Need Help?
Call or text
If your oven won't heat or igniter glows but gas won't light, the igniter is likely weak. This is a common DIY repair taking 15-30 minutes.
The bake (bottom burner) worked after replacing the ignitor. Becareful and do not drop the ignitor or the element will break. I found out the hard way. I bought the first ignitor at a local appliance store. After breaking that one, I found another at appliancepartspros.com for $20 cheaper. Thanks appliancepartspros!!! Read more
Clear plastic lid cover for refrigerator pantry drawer. Replaces cracked, broken, or missing pantry lid. Snaps into place over drawer compartment.
Replaced the broken parts. The water leak was caused by the drain valve not directed into drain pan Read more
The Large Surface Element is an OEM component for Whirlpool ranges. As a key heat source, it withstands significant thermal stresses each use for cooking tasks. This surface element measures approximately 10” in diameter.
Over time, micro
Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more
Refrigerator shelf frame that supports glass or wire shelves inside the fridge. Replace if cracked, broken, or warped to restore proper shelf support.
No instructions are included with either piece, which makes installation take more time and care. Tools needed: Small standard flat blade screwdriver, box knife or other knife with at least a 2" long blade, super glue. Remove the old main crisper frame: 1. Remove old main frame by lifting upward and outward. 2. Remove the center rail from the frame. May require bending of the main frame to remove it. 3. Remove the crisper front panel by unsnapping from frame. This is easily done by... Read more
The Defrost Thermostat and Wiring Harness is an OEM part for Whirlpool refrigerators. This part ensures that the refrigerator's evaporator coils do not become overly frosty, thereby maintaining optimal air flow and cooling efficiency throughout the
Replaced the defrost thermostat and heater and the refrigerator was working again. Read more
Replacement crisper pan for bottom-mount refrigerators. Stores fruits and vegetables in the fresh food compartment. Replace if cracked, broken, or missing.
The manual had instructions for pulling things apart, the flaps over the drawer tops and the clear plastic inserts in the shelf. Flaps--Easiest to work with when the shelf is out and upside down. Slide flaps to the side a little to release the axle pin on the flaps from the receptacle hole on the shelf frame. Clear plastic plates are held in with a plastic pin on the side of the shelf frame. Carefully pull the side off the shelf there away from the pin slot until the insert pops out.... Read more
Replacement glass shelf for refrigerator interior storage. Installs in shelf frame to hold food items. Order if original is cracked, shattered, or broken.
I took apart the old bucket with a screwdriver and put the new one with no problems. Read more
Creates an airtight seal around your freezer door to prevent warm air entry and cold air loss. Replace if torn, cracked, or not sealing properly. Verify fit by model number.
Ordered the new gasket from you - installed it and now my freezer is sealed i called to order the correct replacement and they were the very best at helping me !!!!! Read more
The LP Conversion Kit is an OEM component for Whirlpool and KitchenAid gas dryers. It allows conversion from natural gas to liquid propane fuel operation. Over time in gas-powered dryers, improper gas/air mixture causes part wear like weakened burner c
Ordered the parts from ApplianceParts Pros.com and saved the $100 service call. The fix was easy, complete instructions enclosed. Read more
Seals the freezer door to prevent warm air from entering and maintain temperature. Replace if torn, cracked, or not sealing properly. Confirm fit.
Purchased freezer door gasket and installed it as per your video online. Read more
The Counterbalance Spring Kit is an OEM part for Whirlpool washing machines. This kit includes springs that help balance and stabilize the washer drum during the spin cycle, preventing excessive movement and vibration. The counterbalance spring ki
My wife and I along with Mat on the video replaced the upper and lower friction pads, along with the balance springs. The machine runs smooth as it did new. Thank you everyone at Appliance Parts Pro and Mat. You are a great company. P.S. my wife and I should had made our own video for you since we are both in our 60s I bet it would have been funny Thanks Again. JIm & Debbie from Texas. Read more
Suspension spring kit for front-load washers. Supports the tub assembly to maintain balance during cycles. Replace if springs are broken, stretched, or missing.
Ordered the springs and shocks. Noticed that the washer had placement for 4 springs, but the factory only installs 2 (or they forgot to install the other two on my machine). If you replace the springs, be sure to check for the spring bracket mount. You will also need those. The washer is running fine. Next I'll work on the dryer. Read more
The Jar is an OEM part for Whirlpool blenders. This jar serves as the container where ingredients are placed for blending, mixing, or pureeing. This plastic jar measures approximately 8 inches wide by 10 inches high and has a capacity of 56 liquid ounc
Most of the instructions you find online are for a different type of coupler that pops off. This model is different, as the coupler unscrews. I found a video for this specific model blender and I'll summarize below: Turn the blender over so the bottom of the blender is facing up You have to pop the bottom rubber feet off. Take off the four screws on the bottom of the blender Lift the bottom of the blender up and off. This may take two people. You'll need a heavy duty wrench under... Read more
Fix a noisy or non-cooling refrigerator with this condenser fan motor. Solves overheating compressor issues. DIY-friendly repair with video guide.
I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more
Replaces the water tube that runs through your refrigerator door to the dispenser. Needed when the original tube is cracked, broken, or leaking.
I watched the videos for both jobs, which were excellent and "spot on" for the repair jobs.It didn't take me an hour to replace both lines. Keep up the good work on helping us repair and save money doing our own work. Ken Read more
Seals freezer door to prevent warm air entry and maintain optimal temperature. Replace if worn, cracked, or causing frost buildup. Confirm fit by model.
Purchased replacement door gasket (seal). Pulled old gasket from its groove around door. Easily pressed the replacement gasket into the empty groove. Repair complete. Read more