Maytag Hinge Parts

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

Watched video from AppliancePartsPros.com, ordered part. I followed instructions on video and oven door works great now!!! Read more

• Door won't close

Replaced the hinge and receiver. Read more

The right door on our Jenn Air French Door Refrigerator would pop open & not fully close when the left door was closed first. Called the local distributor/dealer who advised me that the magnetic door gasket probably needed replacement (cost $300.00 + for the repair) What??? Visited you web site where I noted the right door had a "closure & bushing" on the bottom of the door. Could it be this was the problem fix? Took the right door off & examined both pieces. Sure enough the bushing was... Read more

Put the new hinges on the doors fyi you need to tell what size the screws are for the hinge kits would help a lot Read more

Replace two door hinges works great now. Read more

Purchased proper hinges. Lifted oven doors off the hinges. Removed screws securing the oven to the cabinet, then slid out the unit from the cabinet far enough to access the hinges. Then removed trim to better access the hinges. Then removed the screws holding the hinges. Then installed the new hinges, secured them with the screws, then reinstalled the trim, then slid the unit back into the cabinet, and secured it in place with the screws. Finally, I placed the oven doors back on my hinges. ... Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

Easy fix. Took two screws out of top door hinge. Lifted door off of bottom hinge. Laid door on blanket on floor. One cam part went on the hinge that was on the fridge, snapped in place. One cam part went on bottom of door, one screw to replace. Replaced door on bottom hinge then put top hinge back on. Job done. Read more

Watched a YouTube video. Read more

With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more

• Door won't open or close

I replaced the hinge due to the hinge spring breaking. To replace the hinge you do the following: 1. Disconnect power to stove, either at circuit box or at outlet. 2. Lift door off of outside hinge arms ; no screws are used to attach the door to the hinge 3. Remove two screw on under side of cook top, one on each side. 4. Disconnect cook top connector. 5. Lift cook top off 6. Remove screws from top rail of stove that hold the side panel. 7. Remove the screw on the back that hold the side... Read more

Looked up parts on internet using diagrams, ordered parts, they arrived in 2 days and installed them. Read more

Removed oven door. Removed front panel from oven door. Replaced both door hinges. Read more

• Lid or door won't close

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

Replaced both hinges. Easiest repair I’ve done on this unit. Took less than 20 minutes from start to finish. Read more