Heating Element

This 20-inch bake element heats the bottom of the oven cavity so food cooks and browns evenly. Replacing a failed element restores proper oven heating and baking performance. What it does

• Heats the oven's bake chamber during bake cycles
• Replaces a cracked, burned-through, or non-heating bake element
• Helps resolve symptoms like no heat from the bottom, uneven baking, or oven failing to reach set temperature
• Works with the oven's control and safety circuits to provide consistent heat

• Disconnect power to the appliance at the breaker or unplug before starting
• Access usually requires removing the oven cavity bottom or back panel
• Handle the element by its insulated areas and avoid bending or touching the bare heating surface
• Tighten terminal connections securely and verify operation with the oven empty after reassembly

The Surface Element (240V-2100W) is an OEM part for Bosch cooktops and ranges. It provides consistent, even heating from below pans on the cooktop surface.

Causes of a bad surface element can include normal wear and damage from extended, heavy usage. Food or liquid spills left on the element for prolonged periods could potentially corrode the coils or electronics over time as well.

Symptoms of a bad surface element include:

• Element not heating up at all or heating unevenly
• Element heating intermittently or stopping prematurely
• Buzzing, clicking or smoke coming from below the element
• Tripped or blown circuit breakers when using that element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Burner not heating or won't turn on? This 12-inch halogen element restores radiant heat to your cooktop. Common DIY repair with basic tools in 30 minutes.

If your cooktop burner won't heat or stays on high, this surface heating element may need replacement. Moderate DIY repair with basic tools.

Broiler not heating or browning food properly? This upper oven broil element restores high-heat broiling for searing and finishing. Easy DIY fix.

This oven bake element heats the oven cavity so food cooks and bakes properly. Replacing a worn or broken element restores consistent heat for even baking and broiling. What it does:

• Converts electrical power into heat to warm the oven interior during bake and broil cycles
• Replaces a damaged or open element that can cause the oven to not reach temperature or cook unevenly
• Works with the oven's control system to provide steady, distributed heating
• Common symptom: oven won't heat, heats very slowly, or produces uneven cooking results

• Disconnect power at the breaker before starting any repair
• Allow the oven to fully cool and wear gloves to protect against sharp edges
• Remove the oven bottom or access panel as required, disconnect element wiring, and secure the replacement element in the original mounting
• Reconnect power and perform a short test bake to ensure proper operation

This bake element is the oven's primary heating element for baking and roasting, restoring proper oven heat so food cooks evenly. It replaces a damaged or worn element to bring back reliable bake performance. What it does

• Heats the oven cavity during bake cycles to provide consistent cooking temperatures.
• Commonly linked to symptoms like an oven that won't heat, takes too long to preheat, or produces unevenly cooked food.
• Visible damage (breaks, blisters, or heavy corrosion) or open electrical continuity are signs this element needs replacement.
• Works with the oven's control and safety systems to cycle heat as required.

• One bake element

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Allow the oven to cool completely and handle the element carefully to avoid sharp edges.
• Inspect wiring and terminal connections; replace any damaged connectors before reassembly.
• After installation, restore power and run a short bake cycle to ensure proper operation.

This bake element heats the oven's lower chamber so food and bake cycles reach cooking temperatures. Replace a damaged or non-heating element to restore even baking and proper oven operation. What it does

• Converts electrical power into heat for the oven's bake cycle.
• Heats the oven's lower cavity to maintain set cooking temperatures.
• Commonly replaced for symptoms like no heat, weak heat, or uneven baking.
• Works with the oven's controls and sensors to deliver consistent bake performance.

• Disconnect power to the range at the breaker before starting any work.
• Allow the oven to cool completely and wear gloves to protect against sharp edges.
• Remove the oven racks and detach mounting screws and wire connectors to replace the element.
• Only reconnect power after the element is secured and wiring is reattached; test on a short bake cycle.

This round cooktop surface element provides a direct heat source for electric ranges, restoring one burner's ability to heat cookware evenly. It's a straightforward replacement for a damaged or non-heating burner element. What it does:

• Heats cookware on an electric range cooktop so pots and pans can reach cooking temperatures
• Replaces a cracked, burned-through, or non-functioning surface element to restore burner operation
• Helps eliminate intermittent or no-heat symptoms on the affected burner
• Works with the range's existing terminal block and controls when compatible

• One cooktop surface (round) element

• Disconnect power to the range at the circuit breaker before starting work
• Remove the damaged element from its terminal connections and lift out; install the new element by seating terminals fully and testing power
• Use care to avoid scratching the cooktop surface and verify element compatibility with your model

This heater assembly replaces the dryer's heating unit to restore normal drying performance and consistent drum temperatures. It's a direct-fit replacement designed to match the OEM heater layout and electrical connections. What it does:

• Reheats incoming air so the dryer can remove moisture from clothes.
• Works with the dryer's blower and thermostat to maintain operating temperature.
• Commonly used when the dryer produces little or no heat, or runs long cycles.
• Helps resolve intermittent heating caused by a failed heating element or broken heater housing.

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Access requires removing the dryer cabinet or rear panel; follow OEM disassembly steps.
• Inspect related parts (thermal fuse, high-limit thermostat, wiring, connectors) for damage while replacing the heater.

Oven not heating or baking unevenly? This lower bake element restores consistent bottom heat for proper baking temperatures and even cooking results.

Burner not heating? This cooktop surface heating element restores your cooking surface. Direct replacement for compatible electric cooktops.

This heating element warms the appliance's wash/dry cycle to help heat water and support drying for better cleaning results. It replaces a failed or weakened heater to restore normal heating performance. What it does:

• Heats water and supports drying during wash cycles.
• Restores lost heating when the appliance no longer reaches proper wash or dry temperatures.
• Can correct symptoms such as poor cleaning, incomplete drying, or heater-related error codes.
• Works as the main heater assembly responsible for thermal functions in the tub.

• Disconnect power and water before starting any repair.
• Access may require removing lower panels or the tub assembly; follow service instructions.
• Handle carefully to avoid bending terminals or damaging mounting points.
• Test the new element for continuity and correct installation before reassembling the appliance.

Burner not heating or heating unevenly? This surface element provides direct heat to cookware. Common DIY fix when element shows visible damage.

The Coil Surface Element is a 6-inch OEM part for Whirlpool ranges. It is responsible for radiating heat from its coils to cook food positioned above the stovetop grates. 

Symptoms of a faulty coil surface element include:

• Slow or uneven heating of pots and pans  
• Hot and cold spots on cooking surfaces
• Element coils glowing dimly or not at all
• Buzzing or crackling noises coming from below cookware

Causes can be mineral deposits coating the coils over time, physical damage like bending or breaks, or standard wear of heating filaments inside. 

This genuine OEM Whirlpool part is also compatible with the electric ranges of Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and Kenmore brands.

Burner won't heat or randomly stays on? This range heating element restores proper burner function. DIY repair takes about 30 minutes with basic tools.