Washer Dryer Combo Gasket & Seal

Seals front and rear tub halves to prevent water leaks. Replace if you notice leaking during wash cycles or after bearing repair. Verify fit with your model.

Drum glide supports the front of your dryer drum for smooth rotation. Replace when you hear scraping or squeaking sounds. Confirm fit with your model.

The Door Gasket is an OEM part for GE dryers. This seal prevents hot air from escaping during a cycle, ensuring that the dryer operates efficiently and safely. The gasket's primary role is to maintain the internal temperature and airflow, which are essential for the drying process.  

Causes of damage to the door gasket often involve regular wear and tear from opening and closing the dryer door.  

Symptoms of a bad Door Gasket include:

• Clothes taking longer to dry or not drying fully due to heat escaping from the dryer.
• An increase in energy consumption as the dryer works harder to maintain the required temperature.
• Visible wear, tears, or gaps in the gasket 
• Heat leakage from around the dryer door 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

Seals the lower dryer door to prevent heat loss and ensure efficient drying. Replace if worn, cracked, or air is escaping. Verify fit with your model.

Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.

Replacement dryer seal creates a tight barrier between components to prevent leaks and lint buildup. Replace when worn or brittle to stop drips. Verify fit.

Seals the blower housing to prevent air leaks and maintain efficient airflow. Replace if torn, damaged, or causing reduced drying performance.

The washer water inlet filter is a small mesh screen that sits at the water inlet valve connection point and catches sediment, debris, and mineral particles from your home's water supply before they enter the machine. Keeping this filter clear ensures proper water flow into the washer. Replace this part if your washer is filling slowly, not filling at all, or if the existing filter is torn, corroded, or too clogged to be cleaned effectively.

This is a rubber lip seal that fits around the upper portion of the washer's basket drive tube, preventing water from leaking past the shaft and into the transmission or bearings below. It creates a watertight barrier between the wash tub and the drive mechanism. Replace this seal if you notice water leaking from beneath the washer tub, hear grinding noises during the spin cycle, or find oil residue under the machine.

Secures and seals your washer's drain hose connection to prevent leaks. Replace if cracked, brittle, or leaking. Confirm fit with your model number.

Replaces worn or torn door boot gasket that seals your washer drum. Replace if you notice water leaks, mold buildup, or visible cracks. Confirm fit.

This is an oil seal that fits around the transmission shaft where it enters the gear case on a washer or laundry center. It prevents water from leaking into the gear case and keeps lubricating oil from leaking out. Replace this seal if you notice oil leaking from the bottom of the washer, water entering the transmission, or if the unit is making grinding noises during the agitate or spin cycle.

Seals your dryer door to prevent heat loss and improve drying efficiency. Replace if torn, cracked, or no longer sealing properly. Confirm fit with your model.

Washer tub gasket seals the outer tub to prevent leaks. Replace if you notice water pooling under your washer. Confirm fit with your model number.

Stabilizes the drum and reduces friction for smooth rotation. Replace when you hear rubbing noises or notice uneven drum movement. Verify fit with your model.