Maytag Control Board

This is a refrigerator main control board. It manages and monitors the temperature settings of the appliance, including defrosting and cooling times. If the main control board is damaged or no longer working, the refrigerator or freezer could become too warm or cool, stop defrosting, or no longer start. In this situation, the part will need to be replaced.The only tool needed to replace the main control board is a flat blade screwdriver. First, make sure the refrigerator is unplugged to avoid it coming on during the replacement process. Next, two screws should be removed where the door closes before the light shield is taken off by pushing it to the back of the appliance. Find the access panel holding the main control board and apply pressure to pull it away. Free the pegs and move the hinges toward the front. Finally, install the connectors and take out the part before replacing it with a new component.This main control board is designed as an OEM replacement part sourced directly from the manufacturer. It is sold as a single component and fits several models of refrigerators from Ikea, Maytag, and Whirlpool.

The Inverter Box is an OEM component specifically designed for Whirlpool French door refrigerators. Located inside the refrigerator compartment top behind removable panels, the inverter box houses electronic components that control the compressor motor and refrigeration systems.

Causes of a bad inverter box include failure of internal circuit boards over several years of regulating refrigeration cycles or damage from liquid spills inside the unit.  

Symptoms of a bad inverter box include:

• Failure of the refrigerator section to adequately cool and maintain temperatures
• Erratic fluctuations in cold air dispensing from vents     
• Repeated triggering of defrosting modes unnecessarily 
• Inability to regulate between freezer and refrigerator settings

This Whirlpool replacement part is compatible with Maytag, Jenn-Air, Amana, Magic Chef, and Kenmore side-by-side refrigerators.
 

White

The Microwave Inverter Board is an OEM part for Whirlpool brand microwaves. This board works with the magnetron to convert voltage and power the cooking elements. 

Causes of a bad inverter board can include failure of electronics over time, shorts or current leaks, or improper installation.

Symptoms of a bad inverter board include:

• The microwave will not power on or heat food properly  
• Sparking or burning smells are detected inside the microwave cavity
• The display console does not illuminate or function correctly
• Error codes are frequently displayed

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models.

This keypad assembly is the touch-sensitive control interface for your appliance. It registers your button presses and relays them to the electronic control so cycles start, settings change, and the unit responds reliably to your commands.

• Provides the sealed touchpad/membrane switch that sends user inputs to the main control
• Failure may cause unresponsive or intermittent buttons, or only some keys working
• Can trigger random beeping or "stuck key" style error messages
• May prevent starting, stopping, or changing settings

• Disconnect power at the breaker before servicing
• Access the control console; carefully route and seat the ribbon cable—do not crease it
• Ensure connector tabs are fully latched and the cable is straight/aligned
• Reassemble and test all keypad functions before finalizing the repair

The Oven Control Board is an OEM replacement part for Whirlpool ovens. Includes overlay. This control board manages essential oven functions, including temperature regulation, bake and broil elements, and the display of time and settings. It serves as the central interface, ensuring precise operation of your oven.

Symptoms of a bad Oven Control Board include:

• The oven not heating properly or at all
• The display showing error codes or being blank
• Unresponsive buttons or controls
• Inconsistent cooking temperatures

Causes of a failing Oven Control Board can include power surges, overheating, or general wear and tear over time. Electrical component failures or damage to the circuit board can also render it inoperable.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This Electronic Control Board is the brain of your appliance, restoring dependable control of settings and functions. It interprets keypad and sensor inputs and directs power to components like motors, valves, heaters, fans, and lights for reliable operation.

• Manages timing and power to critical components based on user selections and sensor feedback
• Coordinates start/stop and cycle or mode execution for proper operation
• Common failure symptoms: unresponsive controls or display, won't start, cycles that won't advance, random beeping/error codes, or components not energizing
• Replaces a failed, shorted, or damaged control module to restore normal function

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the board by the edges and avoid touching circuitry
• Label/photograph wiring; move connectors one at a time and confirm secure seating and orientation
• Some models require configuration/programming after installation—follow the tech sheet inside the unit for any personality settings or diagnostics

This electronic control board is the appliance's central controller, interpreting inputs and switching power to components to run each cycle. Replacing a failed board restores responsive controls and reliable operation when the unit is unresponsive, erratic, or showing error codes.

• Coordinates timing and sequence of operations for the appliance
• Interfaces with user controls and display
• Sends power to motors, valves, fans, or heating elements as directed
• Typical failure signs: no response to controls, won't start/run, erratic or stuck cycles, recurring fault codes

• Disconnect power at the breaker or unplug before servicing
• Use ESD precautions; handle the board by the edges only
• Photograph connections and transfer wiring/connectors one at a time
• Ensure all harnesses are fully seated; follow the service sheet for any model-specific setup or configuration

This 5-button dispenser control board runs the refrigerator's ice/water dispenser user interface. Replace it to restore button response, indicator lights, and proper dispenser selections when the original board is unresponsive or erratic.

• Interprets dispenser keypad inputs and communicates selections to the appliance's control system
• Drives the dispenser panel's indicator lights and status feedback
• Coordinates ice and water dispensing functions based on user commands
• Common symptoms include no response to buttons, dispenser lights/indicators not working, inability to change selections, or intermittent/erratic UI behavior

• Disconnect power before servicing; use ESD protection when handling electronics
• Remove dispenser trim/panel to access the board; release locking tabs and unplug the wire harness
• Transfer any reusable overlay or mounting hardware from the original board if applicable
• Seat connectors fully, reassemble, and test dispenser functions before finalizing

Fixes refrigerator displays flashing, unit cycling on/off, or fans not running. This power supply board converts AC to DC for controls and components.

This electronic control board is the main control for the appliance's user functions and cycles, restoring electronic operation and programmed settings when the original board fails. Designed to replace a faulty or unresponsive control module. What it does:

• Receives input from the user interface and sensors to operate appliance cycles and features
• Controls timing, cycles, and relay signals to motors, valves, and heaters
• Can stop appliance functions or cause error codes when it malfunctions or loses power
• Commonly used to address unresponsive controls, incorrect cycle behavior, and intermittent operation

• Disconnect power to the appliance before attempting repair to avoid shock or damage
• Handle the board by the edges and avoid touching components or connectors to prevent electrostatic damage
• Verify connector fit and orientation before reconnecting; confirm all wiring matches original locations

This electronic control board regulates the appliance's console functions so cycles, settings and displays operate correctly. Replaces a faulty console module to restore responsive controls and normal cycle selection. What it does:

• Manages user inputs, cycle selection and timing signals for the appliance
• Controls display indicators, LEDs and electronic user-interface feedback
• Communicates with other modules to start/stop cycles and control features
• A failed board can cause unresponsive buttons, incorrect displays, or cycles that won't start

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle the board by its edges and avoid static discharge; use an anti-static wrist strap if available
• Verify the part number and appliance model match before installation

This control board kit replaces the appliance's main electronic control to restore normal cycle selection and responsive user controls. It provides the core logic and interface needed for timing, sensor response, and displaying status. What it does:

• Manages cycle timing, sensor inputs, and actuator commands to run selected cycles
• Processes user inputs from the console and updates the display/status indicators
• Helps resolve symptoms like unresponsive controls, missing display feedback, or intermittent cycle failures
• Works as the OEM-specified replacement logic module for affected control functions

• One control board kit as shown

• Disconnect power (and water/gas if applicable) before servicing to avoid shock or injury
• Handle boards by the edges and ground yourself to prevent ESD damage
• Follow the appliance's service manual for connector locations and mounting; retain all fasteners

Fix a dispenser that won't stop running or doesn't respond when pressed. This control board restores normal water and ice dispensing function.

This part is an control board that can be used as a replacement for a broken or malfunctioning control board in various washing machine models. This part ensures the washer functions, such as draining and filling, can be properly managed. In cases where the washer cannot be efficiently controlled, replacement will be immediately required. The control board will also need to be replaced if the user sees the F1 E1 error code. Before replacing this part, ensure the washing machine is unplugged from the power and water sources. Work gloves should be worn anytime a repair or replacement is attempted.This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. This part is suitable for use on a variety of washing machine models that have been manufactured by Whirlpool, Maytag, Jenn-Air, and Amana. It is a genuine OEM part and thus is manufactured from high-quality, durable, non-corrosive materials and is only sold individually.