Terminal Block, Receptacle Parts

The Wire Harness is an OEM part for Whirlpool refrigerators. It is a critical component that contains all the wiring between electrical controls, motors, sensors, and other components inside the refrigerator. The wire harness allows communication and power transfer throughout the appliance.

Symptoms of a bad wire harness include:

• Lights or displays not working properly   
• The refrigerator not starting cool cycles or completing them
• Strange noises coming from motors or other areas  
• Error codes appearing on the control panel

Causes of a bad wire harness can include severed or damaged wires from normal wear and tear over time, improper installation, or exposure to moisture.

This OEM Whirlpool wire harness replacement ensures electrical signals are conducted smoothly throughout the refrigerator. It prevents disruption and allows for proper operation. This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This wire harness replaces damaged or burnt wiring to restore safe, reliable connections between the control and the components it serves. Install it when the original harness shows heat damage, broken conductors, or loose/brittle connectors.

• Carries power and signals between the control and connected components
• Replaces frayed, burned, or corroded wires and terminals
• Helps address intermittent operation, a non-working load (motor, pump, heater, fan), error codes for open/short circuits, or a burning odor
• Restores proper routing and insulation where the original harness was compromised

• Disconnect power before servicing; shut off water or gas if applicable
• Photograph routing and connections; move any clips/retainers to the new harness in the same positions
• Seat connectors fully without forcing; avoid pulling on wires or bending pins
• Route away from sharp edges and heat sources; secure with existing ties/retainers to prevent chafing

Replacement interior lamp assembly that restores illumination inside your refrigerator so you can see food and shelves clearly. Replaces worn or damaged light units to improve visibility and normal operation. What it does:

• Provides interior lighting so you can find items and check contents easily
• Replaces lamps that are burned out, dim, flickering, or physically damaged
• Sits in the appliance's existing lamp housing and works with the factory socket
• Helps maintain safe visibility when loading, unloading, or organizing the fridge

• Always disconnect power to the appliance before servicing to avoid shock
• Remove food and shelves as needed for safe access to the lamp housing
• Handle the lamp by the housing; avoid touching the light surface or bulb with bare hands

This block is a small mounting spacer used to secure and align components inside the appliance, helping maintain proper fit and operation. It replaces worn or broken mounting blocks to restore stable support and alignment. What it does:

• Provides a stable mounting surface or spacer between cabinet components
• Holds panels or assemblies in correct position to prevent rubbing or misalignment
• Helps reduce vibration or shifting of the connected parts during operation
• Commonly replaced when cracked, broken, or missing

• One mounting block

• High-level replacement; may require removing panels or trim to access mounting location
• Use appropriate hand tools and keep fasteners organized for reassembly
• Disconnect power before servicing any electrical components

For mating plug use 691707.

This fuse holder secures and connects a replaceable inline fuse to the appliance's electrical circuit, restoring overcurrent protection and helping prevent damage from short circuits or power surges. What it does:

• Holds and connects a replaceable fuse in the appliance's electrical circuit
• Completes the fuse's electrical connection so current flows through the protective element
• Replaces a cracked, burnt, or loose holder that causes intermittent power or blown fuses
• Helps restore proper overcurrent protection when the fuse itself is intact

• Disconnect power to the appliance before inspecting or replacing electrical parts.
• Inspect nearby wiring and connectors; replace any damaged components to ensure a secure connection.

This fuse block is the appliance electrical terminal used to secure and connect a fuse or wire harness, restoring a safe electrical path for heating and motor circuits. It helps maintain reliable power transfer inside the appliance. What it does:

• Provides a secure mounting point and electrical connection for a fuse or inline connection
• Enables proper power flow between the control and high-voltage components
• Can cause loss of power, intermittent operation, or heating issues when damaged or corroded
• Replaces a worn, cracked, or melted terminal block to restore safe connections

• Disconnect power to the appliance before starting any work
• Handle wiring carefully; secure all splices and fasteners to manufacturer torque recommendations

2 wire insulator.