Need Help?
Call
This electric pump is responsible for draining water out of the washer tub during the drain and spin cycles. It pumps used wash and rinse water through the drain hose and out of the machine. Replace this pump if your washer fails to drain, drains slowly, makes loud humming or grinding noises during the drain cycle, or if you find water remaining in the tub after a completed cycle.
Very simple repair really. Unplugged the washer, moved the washer in order to have access to the back panel. Remove 13 #20 torx screws holding the back panel on ; then removed back panel. Open the filter access on the front bottom of the washer to drain any remaining water, be sure to have a towel ready, as if the pump is bad, there's bound to be quite a bit. Looking at the washer from the back, the bottom left contained the pump. Remkve the two electric connectors and move out of the way.... Read more
Fix drainage issues and trapped debris with this washer drain pump filter. Traps lint and particles for optimal performance. Includes video guide.
When we first removed the drain filter from the washer, we noticed the O-ring had a slight defect which made removal hard and reinstallation almost a nightmare. Finally we ordered another filter when we ordered a water valve/thermistor for the mother-in-law's washer. Filter installed a lot easier than the original one. Should have ordered one way sooner! Now on to the washer. Read more
Fix a washer that won't drain or leaks during the drain cycle. This pump and hose assembly restores water removal. Direct-fit installation for most models.
Replaced the pump. Read more
Fix washer leaks and drainage issues with a new water pump. Common when water leaks during drain cycle or won't pump out. DIY-friendly replacement.
Turned my washer over and the pump was right there at the bottom didnt even need any tools, it had a kids sock stuck in it, I could not unjam it so I got this new pump, you just take the old one out and put the new one in Read more
The DRAIN PUMP is an OEM component specifically designed for GE washers. It is located near the base of the unit and functions to remove water from the wash tub at the end of cycles. The drain pump works vigorously to expel soiled water through the drain hose for hygienic cleaning.
Symptoms of a bad drain pump include:
Causes can include internal blockages from built-up debris, wearing of impeller seals or motor, or physical damage impairing pump functionality.
Replace yours today with this genuine OEM GE part for thorough water extraction and machine drainage after every load. This GE replacement part is compatible with Hotpoint, RCA, and select Kenmore models.
Washer won't drain or leaves standing water after cycles? This drain pump removes water from the tub. Common repair that restores proper drainage.
This pump and brake assembly drains water from the tub and applies the basket brake in your top-load washer. Replacing a worn assembly restores proper draining and a safe, prompt basket stop between cycles. What it does
Upon opening the front cover of my GE washing machine, I found the water pump/brake was not spinning as it should when the drain/spin cycle was starting. I suspected that the pump/brake was the cause of the problem. I tried to turn the flywheel of the pump by hand and found it tight and somewhat difficult to turn. To temporarily fix the problem, I added a couple drops of motor oil to the front shaft and bearing to see if it would loosen up a little bit. Doing that and turning the flywheel by... Read more
Fix a washer that won't drain or spin with this drain pump. Common repair for water remaining in tub after cycle. Moderate DIY repair effort.
Ordered a replacement. Had to tip washer toward the back to provide access underneath to the pump. Had some difficulty removing the two hose clamps. Pliers were not the best tool. Had to ensure the drive belt was properly engaged with the pulley of the pump. Read more
Washer won't drain or leaves water in the tub? This drain pump assembly removes water during the drain cycle. Moderate DIY repair, 30-45 minutes.
This drain pump kit includes the pump assembly and associated seals needed for a complete replacement. The drain pump removes water from the wash tub during the drain and spin cycles. Replace this kit if your washer fails to drain, drains slowly, makes loud humming or grinding noises during the drain cycle, or leaks water from the pump area.
After ordering two pump kits and thinking I had still had the wrong pump I read how other customers fixed the problem. Forget about the pump going back in the same location. It mounts to the bottom of the frame not to the bottom of the tub as it came from the manufacturer. In my case there were mounting holes already there to accept the new pump bracket. The new hoses will reach the bottom of the tub and outlet. Fast and easy repair once I sorted through the changes. I hope other Samsung... Read more
Fixes washers stuck mid-cycle with standing water or not draining. Restores normal draining and cycle completion. Straightforward DIY replacement.
Ordered pump, popped it in. Hardest part was walking down the stairs Read more
This is a replacement washing machine drain pump assembly that removes water from the tub so your washer can drain and spin properly. Fits common GE top- and front-load designs and restores normal draining performance. What it does:
Ordered new pump from you guys. Used the old steel bracket, affixed new pump and attached assembly to washer. No leaks now. Thank you! Read more
Fix F9/E9 error codes or washer won't drain issues with this drain pump assembly. Removes water during wash and spin cycles. DIY repair takes 30 minutes.
Removed the entire front panel to get at pump was not bad took about 10 mim to remove 10 minutes to change pump and 10 minutes to put the hole thing back together The hardest thing was that the retaining ring on the rubber door seal Read more
Usually ships within 4 - 14 days
Fixes 'ND' error code and washer won't drain issues. This drain pump assembly restores proper water removal. DIY-friendly repair, typically done in 1-2 hours.
The machine was displaying an "nd" code, wasn't draining, and would make a grinding noise when the pump ran. After about 30 seconds of the grinding noise, the pump would stop, and the washer would pause the load. Diagnosis was fairly easy: I drained the water out manually at the filter housing. (If you have a drain in the floor of the laundry room, and the washer is up-slope from the drain, just drain it onto the floor and into the drain.) Next, leaving the drain filter out, I started the... Read more
Fix a washer that won't drain or shows error codes E03/E04. This drain pump removes water after each cycle. Moderate DIY repair with basic tools.
Replaced with part ordered. Exact fit. No problems. Thank you Appliance Parts PROS! Read more
Fix a washer that won't drain or leaves standing water with a new drain pump assembly. Moderately challenging repair that solves drainage issues.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.