Maytag Control Board

This electronic control board is the refrigerator's central control module, coordinating cooling and defrost functions for stable temperatures. Replacing a failing board helps restore proper operation of the compressor, fans, and related circuits.

• Regulates cooling by switching the compressor and fans based on sensor input
• Controls and times the automatic defrost cycle to prevent frost buildup
• Supplies logic and power to temperature controls and indicators
• Can cause no-cool, intermittent cooling, constant running, or unresponsive controls when faulty

• Disconnect power to the refrigerator before servicing
• Handle the board by the edges and use ESD protection if available
• Photograph/label connectors and transfer wiring one at a time
• Some models require control setup or calibration—follow the appliance's service instructions

This washer timer is the mechanical cycle controller that sequences power to the motor, pump, and water valves. Replacing a worn timer restores proper cycle advancement so the washer starts, progresses, and stops at the correct times.

• Controls the length and order of wash, rinse, and spin cycles
• Directs power to the drive motor, drain pump, and inlet valves as the cam advances
• Advances the cycle automatically; interfaces with the timer knob for manual selection
• Failure symptoms include cycles not advancing, stopping mid-cycle, skipping steps, or no start

• Disconnect power and turn off water supply before servicing
• Access the control panel; remove the knob/dial and mounting screws to release the timer
• Note wire positions or take a photo; transfer connectors one at a time to matching terminals
• Reinstall, secure the timer, and run a short test cycle to ensure proper advancement

This electronic control board is the appliance's main control. It coordinates cycle timing and powers key components, helping restore normal operation when the original board fails or causes unresponsive controls, stalled cycles, or error codes.

• Manages inputs from sensors and the user interface to execute programmed cycles
• Distributes power to motors, valves, heaters, fans, and other loads as required
• Stores and runs cycle logic and built-in safety interlocks
• Common symptoms of a failing board: unit won't start, unresponsive controls, cycle won't advance, error codes or blinking lights, intermittent operation

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD protection and handle the board by the edges to avoid static damage
• Photograph/label wiring and transfer connectors one at a time to matching terminals
• Follow the tech sheet/service manual after installation; ensure covers/gaskets are reinstalled to protect the board

This timer is the mechanical cycle controller for select top-load washers. It sequences power to the motor, water inlet valves, and drain pump so each step runs in the correct order and duration for consistent, reliable operation.

• Directs power to advance the washer through fill, wash/agitate, drain, and spin
• Restores proper cycle advancement when the washer stalls or skips steps
• Helps resolve symptoms like stopping mid-cycle or running indefinitely
• Can correct intermittent or erratic cycle timing/advancement issues

• Disconnect power before servicing; access the timer from the control console
• Transfer wires from the old timer to the new one, moving one connection at a time
• Reuse existing mounting hardware and control knob/dial as applicable
• Handle sharp cabinet edges and verify dial alignment before reassembly

This genuine replacement part is a control board. The control board is responsible for sending signals to determine the oven's various functions. Attached to the buttons, the control board's circuits allow for the temperature and timer to be adjusted on the oven.To replace the control board, first, make sure that the circuit breaker is off and the oven is unplugged. Pull out the oven to gain access to the back of the range. Locate the upper back panel and remove screws to expose the back of the control board. Pop out the old control board and take note of any wires that are connected. Unplug the wires from the old control board, and resecure them into the new part. Place it back to its original space, and resecure the back panel of the range.This is a genuine replacement part for an control board compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and Roper ovens.

This replacement part is a control board that has been manufactured by Whirlpool and is compatible with refrigerators. The control board is important for proper appliance functionality, as it regulates and manages refrigerator functions, including the defrost times and the cooling. If the control board is broken, the refrigerator may experience a number of issues, including an inability to maintain cold temperatures or properly regulate defrost cycles. Ensure that perishable foods are stored safely and then unplug the appliance before attempting any repairs.This is a genuine OEM part that has been sourced directly from the manufacturer. It is compatible with refrigerators manufactured by Whirlpool, Maytag, Kitchenaid, Jenn-Air, Magic Chef, and some other brands. This part is sold individually.

This is a mechanical defrost timer that controls the automatic defrost cycle of the refrigerator. It periodically shuts off the compressor and energizes the defrost heater so frost can melt, helping maintain proper cooling performance.

• Cycles the unit between cooling and defrost at set intervals
• Stuck or failed timers can cause warm temperatures, heavy frost, or continuous running
• Can also cause short-cycling or no-cool if contacts fail

• Disconnect power before servicing
• Access is typically from the control housing or rear service area; note wire positions before removal
• Replace one-for-one with the same terminal orientation; do not force the cam
• After install, allow one full cycle to verify defrost operation

Restore reliable cycle control with this electronic control board. It serves as the dishwasher's brain, coordinating wash, drain, and dry functions so the machine starts, runs, and completes cycles as expected.

• Orchestrates cycle timing and interprets sensor inputs
• Distributes power to components such as the wash motor, drain pump, and water inlet valve
• Communicates with the user interface to execute cycle selections
• Typical failure symptoms include: won't start or power up, cycles won't advance, stops mid-cycle, won't fill or drain, or control-related error codes

• Disconnect power at the breaker and turn off water supply before servicing
• Use ESD protection and handle the board by its edges only
• Access the control area, move wire connectors one at a time to the new board, and secure it in the original mounting
• Restore power and, if available, run the unit's diagnostic/service cycle to verify operation

This electronic control board is the appliance's central controller, directing power and timing to key components. Replacing a failed board can resolve unresponsive controls, cycles that won't start or advance, no display, or recurring error codes.

• Distributes power and manages timing for motors, pumps, fans, heaters, and valves
• Interprets inputs from sensors and switches to execute programmed operations
• Stores and runs the appliance's control logic and settings
• Common failure symptoms: no power/display, won't start, stops mid-cycle, intermittent operation, or error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the board by the edges only
• Photograph wiring and move connectors one at a time to the new board
• Some models require configuration or programming after install—follow the service/tech sheet for your unit

Fridge not cooling or running constantly? A faulty defrost timer causes frost buildup and temperature swings. Most DIYers replace it in 15 minutes.

Dryer won't advance through cycles or stops mid-cycle? This timer cam controls cycle progression. Common fix for timing issues, moderate DIY repair.

Replace a failed range clock/control with this factory Clock and Overlay Kit. It restores a readable display and responsive keypad so you can set time, temperature, and cooking modes confidently on compatible ranges and wall ovens.

• Controls oven functions by processing keypad input, driving the display, and switching bake/broil circuits via internal relays
• Common failure symptoms include a blank or erratic display
• Keypad buttons may be unresponsive or intermittent
• Oven may not start or heat due to the control not sending power
• Control-related error messages or beeping can appear

• Disconnect power at the breaker before servicing; verify no voltage is present
• Handle the control with ESD care; avoid touching circuitry and connectors
• Move wires one at a time from old to new control; take photos for reference
• Align and apply the overlay carefully to a clean surface before pressing into place

This part is a moisture sensor control board that is used on dryer units. This component monitors the moisture levels within the dryer and adjusts the dry time during the automatic drying cycle. A new moisture sensor control board will be needed if the time is not advancing in the automatic drying cycle, even if it does advance in the timed dry cycle. Another sign is if the dryer continues to run after the clothing inside is dry. Unplug the dryer from its power source prior to replacing this component. The person performing this task may wish to wear work gloves to protect their hands.The moisture sensor control board is compatible with dryers that are manufactured by Kenmore, KitchenAid, Kenmore Elite, Whirlpool, Amana, Crosley, Maytag, Inglis, Sears Canada, Roper, and Sears. This part is sold individually and it is a genuine OEM replacement part that comes straight from the manufacturer.

Washer won't start or trips breaker? This RFI noise filter conditions AC power and protects control circuits. Easy DIY fix with video guide included.

This clock and overlay assembly replaces the oven/range electronic control and faceplate. It restores a readable display and responsive keypad so you can set time and manage bake and broil functions reliably.

• Controls oven functions and displays time, temperature, and status
• Sends commands to heating circuits for bake and broil
• Helps resolve blank, dim, or erratic display behavior
• Addresses unresponsive or intermittently working keypad buttons
• Can correct persistent beeping or control-related error indications

• Disconnect power at the breaker before servicing; verify no voltage is present
• Handle the control board carefully to avoid electrostatic damage; protect connectors
• Note or photograph wire locations and transfer any brackets from the original part
• Mount securely; align and apply the overlay to a clean surface, then restore power and test

This electronic control board is the appliance's main control module that processes user inputs and manages cycle operations so the unit responds correctly. Replace a failed board to restore normal control and display functions. What it does:

• Receives signals from the user interface and controls timers, relays, and system sequencing
• Powers and coordinates heating/motor/cycle commands as directed by selected settings
• Common symptoms: blank or erratic display, unresponsive touchpad/buttons, cycles won't start, or intermittent operation
• Works as the central logic board; does not include user interface or touchpad

• Disconnect power before service to avoid shock or damage
• Handle the board by its edges and avoid static discharge; ground yourself before touching electronics
• Verify all wire harness connectors are fully seated and mounting hardware is secure after installation