Washer Hose Or Tube

This water inlet pipe routes water from the refrigerator's supply to the dispenser and ice-making system, helping restore proper water flow and stop leaks at the inlet tubing. Durable molded tube designed to match factory fit. What it does:

• Carries water from the household supply to the fridge's dispenser and ice maker
• Replaces cracked, pinched, or corroded inlet tubing that can cause leaks
• Restores water flow when a damaged inlet pipe prevents dispensing or ice production
• Matches OEM shape to align with mounting points and fittings

• Turn off and disconnect power to the appliance before servicing.
• Shut off the water supply and drain remaining water from the line before removing the old pipe.
• Inspect and replace any worn seals, clips, or fittings; tighten connections to OEM torque specifications.

This inlet hose connects the home water supply to the appliance so it can fill properly. It replaces a worn or leaking supply hose to restore safe, reliable water flow for normal cycles. What it does:

• Directs incoming water from the household supply to the appliance inlet valve
• Works with the appliance's inlet valve and fittings to allow proper fill and rinse actions
• Commonly replaces hoses that leak, spray, kink, or block water flow
• Helps stop slow fills or intermittent filling caused by damaged or deteriorated hoses

• One inlet hose

• Turn off water supply and disconnect power before starting work
• Inspect and replace any damaged O-rings or fittings; use approved replacement fittings if needed
• Hand-tighten connections, then snug with a wrench—avoid over-tightening to prevent damage
• After installation, restore water and power, run a short fill cycle, and check all connections for leaks

This pressure switch hose connects the washer tub to the pressure/air switch so the machine can detect water level accurately. Replacing a cracked or clogged hose restores reliable level sensing and reduces false error codes. What it does:

• Carries air pressure from the tub to the pressure/air switch so the control can sense fill level
• Prevents false water-level readings caused by cracks, clogs, or leaks in the hose
• Helps stop overfilling, underfilling, excessive agitation, or frequent cycle interruptions
• Works with the washer's pressure/air switch assembly to maintain proper cycle operation

• Disconnect power and turn off the water supply before starting any repair
• Install hose to same routing and fittings; ensure tight, secure connections at both ends
• Avoid kinks, sharp bends, or pinches that can block air flow or cause leaks
• After installation, run a test fill/drain cycle to confirm correct operation and no leaks

This inlet hose connects the household water supply to the appliance's steam generator, allowing steam cycles to produce moisture for cleaning or sanitizing. Replacing a damaged inlet restores proper water flow to the steam system. What it does

• Channels incoming water to the steam generator assembly so the unit can produce steam.
• Stops steam or steam-cycle operation when cracked, pinched, or leaking.
• A leaking or split inlet hose can cause visible water under or behind the appliance.
• Faulty inlet hose may trigger steam-related fault/error indications or interrupted steam cycles.

• One hose inlet for the steam generator assembly.

• Turn off water supply and disconnect power before servicing.
• Inspect and replace any worn seals or O-rings; ensure fittings are seated and tightened to OEM torque specs.
• Use only the exact replacement part number to ensure proper fit and function.

This hose overflow kit redirects excess water from the refrigerator's drain area to the drain pan, helping prevent puddles and water damage behind or under the appliance. Fits common GE refrigerator drain/overflow applications. What it does

• Provides a dedicated path for excess defrost and condensation water to the drain pan
• Helps stop water pooling under or behind the fridge that can indicate a blocked or misrouted drain
• Useful when replacing a cracked, split, or missing drain/overflow hose
• Restores proper water routing after service to the defrost drain or water system

• One hose overflow kit

• Disconnect power and shut off the water supply before starting service
• Route hose from the drain/overflow outlet to the drain pan following OEM routing; secure with supplied clamps or retainers
• Inspect or replace any related grommets or seals to ensure a watertight fit
• Test for proper drainage and check for leaks after restoring power and water

This outside drain hose directs wastewater from your washer to the household drain. Replace a cracked, kinked, or leaking hose to stop leaks and restore reliable draining at the end of each cycle.

• Routes discharge water from the drain pump to a standpipe, laundry tub, or sink
• Helps maintain proper flow during drain/spin to prevent backups
• Common signs of failure: water leaking behind the washer, slow or incomplete draining, or drain-related error messages
• Visual clues include cracks, pinholes, bulges, or severe kinks

• Disconnect power and water; pull the washer forward for access and place towels/bucket as needed
• Note hose routing and connection points; release clamps and remove the old hose
• Fully seat the new hose; reuse existing clamps/hangers as required. Route without kinks and maintain proper standpipe height
• Run a test drain/rinse and check all connections for leaks

This water inlet hose directs incoming water into the appliance for normal operation, providing a reliable pathway that maintains safe, consistent water flow. Use this OEM-fit hose to replace a cracked, leaking, or damaged inlet line. What it does

• Carries incoming water from the home's supply to the appliance's water valve or fill assembly.
• Restores proper filling when an old hose leaks, is split, or becomes deteriorated.
• Helps prevent water damage and maintains normal cycle performance when functioning correctly.
• Compatible with repairs where the original inlet hose is worn, kinked, or blocked.

• One new replacement water inlet hose.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect hose fittings and seals; replace any worn clamps or gaskets for a secure, watertight connection.
• Route the hose without sharp bends or kinks and secure per the appliance's routing clips.

This hose connector joins a refrigerator's/dispenser's water line to internal plumbing, restoring a secure, leak-resistant connection. It replaces cracked or worn connectors to help stop leaks and ensure reliable water flow. What it does:

• Provides a sealed connection between the water hose and the appliance plumbing or valve
• Stops leaks caused by cracked, brittle, or damaged connectors
• Restores proper water flow to the dispenser/ice maker when the connector is the failure point
• Works with hose clamps or fittings already present in the appliance plumbing

• Shut off water supply and unplug the appliance before servicing
• Inspect hose ends and replace clamps or O-rings if damaged; use proper-size clamps for a secure fit
• Hand-start threads, then tighten snugly—avoid over-tightening plastic fittings to prevent damage
• Turn water back on and check thoroughly for leaks after installation