Latch, Catch, Lock Parts

Replace a lost or broken refrigerator door lock key to restore security and access. Simple replacement takes just minutes with the right key.

The Dryer Door Latch Kit is an OEM part for Whirlpool dryers. It ensures the dryer door stays securely closed during operation, allowing the dryer to function correctly and safely. This kit typically includes the latch, strike, and necessary mounting hardware for easy installation.

Causes of a bad door latch can include wear and tear from frequent use, accidental damage from forceful closing, or alignment issues due to the door being knocked out of place. A faulty latch can prevent the dryer from starting or cause it to stop mid-cycle if the door doesn't stay closed.

Symptoms of a bad dryer door latch include:

• The dryer door not staying closed
• The dryer not starting or stopping unexpectedly during a cycle
• Difficulty in closing or latching the door
• Loose or misaligned latch components

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Fix DE door error codes or doors that won't latch with this washer door latch hook. Simple 15-minute DIY repair with video guide. Secures door during cycles.

Fix a washer that won't start or run because the door won't lock. This door lock assembly secures the door during wash cycles. DIY-friendly repair.

Washer won't start and door won't lock? This door latch securely holds the door closed during cycles. Moderate DIY repair with multimeter testing.

This replacement magnet is used in select refrigerator assemblies. It provides the magnetic hold or sensor trigger required so doors, flaps, or rails stay closed and so the controls can accurately detect when components are in position.

• Supplies magnetic retention in the specified assembly to keep parts closed and aligned
• Activates magnetic reed sensors in models that use them for door/position detection
• Weak or missing magnets can lead to door-ajar alerts, air leaks, or components not staying shut
• Visible damage or incorrect orientation can cause intermittent operation or improper sealing

• Disconnect power before servicing; turn off water if working near the dispenser
• Use your model's parts diagram to locate the magnet and note its orientation/polarity
• Press-fit into its holder carefully; do not chip or crack the magnet
• Verify proper closure/sensing operation before returning the appliance to service

Fix a loose refrigerator bin or drawer with this latch. Secures bins to mounting points, preventing spills and drops. Easy DIY replacement.

Door lock secures the appliance door during use, allowing cycles to start and run safely. Replace a broken or failing lock to restore proper closure and prevent interruption of operation. What it does:

• Latches and holds the door closed so the appliance can start and complete cycles.
• Triggers the control to allow operation only when the door is fully closed.
• Common symptom: appliance won't start or stops mid-cycle because the door won't latch.
• May be needed if the door feels loose, won't stay closed, or you hear clicking when trying to start.

• Disconnect power (and water, if applicable) before starting any repair.
• Handle parts carefully; avoid forcing or bending mounting tabs during installation.
• Verify proper alignment and engagement of the latch before restoring power.

Dryer won't start or stops mid-cycle? This door lock assembly secures the door and engages the safety interlock. Straightforward DIY repair.

This latch assembly secures the trash compactor drawer in the closed position and engages the safety interlock that allows the compactor to operate. It mounts to the front of the compactor frame and connects to the door switch mechanism. Replace this part if the drawer will not latch shut, the compactor fails to start because it does not detect a closed door, or the latch mechanism is visibly broken or worn.

A replacement motor latch that secures the motor assembly to the appliance chassis, helping keep the motor stable during operation for smoother performance and reduced vibration. Fits specific Frigidaire/WCI motor assemblies. What it does:

• Secures and positions the motor assembly to prevent excessive movement
• Helps reduce vibration and rattling caused by a loose motor mount
• Restores proper alignment between motor and drive components
• Can eliminate intermittent contact-related noise from a shifting motor

• Disconnect power (unplug or switch off breaker) before starting any repair
• Installation typically requires accessing the motor area—expect to remove panels or the cabinet
• Keep track of mounting hardware; replace any damaged fasteners
• Test operation after reassembly; stop and recheck if noises or vibration persist

Oven door won't stay closed or lock during self-clean? This door latch secures your oven door and engages during cleaning cycles. Simple repair.

Fix a microwave door that won't open or latch properly with this sliding latch component. Restores secure door engagement when the release button fails to work.

Fixes oven door that won't latch or stay closed. This latch and harness assembly secures the door and sends the closure signal to the control board.

Fix a warm fridge or frost buildup with this door gasket magnetic strip. Restores the seal when cold air escapes. Easy DIY repair in under 30 minutes.

Fix a compactor door that won't stay closed or latch properly with this door strike and catch. Restores secure door closure for safe operation.