Accessories

This nozzle connector links a water hose to the washer's nozzle/dispenser assembly, creating a tight, leak-resistant connection. Replacing a worn connector helps stop leaks and restores consistent water flow during fill and spray functions. What it does:

• Couples the hose to the nozzle/dispenser assembly and maintains a watertight seal
• Directs water into the dispenser or tub as designed
• Typical failure symptoms: leaks near the top panel or dispenser, loose hose, weak or erratic spray/fill
• Cracking, hardening, or deformation can lead to drips and connection issues

• 1 nozzle connector

• Disconnect power and shut off water supplies before servicing
• Remove the top cover to access the dispenser/nozzle area; protect the work area with a towel
• Release hose clamps, seat the hose fully on the new connector, and secure clamps firmly
• Run a brief fill/rinse to check for leaks before reassembly

This faucet adapter threads onto a compatible sink faucet to provide the connection point for an appliance's quick-connect hose, creating a secure, watertight hookup during filling and operation. What it does:

• Adapts faucet spout threads to accept the appliance hose/coupler
• Helps prevent leaks and drips at the faucet connection
• Replaces a worn, stripped, or missing adapter
• Common fix when a quick-connect hose (e.g., on a portable appliance) won't attach or pops off

• 1 faucet adapter

• Turn off water and remove the existing faucet aerator before installing
• Hand-thread the adapter carefully to avoid cross-threading; snug gently if needed with a non-marring tool
• Attach the hose/coupler and slowly open the faucet; check for leaks and retighten if necessary

Includes two 6 foot fill hoses, 2 Washers, 2 Screens. For a single hose order WP76314

This accessory assembly is the factory-specified kit used to attach or secure designated parts on your appliance. Replacing missing or worn pieces restores a solid, factory fit and finish.

• Provides the original mounting/attachment components specified for your model
• Replaces lost or damaged hardware after installation, moving, or service
• Helps correct loose, misaligned, or rattling parts caused by missing fasteners
• Maintains proper alignment and appearance of exterior parts such as trim or handles

• Disconnect power; also shut off water and/or gas supplies before servicing
• Protect finished surfaces; start fasteners by hand to avoid cross-threading or damage
• Follow your model's service or installation guide for correct order and placement
• After assembly, verify everything is secure and test operation before returning to service

Razor blade scraper.

This pusher fits into the feed tube to guide ingredients safely and engage the cover interlock. Replace a cracked or missing pusher to restore safe operation and smooth, controlled feeding during slicing or shredding.

• Guides food down the chute while keeping hands away from sharp blades/discs
• Completes the lid/bowl interlock so the motor runs only when properly assembled
• Helps maintain even, consistent feeding for better cutting results
• Common symptoms: unit won't start unless pressure is applied to the pusher, uneven feeding, or visible cracks/missing pusher

• Unplug the appliance before servicing
• Remove the lid and old pusher; clean the feed tube area
• Align and insert the new pusher without forcing; ensure it seats fully to engage the interlock
• Handle cutting blades and discs carefully—they are sharp

Right side tool part # AP3778556

The 6 Wire Whip quickly incorporates air into ingredients for fluffy whipped cream, perfect boiled frostings and cakes with whipped egg whites and is used on 5 Quart Bowl-Lift KitchenAid Stand Commercial Mixer models KSMC50 and KM25G0X.

This is the turbo beater used on compatible hand mixers. Replace a bent, missing, or worn beater to restore smooth, balanced mixing performance and consistent results without wobble, chatter, or ingredients left unmixed.

• Attaches to the mixer drive to beat and blend ingredients uniformly
• Corrects wobbling, scraping, or poor mixing caused by a bent or damaged beater
• Addresses issues where the beater won't lock in, falls out, or spins unevenly
• Helps reduce vibration and noise when the original beater is out of true

• Unplug the mixer before servicing
• Identify left/right orientation per your model; some mixers use different beaters on each side
• Align the beater shaft with the correct socket and push in until it clicks; tug gently to confirm it's locked
• Test on the lowest speed first; stop and reseat if any wobble occurs

Kit contains 2 brackets and 4 screws. Used for granite and corning

This drain hose adapter connects the appliance's drain hose to another hose or a compatible fitting, providing a secure, leak-resistant joint so wastewater can be routed to the household drain. Replace when the original adapter is cracked or loose.

• Couples the drain hose to another hose or to a sink/disposal/standpipe fitting
• Helps seal the joint to reduce leaks and hose slippage
• Restores a tight fit when the original adapter is worn, brittle, or missing
• Symptoms of a bad adapter: leaking at the connection, hose won't stay attached, visible cracks

• Disconnect power and turn off water before servicing
• Place a towel or pan to catch residual water from the hose
• Fully seat hose ends over the adapter barbs and secure with appropriate hose clamps
• Run a short test cycle and inspect all connections for leaks

The Cooktop Bracket Kit is an OEM part for Bosch cooktops. This bracket and hardware kit serves to securely fasten the cooktop surface to the underlying countertop.

Causes of a bad bracket can include wear and deformation from heavy cooktop use over time, or damage to fastening screws from accidental impacts.

Symptoms of a bad bracket and fastening kit include:

• The cooktop surface becoming loose, wobbly, or unstable during use
• Gaps appearing between the cooktop and countertop edges
• Reduced heat containment and risk of burns from loose surfaces

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This door reversal kit provides the hardware needed to change the door swing to the opposite side on compatible appliances. Reverse the hinge and strike positions to improve access in tight spaces or match your layout.

• Reverses door swing by relocating the hinge and door strike to the opposite side
• Helps prevent interference with nearby walls, cabinets, or adjacent appliances
• Useful when rearranging a laundry pair or installing in a narrow alcove
• Not intended to repair damaged hinges, latches, or warped doors

• Disconnect power and, if applicable, gas supply before servicing
• Support the door during removal; a second person is recommended
• Move hinge/strike and reinstall fasteners per instructions; avoid overtightening into metal or plastic
• After conversion, verify latch engagement and door seal before use

Stainless Steel Commercial 11 Wire Elliptical WHIP for 7 and 8 Quart Bowl-Lift Stand Mixers. The Elliptical Wire Whip quickly incorporates air into ingredients for fluffy whipped cream, perfect for whipped egg whites added to frostings and cakes. Fits KitchenAid Stand Mixer models KL26M8, KP26M8, KP26M9, KP26N9, KSM7581, KSM7586, KSM7588, KSM7589, KSM7990, KSM8990, KSMC895, 3KSMC895, 4KSM7990, 5KSM7580, 5KSM7581, 5KSM7586, 5KSM7590, 5KSM7591, 5KSM7990, 5KSMC895, 7KSM7586, 9KSM7990, 9KSMC895.

This stainless-steel braided dishwasher connector links your home's water supply to the dishwasher inlet. The 72-inch length and 3/8 in Comp x 3/8 in MIP fittings provide a durable, properly sized connection for installations using these ends.

• Connects the shutoff/angle stop to the dishwasher inlet
• 72-inch length accommodates routing through cabinets and tight spaces
• Braided stainless-steel jacket for durable service
• Replace if you notice leaks at the hose or fittings, visible corrosion/fraying/kinks, or slow/no fill from restriction

• Disconnect power and shut off water at the supply valve before starting
• Place a towel or pan to catch residual water
• Start all threads by hand to avoid cross-threading; tighten with a wrench until snug—do not overtighten
• Use thread sealant only on tapered pipe threads if required; do not use on compression seats. Open the valve slowly and check for leaks.

This griddle creates a flat, continuous cooking surface that rests on your range or cooktop grates. It adds versatile space for items like pancakes and sandwiches, and replaces a worn or missing original griddle to restore safe use. What it does:

• Provides a broad, flat surface across burners for griddle-style cooking
• Direct replacement for a damaged, warped, or missing griddle
• Useful for foods that need a continuous surface (pancakes, eggs, grilled sandwiches)
• Common reasons to replace: wobbling/poor fit on grates, cracks, or persistent sticking from wear

• 1 griddle

• Turn all burners off and let the cooktop cool before placing or removing the griddle
• Position per your model's instructions so it sits flat and secure on the grates
• Preheat gradually on low to medium heat; handle only with oven mitts
• Allow the griddle to cool completely before cleaning or moving