Lg Screws, Nuts, Washers

This factory fastener secures appliance panels and components. Use it to replace a missing, stripped, or corroded screw so brackets, covers, and assemblies stay tight and properly aligned, helping reduce vibration and rattling.

• Secures panels, brackets, and internal components in their proper positions
• Replaces missing, worn, or cross-threaded hardware
• Helps eliminate vibration and rattling from loose parts
• Supports proper alignment of covers and assemblies

• Disconnect power to the appliance before servicing; allow any moving parts to stop
• Match this screw to the location shown in your model's parts diagram
• Start threads by hand to avoid cross-threading, then tighten snugly with the correct driver
• Do not overtighten to prevent stripping threads or cracking plastic bosses

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This replacement screw secures panels and components on LG appliances to restore proper alignment and prevent rattling or loose parts. It's a direct-fit fastener used where OEM mounting hardware has become stripped, lost, or damaged. What it does:

• Secures panels, brackets, or trim to maintain appliance structure and alignment
• Helps stop vibration noise caused by loose panels or components
• Replaces missing or damaged mounting hardware to prevent parts from shifting
• Restores proper fit where stripped or worn screws no longer hold

• Use the correctly sized screwdriver or bit to avoid stripping the head
• Tighten snugly but do not overtighten; excess torque can strip threads or crack plastic
• If working near electrical components, unplug the appliance first to ensure safety
• Keep removed screws organized during disassembly to match locations on reassembly

A single mounting screw used to secure panels, brackets, or components in place so assemblies stay stable during normal appliance use. Simple replacement for stripped or missing fasteners. What it does:

• Secures panels, trim, brackets or interior components to prevent rattling or movement
• Restores proper fit and alignment after service or accidental damage
• Helps reattach parts removed during maintenance or part replacement
• Small, durable fastener designed for appliance interior mounting applications

• Use the correct screw driver or bit to avoid stripping the head
• Match screw length and thread engagement to the original location before tightening
• Tighten until snug—do not overtighten to avoid cracking plastic or damaging threads
• Disconnect power and follow appliance safety procedures before performing repairs

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This replacement screw secures panels, trim and internal components to restore a tight fit and stop rattling or loose parts. Use it when a missing or stripped screw causes panels or controls to shift. What it does:

• Secures panels, trim pieces or mounting brackets to keep components aligned
• Stops rattling, vibration noise or loose-fitting panels
• Replaces missing or stripped screws to restore proper fastening
• Helps ensure other parts stay in position during normal use

• Disconnect power before working on the appliance to prevent shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and tighten until snug; avoid overtightening which can strip threads or crack plastic
• Replace with the exact OEM screw if available to ensure proper fit and function

This is a genuine replacement mounting screw designed to secure appliance panels and internal components, restoring proper fit and stopping movement. Fits specified LG assemblies where the original screw is missing or damaged. What it does:

• Secures panels, brackets, or small components to prevent rattling and misalignment
• Restores proper attachment when original screw is stripped, lost, or broken
• Helps eliminate vibration noise caused by loose fasteners
• Matches OEM fit and thread form for reliable reassembly

• One mounting screw

• Disconnect power and water before beginning any service
• Use the correct driver and do not overtighten to avoid striping threads or cracking components
• Keep removed screws organized to ensure correct replacement locations
• If threads are damaged, replace mating clip or insert as recommended by OEM

This screw is a direct-fit replacement fastener that secures panels, brackets, and internal components. Replacing a missing or stripped screw helps stop rattling and keeps parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets, or internal components to restore proper fit
• Replaces missing or damaged hardware that can cause rattling or loose parts
• Restores alignment so doors, shelves, or assemblies operate smoothly
• Provides a straightforward hardware fix without replacing larger assemblies

• Use the matching screwdriver or driver bit to avoid stripping the head
• Do not overtighten — snug until seated to avoid damaging threads or plastic parts
• Disconnect power or follow appliance safety instructions before servicing electrical areas
• Keep removed hardware organized and save any damaged parts for inspection

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening

This replacement screw secures panels and internal components in compatible LG appliances, restoring proper fit and preventing rattles or loose parts. Use it to replace a missing or stripped fastener for a snug, reliable fit. What it does

• Fastens panels, brackets, or components to appliance frame or assemblies
• Helps stop vibration and rattling caused by missing or loose screws
• Restores proper alignment of removable panels or covers
• Works where the original appliance screw has worn, stripped, or gone missing

• Replacement screw as shown

• Disconnect power and water supply to the appliance before beginning any repair
• Use the correct-size screwdriver or driver bit to avoid stripping the head
• Thread carefully and avoid over-tightening to prevent damage to threads or components
• Keep removed screws organized and compare head and length to the replacement before installing

This replacement mounting screw secures panels and small appliance components to restore proper fit and prevent vibration or loose parts. A simple, direct replacement when the original fastener is missing or damaged. What it does:

• Secures panels, brackets, or small assemblies to keep parts aligned
• Stops rattling or vibration caused by loose or missing screws
• Restores normal fit where a stripped or corroded screw failed
• Matches the OEM fastener form for a correct, long-lasting fit

• Unplug the appliance or disconnect power before servicing
• Use the correct driver to avoid stripping the head
• Thread carefully and do not overtighten to prevent damage to threads or housing