and transfer leads one at a time to the new switch
• Ensure firm terminal connections, reassemble, restore power, and test operation

Fix water or ice dispenser not working with this 4-button control switch assembly. Common fix when buttons fail to respond or dispense incorrectly.

Oven light stays on or won't turn on when door opens? This door-activated switch restores automatic light control. Easy 15-minute DIY repair.

Fix intermittent burner failures or electrical issues with this range wiring harness. Restores power flow when connections are loose, burnt, or broken.

If your hood won't turn on or respond to controls, this switch may have failed. Requires removing the grease filter and lower pan to access and replace.

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

Interior light stays on or won't turn on? This upright freezer door switch controls lighting when the door opens and closes. Simple fix for most DIYers.

This is a factory switch used in the appliance's control/safety circuit. Replacing a worn or failed switch restores reliable signaling so the selected function engages properly and the unit responds consistently to user inputs and status conditions.

• Provides an electrical on/off signal to the control or safety circuit
• If faulty, selected functions may not activate or may be intermittent
• Can trigger error codes related to a switch input, depending on model

• Disconnect power before servicing; turn off gas/water if applicable
• Note/photograph wire locations and transfer connectors one at a time
• Verify actuator alignment and secure mounting before reassembly
• After installation, run a test cycle to confirm proper operation

Interior light won't turn on when door opens? This push-button door switch restores automatic lighting. Moderate DIY repair with basic tools.

This wiring harness routes power and control signals between key components inside your range or wall oven. Replace a damaged harness to restore safe, reliable operation and prevent intermittent heat, shorts, or non-working burners and oven functions.

• Distributes electrical power and signals between controls, switches, heating elements/igniters, and safety components
• Maintains correct connector orientation and wire routing for dependable operation
• Typical symptoms: no heat in oven or on surface burners, intermittent operation, breaker tripping, or visible burnt/melted wiring
• Restores stable connections to reduce arcing and overheating

• Disconnect power at the circuit breaker; for gas ranges, also shut off the gas supply
• Label or photograph all connections and transfer one wire at a time to avoid miswiring
• Route the harness exactly as original; keep away from sharp edges and hot surfaces; secure with existing clips/ties
• If connectors don't match or any terminals are heat-damaged, stop and inspect mating components.

Burner won't heat or stays on constantly? This range burner control switch regulates cooktop element temperature. Straightforward DIY fix.

Fix E32 error codes or washer stopping during fill with this water level pressure switch. Senses water level and controls fill cycles. DIY-friendly repair.

This is the user control and display board located on the front panel of the dishwasher. It contains the buttons, display, and interface circuitry that allow you to select wash cycles, options, and monitor cycle status. Replace this board if the display is blank or flickering, buttons are unresponsive, or the dishwasher does not respond to cycle selections.

If your cooktop burner won't heat, stays on high, or won't turn off, a faulty burner control switch is often the cause. DIY repair in 15-30 minutes.