Screws, Nuts, Washers

Truss-head self-tapping screw for securing microwave panels, trim, and brackets. Replace lost or damaged mounting screws to restore fit.

These ceramic wire nuts provide secure electrical connections for range installation and wiring. The heat-resistant ceramic material protects connections from high temperatures generated during cooking. Use these nuts when installing a new range or repairing damaged electrical connections that have become loose or corroded.

Screws secure the burner base to your cooktop chassis for stable, safe cooking. Replace worn, missing, or damaged fasteners to restore proper alignment.

A stainless steel hex-washer-head screw used to secure panels and components on compatible appliances. Corrosion-resistant construction helps maintain a secure fit where short, strong fasteners are required. What it does

• Fastens appliance panels, trim, or brackets where an 8-18 thread and short 3/8" length are specified
• Hex washer head provides a larger bearing surface to reduce pull-through
• Stainless finish resists rust in humid appliance areas
• Common replacement when original mounting screw is stripped, missing, or corroded

• One stainless steel hex-washer-head screw

• Use the correct 8-18 thread fastener and do not force mismatched screws to avoid thread damage
• Tighten securely but avoid overtightening to prevent stripped threads or cracked panels
• Power tools may be used with appropriate bit, but start by hand to ensure proper alignment
• If installing near electrical components, disconnect power before servicing

Single replacement screw for securing dryer panels and internal components. Replaces lost, stripped, or damaged screws to restore proper fastening.

Stainless steel hex washer head screw for securing appliance panels, brackets, and trim. Replace missing, stripped, or corroded fasteners during repair.

Replace missing or stripped sheet metal screws on your washer pedestal. Secures panels, brackets, and components. Essential for rattling or loose parts.

1/4-20 hex washer head screw for washers. Secures panels, brackets, and internal components. Replace missing, stripped, or damaged mounting hardware.

Package of 12 screws with washers for securing washer panels, trim, and components. Replace missing, stripped, or damaged fasteners to restore fit.

Machine screw with 8-18 thread for securing panels, brackets, and components in disposers, ranges, ovens, microwaves, and hoods. Replace missing or stripped screws.

Replacement stringer bolt that secures the appliance's stringer or support rail to the cabinet frame, restoring panel alignment and preventing movement. Use when the original bolt is missing, loose, or damaged. What it does:

• Secures the stringer/support rail to the appliance frame so panels and assemblies stay aligned.
• Helps prevent cabinet or panel movement that can cause rattling or vibration during operation.
• Restores proper alignment when a loose or missing bolt causes misaligned panels or binding doors.
• Simple, direct replacement for a corroded, stripped, or lost fastener.

• Disconnect power before working on the appliance and remove any panels.
• Use the correct-size socket or wrench; hand-tighten, then snug—do not overtighten to avoid stripping threads.
• Inspect mating threads and replace the bolt if heads or threads are damaged; for the correct fastener location.

This replacement pan-head screw is used in refrigerators to fasten panels, brackets, and covers so they stay tight and properly aligned. Replace a missing or damaged screw to restore a solid, rattle-free fit.

• Secures interior/exterior panels, brackets, trim, and covers
• Replaces missing, stripped, or corroded hardware
• Helps maintain proper alignment of attached components

• Disconnect power before servicing; shut off water if working near water lines
• Match location to the original fastener and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal

• Thread size: #8-18 (type AB)
• Length: 1/2 inch
• Head style: Pan head, Phillips drive

This is a self-tapping mounting screw used to secure internal components such as basket slide rails, brackets, or panels inside the refrigerator or freezer compartment. It features an 8-18 thread size with a 7/16 inch length. Replace this screw if it has become stripped, lost, or corroded, causing parts inside the unit to feel loose or shift out of position.

Shoulder-style bolt that secures moving parts in refrigerator mechanisms. Replace if worn, damaged, or missing to restore proper alignment and smooth operation.

Machine screw for refrigerator panels, brackets, and assemblies. Replaces lost, stripped, or damaged fasteners to restore secure fit and stability.