Heating Element

Oven won't heat or bakes unevenly? This lower bake element restores proper heating for baking and roasting. Easy DIY repair—unplug, swap out, done.

The Surface Element is an OEM part for Bosch cooktop and ranges. Measuring 6 inches across, it provides focused heat from below for smaller sized cookware.

Causes of a bad 6" plug-in element generally relate to normal wear and tear over time. Spills left on the coils could potentially cause issues by corroding internal wiring or damaging heating components.

Symptoms of a bad narrow surface element can include:

• The element heating intermittently or not at all
• Only parts of the coil visibly heating up
• Buzzing or clicking coming from below the element
• Tripped circuit breakers affecting that specific element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

If your oven won't broil or top heat is weak, this broil element restores upper heating. Fits into cavity and connects to existing terminals.

Burner not heating or heating unevenly? This 6-inch surface coil element restores consistent heat to your electric range. Simple plug-in replacement.

This bake element replaces the oven's lower heating element to restore normal baking heat and even cooking results. It fits compatible electric ovens and is a direct-replacement designed for safe, reliable operation. What it does:

• Heats during bake cycles to provide consistent oven temperature for cooking and baking
• Common fix when the oven won't heat or bake function fails
• Replaces elements that are visibly damaged, blistered, or show open continuity
• Helps eliminate cold spots and uneven baking when the element is functioning correctly

• One bake element

• Disconnect power to the appliance at the breaker before starting work
• Wear gloves and allow the oven to fully cool; access is typically from inside the oven or rear panel depending on model
• Remove and replace carefully, reconnecting terminals securely and checking for proper operation before restoring regular use
• If you see damage to mounting hardware or insulation, replace those parts as needed per service instructions

A top heating element that restores heat to an electric cooktop so pots and pans heat properly. Fits the range cooktop surface and replaces a damaged or non-heating radiant element for reliable cooking. What it does:

• Provides the cooking heat on the cooktop surface; transfers power into radiant heat for cookware
• Commonly replaces elements that no longer heat, heat unevenly, or fail to glow/hot
• Works with the cooktop's surface/controls to regulate cooking temperature
• Helps eliminate cold spots or intermittent heating caused by a defective element

• Disconnect power at the breaker before servicing the range to avoid shock.
• Handle the element and surrounding ceramic/glass surface carefully to prevent cracking or damage.
• Installation may require accessing the cooktop terminals from under the surface; keep track of terminal connections.

If your cooktop burner won't heat or stays on high, this surface heating element may need replacement. Moderate DIY repair with basic tools.

This bake element heats the oven's lower chamber so food and bake cycles reach cooking temperatures. Replace a damaged or non-heating element to restore even baking and proper oven operation. What it does

• Converts electrical power into heat for the oven's bake cycle.
• Heats the oven's lower cavity to maintain set cooking temperatures.
• Commonly replaced for symptoms like no heat, weak heat, or uneven baking.
• Works with the oven's controls and sensors to deliver consistent bake performance.

• Disconnect power to the range at the breaker before starting any work.
• Allow the oven to cool completely and wear gloves to protect against sharp edges.
• Remove the oven racks and detach mounting screws and wire connectors to replace the element.
• Only reconnect power after the element is secured and wiring is reattached; test on a short bake cycle.

Broiler not heating or browning food? This broil element provides direct heat for finishing and browning. Moderate DIY repair for most home ranges.

Oven not heating or baking unevenly? This lower bake element restores consistent heat for even cooking. DIY-friendly repair in under 30 minutes.

Oven not heating or baking unevenly? This lower bake element restores consistent bottom heat for proper baking temperatures and even cooking results.

Oven not heating or baking unevenly? This lower bake heating element restores proper oven temperature for consistent cooking. Moderate DIY repair.

Oven not heating on bake? This bake element heats the bottom of your oven cavity for even cooking. Fixes broken or visibly damaged heating elements.

Broiler won't heat or food isn't browning? This broil element provides direct high heat for broiling and browning. Straightforward replacement.

• Genuine OEM Part: Produced by Whirlpool for unmatched compatibility and reliability with Maytag and Magic Chef appliances.
• Spade Style Connections: Features secure spade terminals for easy electrical connections.
• Exact Fit: Sized at 16x16 inches with 2-inch deep terminals for a perfect fit in specific models.

Common Symptoms for Maytag Magic Chef Oven Bake Element WP7406P012-60:

• Oven not heating evenly or not heating at all
• Visible damage or breakage in the element
• Oven taking longer than usual to preheat
• Inconsistent baking results

Basic Troubleshooting for Maytag Magic Chef Oven Bake Element WP7406P012-60:

• Check for Visual Damage: Inspect the bake element for any signs of wear or damage. Look for blisters, breaks, or areas that might be discolored (typically a burnt orange or darker spots).
• Test for Continuity: Using a multimeter, test the element for continuity. A lack of continuity indicates that the element is faulty and needs replacement.

Installation Instructions for Maytag Magic Chef Oven Bake Element WP7406P012-60:

1. Ensure Safety: Disconnect power to the oven by unplugging it or turning off the circuit breaker.
2. Access and Remove the Old Element: Remove the oven racks for better access, unscrew the mounts, and gently pull the element forward to reach the terminals.
3. Disconnect and Replace: Detach the spade connectors from the old element and connect them to the new one. Secure the new element in place with the original screws.
4. Operational Test: After installation, reconnect power and briefly turn on the oven to ensure the new element functions correctly.