Maytag Control Board

If your range display blanks out, shows error codes like F8:E0, or doesn't respond to controls, the electronic control board likely failed. Restores normal operation.

3 pin 60 minute

Fixes refrigerator displays flashing, unit cycling on/off, or fans not running. This power supply board converts AC to DC for controls and components.

If your oven control flickers or resets randomly, the transient suppressor may have failed. This part protects the control board from power surges.

This electronic oven control replaces the console control used to operate a single-convection oven, restoring user inputs and cycle selection so you can reliably set temperature, timers and cooking modes. Ideal when display, touchpad or convection functions fail. What it does:

• Replaces the oven's main user control to allow selection of bake, broil, convection and timed functions
• Restores touchpad/button input and on-screen feedback when controls are unresponsive or blank
• Helps resolve symptoms such as no display, unresponsive buttons, or inability to start bake/convect cycles
• Interfaces with oven components to relay temperature and command signals to the heating system

• One control (single-conv) as shown

• Disconnect power at the circuit breaker before starting any work to avoid shock hazard
• Handle the control assembly carefully; avoid touching circuit board components and use anti-static precautions if available
• Installation typically requires removing the oven console or back access panel and unplugging the old control connector—refer to OEM service instructions

This mechanical cycle timer controls the sequence and duration of washer operations. Replacing a failing timer restores proper advancement through fill, agitate, drain, and spin so cycles complete reliably with accurate timing. What it does:

• Advances the washer through each step by routing power to the water valves, motor, and drain pump at the correct times
• Sets the length of each stage for consistent operation
• Common failure signs: cycle won't advance or stops mid-cycle
• Timer knob doesn't move or must be jiggled to run
• Skips functions (no agitate, drain, or spin) while others still work

• 1 mechanical timer assembly

• Disconnect power before servicing; access the timer from the control console
• Take photos or label wires; transfer them to the new timer one at a time to maintain correct positions
• Reuse the existing knob and dial; align the timer shaft properly and secure the mounting screws
• After reassembly, run a short test cycle to ensure proper advancement

Fixes oven that won't heat, turns on by itself, or has unresponsive buttons. Moderately difficult repair requiring power disconnect and panel removal.

Refrigerator not cooling or control panel unresponsive? This electronic control board manages temperature and dispenser functions. Moderate difficulty.

Fixes refrigerator not cooling or freezing caused by failed compressor inverter. Restores variable-speed compressor operation and consistent temperatures.

Fix excessive frost buildup in your freezer with this defrost timer. Restores the 6-hour defrost cycle to keep cooling consistent. Moderate DIY repair.

This is a temperature control switch used in a warming drawer to regulate the heat setting. It allows the user to select and maintain the desired warming temperature. Replace this switch if the warming drawer does not heat, stays on one temperature regardless of the setting, or does not respond when the control is adjusted.

Fix an oven with no display, unresponsive buttons, or temperature control issues. This electronic control board restores user input and cycle selection.

Fix unresponsive touchpad, buttons not working, or blank display issues. This oven control board replacement takes 30 minutes with basic tools.

This fountain switch controls the refrigerator dispenser's user-activated circuit so the dispenser responds when the lever or pad is pressed. Replaces a worn or failed dispenser switch to restore normal dispenser control. What it does:

• Acts as the user-activated switch for the water/ice dispenser circuit
• Allows the dispenser to energize the valve or auger motor when pressed
• Commonly replaced when dispenser fails to respond or is intermittent
• Helps stop unexpected dispenser activation due to a stuck switch

• One fountain switch

• Disconnect power to the appliance before beginning any repair
• Access may require removing the dispenser/control panel; handle plastic trim carefully
• Avoid pulling on wires; disconnect connectors by their housings, not the wires

Fix a washer that won't start, drain, or fill with this electronic control board. Restores proper cycle management and operation. Moderate DIY repair.

This refrigerator ice level control board monitors ice production and storage levels in your automatic ice maker. It signals when to stop making ice when the bin is full and resume production when ice is needed. Replace this control board when your ice maker overproduces ice, fails to stop when full, or doesn't restart ice production when the bin empties.