Screws, Nuts, Washers

This SCR (silicon controlled rectifier) is a replacement power-control semiconductor used in appliance circuits to switch and regulate current. It restores proper control of heater/motor circuits when the original SCR fails. What it does:

• Controls current flow in high-power appliance circuits for timed heating or motor control.
• Replaces a failed SCR that causes intermittent or no power to the controlled component.
• Common symptom: appliance elements or motors do not turn on or cycle correctly.
• Common symptom: visible burn, cracking, or open circuit at the SCR.

• Disconnect power to the appliance before accessing electrical components to avoid shock.
• Handle the SCR carefully to avoid static or mechanical damage; use original mounting and hardware.

This is a 8-18 x 1/2 inch hex washer head screw used to secure appliance panels and components. It provides a reliable, corrosion-resistant fastener for repair or reassembly tasks. What it does:

• Fastens panels, brackets or trim where an 8-18 x 1/2" screw is specified
• Hex washer head offers wider bearing surface to prevent pull-through
• Stainless finish resists rust and corrosion in humid appliance environments
• Restores proper fit and function when original screw is missing or damaged

• One 8-18 x 1/2 in. hex washer head stainless screw

• Use the correct driver/socket to avoid stripping the head
• Tighten securely but avoid over-torquing to prevent damage to plastic or thin metal parts
• Disconnect power and follow appliance safety precautions before working inside the unit
• Replace only with the same size and head style for proper fit

This is a replacement ST4-16 sheet-metal mounting screw used to secure panels and small components on compatible appliances. It restores proper fit and prevents loose or rattling parts for a secure repair. What it does:

• Fastens trim, access panels, brackets and small components to appliance chassis
• Replaces missing, stripped or damaged screws that cause loose panels or vibration
• Provides correct thread and length for original mounting locations (ST4-16 size)
• Helps maintain safe, gap-free panel alignment for normal operation

• Use the same screw size and thread type as the original; do not over-torque
• If thread engagement is poor, inspect mating hole for damage before reuse
• Wear safety glasses and disconnect power to the appliance before working on panels
• If multiple screws are missing or hardware is corroded, replace all like-for-like fasteners

A replacement M12 x 25 flange bolt used to secure appliance components where a washer-style bolt head is required. Durable fastener that restores proper fit and helps stop movement or vibration in assemblies. What it does:

• Secures panels, brackets or assemblies that use an M12 flange-style fastener.
• Restores proper clamping force when an original bolt is stripped, corroded, or missing.
• Helps eliminate rattling, loose parts, or misalignment caused by a failed fastener.
• Works wherever a metric M12 x 25mm flange bolt is specified by the manufacturer.

• One flange bolt (M12 x 25)

• Disconnect power and follow manufacturer safety instructions before servicing.
• Use the correct socket or wrench to avoid rounding the head; tighten to the appliance manufacturer's torque specification.
• Inspect mating threads and replace if damaged; do not force a damaged bolt.
• If the OEM manual calls for threadlocker or a specific torque, follow those instructions.

Size: 8 - 18 ab.

This is a replacement 10-32 x 1 machine screw used to fasten appliance components. It restores secure mounting of panels, brackets and hardware so parts stay aligned and vibration or rattling is reduced. What it does:

• Secures panels, brackets, housings and small components to the appliance frame
• Keeps control boards, motors or assemblies held firmly in place
• Prevents loose parts that can cause vibration, noise or intermittent connections
• Matches the OEM thread and length for proper fit when replacing a worn or missing screw

• Disconnect power before working inside the appliance
• Use the correct 10-32 driver or bit to avoid stripping the head
• Thread into the original hole and tighten snugly; avoid over-torquing
• Replace with the same size and thread type to ensure proper fit and safety

This is a replacement 8-18 x 9/16 machine screw used to secure internal and external appliance components. It restores proper fastening and helps stop rattling or loose panels caused by worn or missing fasteners. What it does

• Secures panels, brackets, or small assemblies to prevent movement and vibration
• Replaces stripped, corroded, or missing screws that can cause rattling or misalignment
• Helps maintain electrical and mechanical connections by holding parts in proper position
• Appropriate where an 8-18 thread size and 9/16" length are required

• Replacement screw

• Disconnect power to the appliance before accessing internal components
• Use the correct driver to avoid stripping the screw head and ensure proper torque
• Do not overtighten; snug until secure to avoid damaging threads or parts

This replacement screw secures appliance brackets, panels, and components. It restores a tight, aligned fit when the original hardware is stripped, rusted, or missing, helping reduce vibration and rattling for reliable operation.

• Fastens brackets, panels, or mounts to keep components secure and aligned
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration, rattling, or loose/misaligned parts
• Matches original spec for reliable hold and fit

• Disconnect power before servicing; use proper PPE
• Match thread and length to the removed screw before installation
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Ensure parts are aligned and seating surfaces are clean before tightening

This small stainless fastener secures the door handle to the appliance. A worn or missing fastener can cause a loose, wobbly, or detached handle. Replacing it restores a solid, safe handle feel and appearance.

• Anchors the handle to its mounting point
• Helps correct a loose or shifting door handle
• Resolves rattling, gaps, or handle misalignment
• Stainless construction for corrosion resistance

• Disconnect power before servicing
• Protect the door finish with tape or a soft cloth near the work area
• Support the handle while removing and installing fasteners
• Do not overtighten; follow the product's service manual torque guidance

Replacement screw that secures panels and internal components, helping stop rattles and keep parts aligned. Use it to replace stripped, rusted, or missing fasteners and restore a secure fit. What it does:

• Secures panels, trim, or internal parts to prevent movement and vibration.
• Replaces worn, corroded, or missing screws that cause loose panels or rattling.
• Restores proper alignment for doors, covers, and mounted components.
• Provides a simple hardware fix that helps maintain safe, stable operation.

• Always disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head; apply firm but controlled torque.
• Verify screw length, head style, and thread type match the original before installation.
• If threads are damaged, replace with a matching OEM screw rather than over-tightening.

Package of 12

This hex washer head screw secures appliance components and hardware, helping keep panels and assemblies fastened for safe, reliable operation. Use it to replace missing or damaged screws that allow parts to shift or rattle. What it does:

• Fastens panels, brackets, and component assemblies using a hex washer head for broad bearing surface
• Restores secure fit where stripped, missing, or damaged screws cause loose parts or vibration
• Maintains proper alignment and prevents movement that can lead to noise or additional wear
• Matches the OEM thread and length for a correct fit when replacing the specific factory screw

• Disconnect power to the appliance before beginning any repair
• Use the correct hex driver/socket to avoid stripping the head
• Thread the screw in straight and tighten until snug; avoid overtightening
• Repair or replace the threaded insert or mounting hardware before installing

Hex washer head ,10-32 x 0.375. Ground

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

This replacement screw fastens panels, brackets, and internal components so assemblies stay aligned and tight during operation. With an 8-18 thread and 0.711-inch length, it matches the original hardware for a precise, reliable hold.

• Secures panels, brackets, and internal components to the cabinet/frame
• Replaces missing, stripped, or corroded screws
• Helps reduce vibration, rattling, and gaps from loose hardware
• Restores proper alignment after service or transport

• Disconnect power and shut off water/gas before servicing.
• Support panels/components while removing and installing the screw.
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten.

No.7 plastic .375