Maytag Control Board

Dishwasher won't start or buttons not responding? This electronic control board manages cycle timing and operation. Most DIYers complete this repair in under 20 minutes.

Fix burners that won't ignite, slow clicking, or repeated sparking. This spark module controls ignition for gas range surface burners and oven.

The Coin Slide Interface is an OEM part for Whirlpool commercial washers. It is a component that allows users to insert coins or tokens to activate the machine and initiate the laundry cycle.

Causes of a faulty coin slide interface can include regular wear and tear, damage due to misuse or vandalism, or electrical component failure. These factors can result in issues such as coin rejection, incorrect coin counting, or the inability to start the machine using coins.

Symptoms of a Bad Part:

• Will not start
• Not washing properly
• Timer will not set

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Fix a non-cooling refrigerator, blank display, or non-dispensing ice/water. This electronic control board restores temperature and dispenser functions.

Compressor clicking on and off every 5 minutes? Freezer warming up? This inverter control board regulates compressor operation in modern refrigerators.

Fix cycles that won't advance or mixed-up wash settings with a new timer assembly. Moderately difficult repair taking 30-45 minutes with basic tools.

Fix refrigerator temperature issues, display failures, or defrost problems. This control board manages cooling cycles and temperature settings.

Oven not heating or display not responding? This electronic control board manages temperature, timing, and keypad functions. Moderate DIY repair.

Washer stops mid-spin or shows F6E1 error? The motor control board regulates drive motor speed and direction. Most DIYers replace it in 15-30 minutes.

Fix a refrigerator that won't cool, clicks repeatedly, or has a blank display by replacing the main electronic control board. Moderately difficult repair.

This is a high-quality refrigerator power supply board. It's an internal component that is made to control the refrigerator functions. This part is made with small precision parts to help with timing defrost and cooling cycles. This part can be damaged or malfunction and stop operating correctly. This may prevent the refrigerator from running, cause strange sounds, or cause the refrigerator to run at the wrong temperature.If this part is damaged, it will need to be replaced. Before replacing the power supply board, make sure the refrigerator is unplugged from the wall. The process will require a flathead screwdriver and a nut driver. Use the tools to unthread the screws on the access cover. Depress the retaining tab to remove the inner cover and disconnect the wires. Press the tab to release the power supply board and snap in the new component. Make sure the wires are properly connected and reassemble.This genuine OEM replacement part is sold on an individual basis. It is directly acquired from the manufacturer and is designed to be compatible with refrigerators made by Kenmore, Whirlpool, Maytag, and KitchenAid.

Microwave not heating or showing F1 E5 error? This inverter board converts voltage to power the magnetron. Requires tech sheet for testing procedures.

Fixes refrigerator not defrosting or freezer icing up. This adaptive defrost control board manages defrost cycles. DIY-friendly repair.

This defrost timer cam replaces the plastic cam on a mechanical defrost timer. It restores the timer's changeover between cooling and defrost, helping prevent frost buildup on the evaporator and temperature swings inside the refrigerator.

• Mounts on the timer shaft to actuate the internal switch between cooling and defrost
• Helps resolve issues like heavy frost on the evaporator, warm fresh food section, or a unit stuck in defrost/run
• Corrects timer advancement problems caused by a stripped, cracked, or missing cam
• Typically installed with the defrost timer in the control housing or rear service area

• Disconnect power before servicing
• Access the defrost timer and note the original cam's orientation for reference
• Remove any retainer, pull the old cam straight off, and press the new cam fully onto the shaft without forcing
• Reassemble, then manually advance the timer to confirm it switches modes before restoring power

Dishwasher won't start, lights blinking, or cycles not completing? The electronic control board manages all wash functions. Moderate DIY repair.

Fix an oven that won't heat, shows error codes, or has unresponsive controls. This main control board coordinates timing and powers key components.