Washer Dryer Combo Gasket & Seal

This ring drain hose is the replacement drain tube that routes and removes water from the appliance, restoring proper drainage and preventing leaks or standing water in the wash area. Designed to match the original fit and function. What it does:

• Channels wastewater from the tub/pump to the household drain to maintain normal drain cycles
• Restores proper drainage when the original hose is cracked, kinked, or leaking
• Helps prevent leaks and water damage caused by failed or deteriorated hoses
• Compatible with compatible stock mounting points for a like-for-like replacement

• One ring drain hose (1 piece) as pictured

• Disconnect power and water supply before servicing to avoid shock or flooding
• Inspect adjoining clamps and fittings; replace clamps if corroded or damaged for a secure seal
• Ensure hose routing is free of sharp bends or kinks and is secured per the appliance's service instructions

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

This tub seal assembly keeps the washer's inner tub sealed around the drive shaft to help prevent water leaks and contain wash water. It replaces a worn or damaged tub seal to restore a watertight fit. What it does

• Seals the gap between the inner tub and the transmission/drive shaft to reduce leaks
• Helps prevent water from entering the transmission area and causing damage
• Commonly replaced when you notice water on the floor or pooling under the washer
• Used when the existing seal is cracked, torn, or excessively worn

• One tub seal assembly

• Disconnect power and shut off water before starting any repair
• Replacement typically requires partial disassembly of the washer (cabinet or front panel removal) and access to the tub/transmission area
• Inspect shaft and surrounding surfaces for wear or damage and clean mounting surfaces before installing the new seal

This tub seal kit replaces a worn or damaged tub gasket to restore the appliance's watertight seal and reduce leaks. It's a direct-replacement style kit used during tub or pump repairs to help maintain proper sealing. What it does:

• Replaces the tub sealing components that prevent water from escaping the tub area
• Helps stop common leak symptoms like puddling or water on the floor near the appliance
• Restores a secure seal after tub or pump disassembly to reduce moisture-related damage
• Useful when service shows visible gasket wear, cracks, or hardening

• Disconnect power and water supply before starting any repair
• Drain the appliance and remove any obstructing panels to access the tub area
• Follow the OEM service manual for disassembly and correct seal orientation

This rubber agitator cap seal creates a watertight barrier at the base of the washer agitator to help prevent leaks and keep the transmission area dry. It's a simple replacement that restores proper sealing around the agitator. What it does:

• Seals the agitator base to reduce water entering the transmission and cabinet area
• Helps prevent leaks that can cause rust, puddling, or damage under the washer
• Keeps contaminants and detergent residue out of the gearcase area
• Supports consistent wash performance by maintaining a dry drive assembly

• Disconnect power and turn off the water supply before starting any repair
• Remove the agitator cap and agitator per your model's service instructions to access the seal
• Inspect surrounding parts (agitator cap, agitator, and shaft) for wear and clean mating surfaces before installing the new seal

This door gasket creates a tight seal around the refrigerator door to help maintain proper cooling and reduce energy loss. Replacing a worn gasket restores a full seal for better temperature control and food preservation. What it does:

• Seals the door to prevent warm, humid air from entering the refrigerated compartment
• Helps reduce frost buildup and keeps interior temperatures stable
• Improves cooling efficiency and can lower energy use caused by a leaking seal
• Stops odors and moisture transfer between the fridge interior and kitchen

• Unplug the refrigerator before starting and remove any food or shelves blocking the seal.
• Work slowly to avoid stretching or creasing the gasket; follow door-hinge or trim removal steps if needed.
• Inspect the door flange for damage and clean the mating surface before installing the new gasket.
• After installation, allow the gasket to seat fully and check for uniform contact around the door; warm-up or seating time may be needed.

This oven door gasket provides a replacement seal that helps keep heat and cooking odors inside the oven for consistent cooking and improved efficiency. It restores a tight seal where the door meets the oven cavity. What it does:

• Replaces a worn, torn, or brittle door gasket to reduce heat loss and hot spots
• Helps the oven reach and maintain set temperatures more consistently
• Minimizes smoke, burning smells, and excess energy use caused by leaks
• Improves cooking performance by restoring a proper seal around the door

• One oven door gasket

• Disconnect power to the range/oven before beginning any repair
• Allow the oven to cool completely; remove the oven door per the manufacturer's instructions if required
• Gasket typically attaches by pushing into a channel around the door or oven frame; use a non-marring tool if needed
• Follow OEM instructions for reinstallation and torque recommendations