Washer Support Parts

The Shock Absorber is an OEM part compatible with Whirlpool washing machines. It is a crucial component that helps reduce vibrations and dampens movement during the spin cycle. The shock absorber absorbs mechanical stresses to prevent the washer tub, suspension springs, and other components from wearing out prematurely.  

Causes of a bad shock absorber include wear and tear over time, cracks or breaks from heavy loads, or damage due to impact.  

Symptoms of a bad shock absorber include:

• Excessive shaking, vibration or noise during the wash and spin cycles   
• The washer walking or moving during operation
• Premature failure of other suspension parts like springs or the washer frame
• Potential leaks if movement stresses plumbing connections

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Shock absorber that cushions vibrations during spin cycles. Mounts between the drum and base. Replace if cracked, leaking, or worn to restore stability.

Replaces broken or worn washer shock absorber that controls tub movement during spin. Installs on washer suspension to reduce vibration and shaking.

Suspension damper shock absorber for front-load washers. Replaces cracked, weak, or broken shocks causing excessive vibration and off-balance loads.

Reduces drum vibration during spin cycles. Replace if washer shakes excessively or drum moves too much. Mounts between drum and base. Sold individually.

This friction damper assembly adds controlled resistance to a door or panel so it opens and closes smoothly. Replacing a worn damper helps prevent sudden drops or slamming and restores a solid, quiet feel to the motion. What it does:

• Provides controlled friction to the hinge mechanism for smooth, damped movement
• Works with the hinge system to help balance door/panel weight
• Reduces slamming and impact, improving overall feel and sound
• Symptoms include the door dropping open quickly, slamming, uneven/loose motion, or clicking/squeaking near the hinges

• 1 friction damper assembly

• Disconnect power to the appliance before servicing
• Access the hinge/damper mounting area per your model's service documentation
• Support the door/panel during removal and match the original orientation and hardware
• After installation, cycle the door open/closed to ensure smooth, balanced motion before reassembly

Damper assembly mounts to the washer base to support the drum and reduce vibration. Replace if cracked, broken, or worn to restore stability.

Includes suspension pads.

This washer shock absorber mounts between the outer tub and base to control movement during spin. Replacing a worn damper restores stability, reduces vibration and noise, and helps prevent the machine from walking or banging.

• Stabilizes the tub during spin by absorbing and controlling movement
• Reduces vibration and cabinet noise for smoother operation
• Helps the washer reach and maintain proper spin speed
• Worn shocks can cause shaking, banging, or walking during spin

• Disconnect power and water; use gloves and protect the floor.
• Access from the front or rear depending on model; remove panels as needed.
• Support the tub, then remove fasteners at both ends; install the new damper in the same orientation and tighten securely.
• Reassemble, level the washer, and run a test spin to check for vibration.

Spider arm connects the wash basket to the drive shaft in front-load washers. Replace if cracked, corroded, or broken to restore proper basket support.

Mounting bracket that secures and stabilizes internal washer components. Replace if broken, cracked, or damaged to restore proper panel alignment.

Trunnion shaft kit for laundry center washers. Replaces worn, damaged, or broken trunnion shaft assembly. Essential structural component for drum support.

Connects the washer's inner drum to the drive assembly. Replace if cracked, damaged, or worn to restore drum stability and eliminate wobbling or noise.

This 22-inch strap snubber cushions and guides the dryer belt at the front of the drum to help reduce noise and prevent premature belt wear. It restores proper belt routing for smoother, quieter tumbling in compatible Whirlpool dryers. What it does:

• Cushions the belt where it contacts the front drum area to reduce rubbing and chafing.
• Helps maintain correct belt routing and tension to prevent slipping and uneven drum rotation.
• Can reduce squeaks, squeals, and jerky drum movement caused by a worn or broken snubber.
• Protects the belt from premature wear that may lead to fraying or failure.

• Disconnect power (and gas supply for gas dryers) before beginning any repair.
• Access typically requires removing the dryer front panel or drum—follow the OEM service manual for safe disassembly.
• Inspect the drive belt, idler pulley, and drum rollers when replacing the snubber; replace any worn parts.
• Wear gloves and eye protection.

This shock dampener replaces a worn suspension shock to help steady the washer tub and reduce vibration and banging during cycles. Fits common GE top-load washer suspension systems for stable operation. What it does:

• Absorbs and dampens tub movement to reduce vibration and loud banging
• Helps keep the drum aligned during spin and rinse cycles
• Reduces washer "walking" or shifting across the floor
• Restores smoother, quieter operation when original shocks are failing

• One washing machine shock dampener

• Disconnect power and water supply before beginning any repair
• Support or secure the tub before removing the old shock to prevent sudden movement
• Inspect mounting pins/bushings; replace any damaged hardware for proper fit

Inner tub hub plate mounts inside your washer drum. Replace if cracked, damaged during clutch repair, or frozen onto the pulsator assembly.