Parts for Lg CW2079CWN: Cabinet / Control Panel Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

This holder is a small mounting bracket that secures internal components and keeps assemblies aligned for reliable operation. It replaces a worn or broken bracket to stop rattling and prevent parts from shifting. What it does

• Secures and positions nearby components or assemblies to maintain correct alignment
• Prevents vibration, rattling, or intermittent contact caused by a loose or cracked bracket
• Restores proper spacing so sensors, panels, or moving parts operate smoothly
• Helps prevent further wear or damage from misaligned parts

• One holder as shown

• Turn off power and disconnect the appliance before attempting any repairs
• Installation typically requires basic hand tools; save removed screws and clips for reassembly

Size: 4 3/4 inches. Used to secure the washer tub before transporting. They must be removed before using your washer.

Size: 6 1/4 inches. Used to secure the washer tub before transporting. They must be removed before using your washer.

Secures the washer’s tub and basket during moving to prevent internal damage. If the originals are missing after a move, install replacements for transport and remove them before using the washer.

What it does

• Locks the tub and basket to limit movement in transit
• Helps prevent suspension damage and internal rattles while relocating
• Replaces missing, bent, or stripped transport bolts
• Useful for moves, storage, or service shipments

What’s included
One shipping bolt assembly (sold individually).

Install notes

• Unplug power and turn off water before service
• Insert through the rear panel into the designated mounting point; tighten snugly—don’t overtighten
• Do not operate the washer with shipping bolts installed; remove all bolts after placement
• Some models use multiple bolts and lengths—match count/positions to your owner’s manual

Usage tip
After removal, bag and tape the bolts to the cabinet so they’re on hand for the next move.

This lifter assembly is the drum baffle inside the washer's inner tub. It lifts and tumbles laundry as the basket turns—replacing a cracked or missing lifter restores proper turnover, helps prevent fabric damage, and quiets thumping noises.

• Provides the lift/turn action that moves clothes through water and detergent
• Helps distribute loads to reduce tangling and improve cleaning results
• A loose, broken, or missing baffle can cause rattling or scraping noises
• Damage can lead to poor turnover or fabric snagging

• Disconnect power before servicing; wear gloves—the inner drum edges can be sharp
• Access from the drum opening; remove the old lifter by releasing tabs or removing screws (varies by model)
• Align the new lifter with the inner-tub slots, lock tabs in place, and secure as designed
• Verify all baffles are firmly attached before running a test cycle

The Spider is an OEM replacement part for LG washing machines. The spider is a central part located inside the washer tub that the inner tub spins on during the washing cycle. It plays an important role in evenly distributing load vibration across the washer tub and chassis.

Causes of a bad spider can include cracks or wear to the plastic housing over time due to continuous use and load stress, or damage from heavy impacts during transport or installation.

Symptoms of a bad spider include:

• Excessive vibration and noise during spin cycles
• The inner tub wobbling or becoming imbalanced
• Cracks or breaks in the spider housing
• Premature wear of other internal components like bearings

This genuine LG OEM replacement part is also compatible with some Kenmore models.

The Tub Bearing is an OEM replacement part for LG front-loading washing machines. This is the inner tube bearing that allows the tub to spin freely during the wash cycle.

Causes of a faulty tub bearing can include wear from repeated cycles, excessive vibrations putting strain on components, or foreign material intrusion into the bearing area.  

Symptoms include: 

• Noisy or grinding sounds emanating from inside the tub during operation
• Reduced spin efficiency causing wet clothes  
• Vibrations transferred to surrounding cabinetry

This LG replacement bearing restores smooth, quiet operation. Compatible with some Kenmore models as well, replacing it prevents potential tub damage from friction. 

The Tub Bearing is an OEM replacement part for LG washing machines. It is a crucial component that supports the weight of the tub and allows for smooth rotation during the wash and spin cycles.

Causes of a bad tub bearing can include excessive wear over time due to high-speed spinning, damage from overloading or unbalanced loads, or lack of proper lubrication.

Symptoms of a bad tub bearing include:

• Loud grinding or growling noises during the wash or spin cycle
• Excessive vibrations or shaking of the washing machine
• Leaks due to increased stress on the tub and other components
• Difficulty in starting or maintaining the spin cycle

This OEM LG part is also compatible with Sears/Kenmore models.

The Motor Rotor Bolt is an OEM part for LG washing machines. It secures the rotor to the motor shaft, playing a crucial role in the efficient functioning of the motor and ensuring the washer drum spins correctly during wash cycles.

Causes of a bad motor rotor bolt can include wear and tear from prolonged use, corrosion due to exposure to moisture, or damage from over-tightening or accidental impacts. A faulty motor rotor bolt can compromise the stability of the motor, leading to various operational issues.

Symptoms of a bad motor rotor bolt include:

• The washer drum not spinning or spinning irregularly
• Unusual noises during operation, such as banging or clunking
• The washer failing to complete cycles or stopping mid-cycle
• Visible wear or damage to the bolt or surrounding components

This OEM LG part is also compatible with Sears/Kenmore models.

The Tub Seal Gasket is an OEM part for LG washing machines. It creates a tight seal between the inner and outer tubs during the wash cycle, preventing leaks and containing water. The gasket helps prevent water from escaping the tub. 

Causes of a bad gasket can include wear and tear from repeated use over time, exposure to cleaning chemicals or extreme temperatures, or damage from handling heavy loads. 

Symptoms of a bad gasket include: 

• Water leaking from the outer tub during operation
• Excessive moisture in areas surrounding the washer 
• The tub making creaking or grinding noises
• Decreased washing or spinning performance

This OEM LG part can also be used on Kenmore/Sears appliances. 

This balance weight stabilizes the washer tub during spin cycles to reduce vibration and excessive movement, helping restore quieter operation and prevent further stress on suspension components and fasteners. What it does

• Counters the rotating tub to reduce vibration and rocking during spin cycles.
• Helps stop excessive movement, banging noises, and uneven spinning that can indicate an unbalanced load or worn mounting hardware.
• Replaces a damaged or missing counterweight to regain stable, consistent spin performance.
• Mounts to the washer cabinet/tub area and secures with factory fasteners.

• Disconnect power and water supply and run a drain/spin or remove standing water before beginning work.
• Removing the washer cabinet or front panel is often required; support the tub and components while you work.
• Use appropriate hand tools and keep OEM fasteners for reinstallation; follow the appliance service manual for exact steps.
• Wear gloves and eye protection.

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

The Outer Door Gasket Clamp is an OEM part for LG washing machines. It is designed to secure the outer door gasket, ensuring a tight seal between the door and the drum. This helps prevent water leaks during the wash cycle and maintains the efficiency of the washing machine.

Causes of a bad outer door gasket clamp can include regular wear and tear, damage from heavy use, or corrosion over time. A compromised clamp can lead to a loose gasket, resulting in water leaks and reduced washing machine performance.

Symptoms of a bad Outer Door Gasket Clamp include:

• Water leaking from the door area during wash cycles
• A loose or misaligned door gasket
• Difficulty in securing the door properly
• Visible rust or damage on the clamp

This OEM LG part is also compatible with Sears/Kenmore.

This washer balance weight mounts to the outer tub to absorb vibration and stabilize the drum during spin. Replacing a damaged or missing weight helps restore smoother, quieter operation and reduces movement caused by unbalanced loads. What it does:

• Adds mass to the outer tub to counterbalance spinning loads
• Helps reduce vibration, banging, and "walking" during spin
• Supports proper spin speed and cycle completion
• Replaces a cracked, crumbling, or loose tub weight

• 1 balance weight

• Disconnect power and water supply before servicing
• Access the weight by removing the necessary panels
• Support the tub and hold the weight while removing/installing bolts; tighten evenly in a crisscross pattern
• Reuse existing mounting hardware and ensure all weights and mounting points are intact before testing

This multi-wire harness connects the washer's control system to multiple components. Replacing a damaged harness restores reliable power and signal routing and can help resolve intermittent operation, error codes, or no-spin/no-drain conditions caused by broken or burnt wires.

• Distributes electrical power and control signals between the PCB and components such as the motor, drain pump, inlet valves, sensors, and door lock
• Provides factory-terminated, keyed connectors and correct routing paths for secure, plug-in connections
• Typical failure symptoms: won't start or intermittent operation, component-related error codes, no spin/drain/fill, or visible heat damage to wires/connectors
• Using the exact harness maintains proper connector types and lengths for your appliance's design

• Disconnect power and turn off water supply before servicing
• Access the harness by removing panels as needed; take photos to document original routing and connections
• Transfer plugs one at a time; match keyed connectors and do not force them into place
• Secure the new harness under factory clips and away from sharp edges or moving parts; test operation before reassembly

The LG Door Hinge Assembly is an essential component of LG washers. This OEM replacement part is specifically designed to ensure the smooth and secure operation of the washer's door. The hinge assembly is responsible for connecting the door to the main body of the appliance, allowing easy access to the washing drum. It provides stability and durability to the door, enabling it to open and close effectively during the washing and loading processes.

This part fixes the following symptoms:

• Difficulty in opening or closing the washer door
• Door sagging or misalignment
• Excessive noise or squeaking when operating the door
• The door not staying securely closed during washing cycles
• Visible damage or wear on the hinge assembly

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

The Washer Gasket is an OEM replacement part for LG washing machines. It is a flexible seal that lines the opening of the washer tub, creating an airtight barrier to prevent water leaks and ensure proper containment during the wash and spin cycles.

Symptoms of a bad washer gasket include:

• Water leaking from the front of the washing machine
• Excessive moisture or condensation buildup around the gasket area
• Difficulty in properly closing and latching the washer door due to a worn or damaged gasket

Causes of a washer gasket failure can range from general wear and tear over time, to physical damage from being pinched or cracked, to improper installation or alignment issues.

This OEM LG part is also compatible with Sears/Kenmore models.

The Motor Stator Bolt is an OEM part for LG washing machines. This bolt secures the stator to the motor, ensuring the stability and proper functioning of the washing machine's motor assembly.

Causes of a bad motor stator bolt can include wear and tear over time, improper installation, or damage from over-tightening or impact. A compromised bolt can lead to instability in the motor, potentially affecting the washer's performance.

Symptoms of a bad motor stator bolt include:

• Unusual noises during the wash cycle
• Vibrations or shaking of the washer
• The motor not functioning properly or failing to start

This OEM LG part is also compatible with Sears/Kenmore.

This is a replacement single electrical harness that restores the factory wiring connection between components. It provides a like-for-like connection to help return affected functions to normal operation when wiring is damaged. What it does:

• Carries electrical signals/power between components and the appliance control circuits
• Replaces frayed, melted, or broken wiring that can cause intermittent or complete function failure
• Commonly used when a component has no power, a circuit is open, or functions stop responding
• Helps eliminate loose connector issues that cause intermittent operation or error codes

• One (1) single electrical harness (part 6877ER3003C)

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Match connector shapes and pin counts; do not force connectors—verify secure seating
• Route and secure the harness per factory paths and clips to prevent chafing or heat exposure
• If you see melted connectors, burned insulation, or repeated failures,

This replacement refrigerator door handle restores a secure grip and normal door operation after a cracked, broken, or loose handle. Designed to match the original fit and finish for a clean, factory look. What it does

• Provides a functional grip so doors open and close reliably
• Replaces cracked, bent, or detached handles that prevent safe operation
• Restores proper alignment and reduces door movement or wobble
• Helps maintain an airtight seal by allowing the door to fully close

• Use basic hand tools; avoid power tools that can strip fasteners
• Keep door supported while removing/installing the handle to prevent damage
• Do not overtighten screws—secure snugly to avoid cracking the handle

The Door Latch Hook is an OEM replacement part for LG front load washers. It is a component of the overall latch and locking assembly and works to securely close and lock the washer door. With a properly functioning latch hook, the washer door remains tightly sealed during cycles to ensure optimal water retention and the most thorough cleaning. 

Symptoms of a bad door latch hook include:

• Water leaks around the door during washing cycles
• The door fails to latch fully and unlock after cycles 
• Difficulty opening or closing the washer door completely
• Alignment issues like misaligned or skewed door positions

Causes of a bad door latch hook can include wear over extended use. Damage may also result from washing hard or abrasive items that put excess strain on the latch mechanism over time.

This OEM LG part is compatible with Sears/Kenmore front-load washer models as well. 

The Water Inlet Valve Assembly is an OEM replacement part for LG washing machines, designed to control the flow of water into the laundry tub. This part is responsible for opening and closing to allow water into the wash drum at the appropriate times during the wash cycle, providing the correct water level and temperature.

Causes of a bad Water Inlet Valve Assembly can include mineral deposits blocking the valve, electrical failure preventing the valve from opening or closing properly, or physical damage to the valve mechanism itself.

Symptoms of a bad Water Inlet Valve Assembly include:

• Inadequate filling of the washer drum
• Water entering the drum when the washer is off
• Unusual noises during the fill cycle
• Water that is too hot or too cold, indicating a failure in valve operation that controls temperature

This OEM LG part can also be used on Kenmore/Sears appliances. 

This base bracket mounts to the washer's lower frame to hold associated components securely in place. By keeping parts properly anchored, it helps maintain alignment and stability during operation to minimize vibration and noise.

• Attaches to the washer base and provides a mounting point for designated hardware
• Helps keep assemblies from shifting during agitation and spin
• Supports smooth, quieter operation by reducing vibration and rattling
• Common signs of failure include a bent or cracked bracket, loose/misaligned parts, or unusual noises from the base area

• Disconnect power and water supply before servicing; move the appliance for safe access
• Carefully tip or lay the washer back on protective padding; use a helper for stability
• Note the bracket's orientation and reuse existing mounting hardware as applicable
• Tighten fasteners securely and verify nearby parts have proper clearance before test run

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This inlet hose supplies fresh water from the household line to the dishwasher. Replace a damaged or leaking hose to help restore proper filling and prevent water leaks during operation.

• Channels water from the supply valve to the dishwasher's inlet
• Common failure signs: leaks under or behind the unit, fill errors, slow or no fill
• Helps resolve intermittent water supply issues caused by a kinked or cracked hose

• Unplug power and shut off the water supply before starting
• Place a towel or pan to catch residual water when disconnecting
• Check for leaks after installation and tighten connections as needed

This inlet hose is the internal water line for your dishwasher, routing fresh water from the fill valve into the wash system. Replacing a brittle or leaking hose restores reliable filling and helps protect floors and cabinetry from water damage.

• Channels incoming water from the inlet valve to the tub/sump
• Maintains proper fill level and flow at the start of each cycle
• A cracked, kinked, or loose hose can cause leaks or slow/no fill
• Restores correct water delivery and helps prevent water damage

• Disconnect power and shut off the water supply before servicing
• Pull the dishwasher forward for access; place a towel or pan to catch residual water
• Note the original routing and clamp positions; transfer clamps and avoid kinks
• Restore water, run a quick fill cycle, and check all connections for leaks

This part may be black or gray in color.

The Thermistor Assembly is an OEM component specifically designed for front loading LG washing machines. It plays an important role in monitoring and regulating temperatures during heated wash cycles. The thermistor detects temperature changes within the wash drum and sends this information to the control board to ensure clothes are washed at the optimal temperature.

Causes of a bad thermistor assembly can include general wear and tear over time, exposure to extreme temperatures, or damage due to impact or mishandling during cycles.

Symptoms of a bad thermistor assembly include:

• Inability to reach or maintain set temperatures
• Fluctuating water temperatures
• Error codes related to temperature sensing

This OEM LG part is also compatible with Sears/Kenmore washers.

The Dispenser Hose is an OEM part for LG washing machines. It connects the detergent dispenser to the washer tub, allowing detergent and other cleaning agents to be delivered effectively during the wash cycle.

Causes of a bad dispenser hose can include regular wear and tear, damage from harsh detergents, or physical damage due to kinks, pinches, or impact. Over time, the hose can become brittle, cracked, or clogged, affecting its ability to function properly.

Symptoms of a bad dispenser hose include:

• Leaks or drips from the hose area
• Detergent not dispensing correctly or at all
• Water pooling around the washer
• Visible cracks or splits in the hose

This OEM LG part is also compatible with Sears/Kenmore models.

This thermistor seal is the grommet that seals the temperature sensor where it passes through the washing machine's outer tub. Replacing a worn seal restores a watertight fit and helps prevent leaks that can damage surrounding components. What it does

• Forms a watertight barrier around the tub temperature sensor (thermistor)
• Helps keep the sensor securely positioned in the mounting port
• Common failure symptoms: water leaking during cycles, puddles under the unit, visible cracking/hardening of the grommet, or a loose sensor fit

• 1 thermistor seal

• Disconnect power and water; drain any remaining water from the tub
• Access the thermistor on the outer tub, disconnect its harness, and remove the sensor
• Pull out the old seal, clean the opening, press in the new seal, and reinstall the sensor fully seated
• Run a brief test cycle and check for leaks before final reassembly

The Vent Hose is an OEM part for LG washing machines. This hose is essential for ensuring proper ventilation within the washer, allowing air to circulate and preventing the buildup of moisture and mildew. It helps maintain the efficiency of the washing machine by facilitating the expulsion of air and excess water vapor during operation.

Causes of a bad washer vent hose can include wear and tear over time, blockages from lint or debris, or damage due to bending or pinching.

Symptoms of a bad vent hose include:

• Excessive moisture or condensation inside the washer
• Musty odors from the washing machine
• Visible cracks or holes in the hose
• Poor ventilation leading to inefficient washing cycles

This OEM LG part is also compatible with Sears/Kenmore.

This inlet hose connects the home water supply to the appliance so it can fill properly. It replaces a worn or leaking supply hose to restore safe, reliable water flow for normal cycles. What it does:

• Directs incoming water from the household supply to the appliance inlet valve
• Works with the appliance's inlet valve and fittings to allow proper fill and rinse actions
• Commonly replaces hoses that leak, spray, kink, or block water flow
• Helps stop slow fills or intermittent filling caused by damaged or deteriorated hoses

• One inlet hose

• Turn off water supply and disconnect power before starting work
• Inspect and replace any damaged O-rings or fittings; use approved replacement fittings if needed
• Hand-tighten connections, then snug with a wrench—avoid over-tightening to prevent damage
• After installation, restore water and power, run a short fill cycle, and check all connections for leaks

The Dispenser Inlet Hose is an OEM part for LG washing machines. This hose directs water from the water inlet valve to the detergent dispenser, ensuring that water mixes with the detergent before entering the drum for efficient washing. The hose is designed to withstand high water pressure and temperature fluctuations.

Over time, the dispenser inlet hose can become clogged, cracked, or worn out due to regular use. Causes of a bad inlet hose include mineral deposits or debris buildup, wear and tear, and exposure to high temperatures or pressure that can cause the hose to degrade.

Symptoms of a bad dispenser inlet hose include:

• Leaking water around the detergent dispenser area
• Reduced water flow into the dispenser
• Visible cracks or wear on the hose
• Incomplete dissolution of detergent during wash cycles

This OEM LG part is also compatible with Sears/Kenmore.

The Dispenser Inlet Hose is an OEM part for LG washing machines. This hose directs water from the water inlet valve to the detergent dispenser, ensuring that water mixes with the detergent before entering the drum for efficient washing. The hose is designed to withstand high water pressure and temperature fluctuations.

Over time, the dispenser inlet hose can become clogged, cracked, or worn out due to regular use. Causes of a bad inlet hose include mineral deposits or debris buildup, wear and tear, and exposure to high temperatures or pressure that can cause the hose to degrade.

Symptoms of a bad dispenser inlet hose include:

• Leaking water around the detergent dispenser area
• Reduced water flow into the dispenser
• Visible cracks or wear on the hose
• Incomplete dissolution of detergent during wash cycles

This OEM LG part is also compatible with Sears/Kenmore.

The Drain Pump and Motor is an original LG (OEM) replacement part for LG made washing machines that is responsible for removing water from the washer at the end of the wash cycle. The pump forces water out through the drain hose so that clothing comes out free of excess water, making the drying process faster. 

Symptoms of a failing Drain Pump Motor include:

• Water not draining out of the washing machine 
• Noisy or unusual sounds coming from the pump area during the drain cycle
• The washing machine stopping mid-cycle

Causes of a bad Drain Pump Motor can range from obstructions in the pump or hose, which can strain or damage the motor, to wear and tear from regular use leading to motor failure. Electrical issues can also affect the motor's performance, preventing it from operating correctly.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Drain Hose is an OEM part for LG washing machines. It is designed to carry used water from the washing machine to the household drain. This hose ensures that water is efficiently expelled from the washer, preventing any overflow or leakage issues.

Causes of a bad drain hose can include cracks or splits due to wear and tear, clogs from debris or residue buildup, and damage from mishandling or improper installation. Such issues can compromise the hose's ability to transport water effectively.

Symptoms of a bad Drain Hose include:

• Water leaks during or after the wash cycle
• The washer not draining properly
• Visible cracks or damage to the hose
• Unpleasant odors due to trapped debris or standing water

This OEM LG part is also compatible with Sears/Kenmore models.

The Pump Casing is an OEM replacement part for LG washing machines. It is a crucial component that houses the drain pump, which is responsible for removing water from the wash tub during the drain and spin cycles.

Symptoms of a need to replace the pump casing:

• Leaks or water seeping from the pump area
• Unusual noises or vibrations during the drain or spin cycles
• Pump failure or inability to drain water effectively
• Cracks or damage to the casing itself

Causes of a faulty pump casing can include physical impact or mishandling, excessive wear and tear over time, or potential manufacturing defects.

This OEM LG part is also compatible with Sears/Kenmore washing machines.

The Pump Filter Assembly is an OEM replacement part for LG washing machines. It is a crucial component that filters out lint, debris, and other particles from the wash water, preventing them from recirculating and damaging the pump or other internal components.

Symptoms of a need to replace the pump filter assembly:

• Clogging or blockages, leading to poor drainage or water not draining completely
• Excessive buildup of lint, hair, or other debris in the filter screen
• Leaks or water seeping from the filter housing or surrounding area
•  Unusual noises or vibrations during the drain or spin cycles, indicating a potential blockage

Causes of a faulty pump filter assembly can include excessive lint accumulation, damage to the filter screen or housing due to impact or mishandling, and general wear and tear over time.

This OEM LG part is also compatible with Sears/Kenmore washing machines.

The stator assembly is the stationary coil pack for the direct-drive motor in your washer. Working with the rotor, it creates the magnetic field that turns the tub and restores consistent wash and spin performance. What it does:

• Generates the electromagnetic field that drives the rotor and spins the drum
• Failure can cause no spin or agitation/tumble, or a stalled drum
• May trigger LE/motor error codes and a humming or grinding noise from the motor area
• Can produce a burning smell or signs of overheating near the rear of the machine

• 1 stator assembly

• Disconnect power; move the appliance for rear access and turn off water if needed
• Remove the rear panel, rotor bolt, and rotor; handle strong magnets with care
• Unbolt and replace the stator; transfer the hall/position sensor and harness if attached, and secure wiring
• Reinstall the rotor and panel; run a test spin

The Sensor Assembly is an OEM part for LG washing machines. This component is crucial for detecting and monitoring various conditions within the washing machine, such as water level, temperature, and load balance. It ensures the machine operates efficiently and effectively by providing accurate data to the control board.

Causes of a bad sensor assembly can include wear and tear from regular use, exposure to water and detergents, electrical malfunctions, or damage from impact. A faulty sensor assembly can lead to incorrect readings, which can affect the washing machine’s performance and lead to issues such as improper water levels or unbalanced loads.

Symptoms of a bad Sensor Assembly include:

• Incorrect water levels during cycles
• The washing machine stopping mid-cycle or not completing cycles
• Error codes related to water level or load balance
• The machine failing to start or operate correctly

This OEM LG part is also compatible with Sears/Kenmore models.

The Rotor Assembly is an OEM part for LG washing machines. It plays a crucial role in the operation of the washer's motor, facilitating the rotation of the drum during the wash and spin cycles to ensure thorough cleaning and efficient water extraction.

You should replace this rotor assembly if it becomes damaged or worn out. Common causes of a bad rotor assembly include wear and tear from regular use, electrical malfunctions, or physical damage from foreign objects entering the washing machine.

Symptoms of a bad rotor assembly include:

• The drum not spinning or agitating
• Unusual noises during operation, such as grinding or clicking
• The washer not completing cycles properly
• Error codes related to motor or spin issues

This OEM LG part is also compatible with Sears/Kenmore models.

The Suspension Spring is an OEM part for LG washing machines. It helps support the washer tub, reducing vibrations and absorbing shocks during the washing and spinning cycles, ensuring smooth and quiet operation.

Causes of a bad suspension spring can include wear and tear from regular use, overloading the washer, or damage from unbalanced loads. Over time, the spring can lose its tension or break, compromising the washer's stability and performance.

Symptoms of a bad suspension spring include:

• Excessive shaking or vibrating during the wash or spin cycles
• Loud banging noises
• The washer moving or shifting during operation
• Uneven or incomplete washing or spinning

This OEM LG part is also compatible with Sears/Kenmore models.

The Water Level Pressure Switch is an OEM part for LG washing machines. It monitors the water level inside the washer and signals the control board to stop filling when the desired level is reached, ensuring the correct amount of water is used for each cycle.

Causes of a bad water level pressure switch can include electrical malfunctions, damage to the pressure sensor, or blockages in the air tube connected to the switch.

Symptoms of a bad water level pressure switch include:

• The washer overfilling or underfilling with water
• Inconsistent water levels during different cycles
• Error codes related to water levels
• The washer not progressing through cycles properly

This OEM LG part is also compatible with Sears/Kenmore models.

The Suspension Spring Holder is an OEM part for LG washing machines. This holder supports the suspension springs that help stabilize the washer drum during operation, reducing vibration and movement. It plays a critical role in ensuring smooth and quiet operation of the washing machine.

Over time, the suspension spring holder can become worn or damaged due to regular use, heavy loads, or accidental impacts. Causes of a bad suspension spring holder include wear and tear, physical damage, or corrosion from moisture exposure.

Symptoms of a bad suspension spring holder include:

• Excessive vibration or shaking during wash cycles
• Unusual noises, such as banging or clunking
• The washer drum appearing misaligned or sagging
• The washing machine moving or walking during operation

This OEM LG part is also compatible with Sears/Kenmore.

This Power Cord Assembly restores a secure, grounded connection from your wall outlet to the washer's internal power circuit. Replace a frayed or failed cord to resolve no-power issues and maintain safe operation. What it does:

• Delivers AC power from the wall outlet to the washer's internal power circuit (line filter/control)
• Provides a proper equipment ground path for the cabinet
• Replaces damaged or overheated cords that can cause power loss
• Common symptoms include: washer has no power, won't start, intermittent power when the cord is moved, or visible cord/plug damage

• 1 power cord assembly

• Disconnect the washer from power before servicing and verify the outlet/breaker are in good condition
• Access cord connections by removing the rear or top panel per your model's service information
• Note original routing and strain relief; reinstall clips/guides the same way to prevent chafing
• Secure the ground connection and fully seat all terminals; keep wiring clear of sharp edges before testing

The Drain Hose Assembly is an OEM part for LG washing machines. It is a component designed to transport used water from the washer to the drain. This flexible hose assembly ensures that water flows smoothly out of your washing machine after each cycle, preventing leaks and maintaining the efficiency of your appliance. 

Causes for replacement can include wear and tear over time, clogs from lint or small items, kinks that restrict water flow, or damage from moving or improper installation. 

Symptoms of a bad Drain Hose Assembly include:

• Water leaking from the back or bottom of the washing machine
• Difficulty draining water out of the washer
• Puddles of water forming around the appliance during or after operation

This OEM LG part is also compatible with some Kenmore models.

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn

The Washer Door Lock Switch is an OEM part for LG washing machines. This critical safety feature locks the washer door during operation to prevent it from being opened, which ensures safety and proper functioning. The door lock switch also communicates with the washer's control system to indicate that the door is securely closed and the machine can begin its cycle.

Symptoms of a bad Washer Door Lock Switch include:

• The washing machine refusing to start, despite the door appearing to be closed.
• The door failing to lock properly, or the lock releasing prematurely during a cycle.
• Error messages on the washer's display related to door closure issues.

Causes of a bad door lock switch can include mechanical failures such as worn or damaged locking mechanisms, electrical issues like faulty wiring or failed solenoids, or alignment problems that prevent the door from engaging the switch properly.

This OEM LG part is also compatible with Sears/Kenmore models.

This spring-style hose clamp secures a washer's rubber hose to its fitting to maintain a tight, leak-resistant seal. Replacing a weakened clamp helps stop drips and keeps the hose firmly in place during operation.

• Provides constant spring tension to hold a rubber hose on its port
• Helps prevent leaks at the connection point
• Resists vibration so the hose doesn't back off the fitting
• Common signs include water at a hose joint, a loose/detached hose, or a rusted/broken clamp

• Disconnect power and turn off water supply before servicing
• Place a towel or pan to catch residual water from hoses
• Use pliers to compress the ears, slide off the old clamp, position the new clamp behind the hose bead, and release evenly
• After reassembly, run a quick test cycle and check for leaks

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

This hose clamp secures a rubber hose connection to prevent leaks where the hose meets its fitting. A tight, uniform seal helps maintain proper water flow and keeps the appliance operating reliably.

• Provides a tight, 360-degree seal around the hose barb/fitting
• Helps correct issues like water leaks at the hose connection point
• Maintains correct hose attachment during operation and vibration
• Step-less ear design distributes clamping force evenly

• Unplug power and shut off water supply before servicing
• Note clamp orientation and hose routing before removal
• Use appropriate ear-clamp pincers or pliers to compress the clamp evenly
• Check the hose and fitting for wear; replace if cracked or deformed

This hose clamp secures a washer hose to its fitting to maintain a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop seepage at hose joints and keep the washer operating reliably.

• Holds the hose firmly on pump, tub, or drain fittings to help prevent leaks
• Maintains clamping pressure during operation and vibration
• Replace if rusted, bent, cracked, or no longer holding tension
• Typical symptoms: water dripping at hose connections or a hose that slips off

• Disconnect power and shut off water; drain any remaining water from the unit
• Release and slide back the old clamp, then remove the hose
• Fully seat the hose on the fitting and position the clamp just behind the hose bead/ridge
• Secure the clamp and run a brief test to check for leaks

This hose clamp secures a rubber hose connection to prevent leaks where the hose meets its fitting. A tight, uniform seal helps maintain proper water flow and keeps the appliance operating reliably.

• Provides a tight, 360-degree seal around the hose barb/fitting
• Helps correct issues like water leaks at the hose connection point
• Maintains correct hose attachment during operation and vibration
• Step-less ear design distributes clamping force evenly

• Unplug power and shut off water supply before servicing
• Note clamp orientation and hose routing before removal
• Use appropriate ear-clamp pincers or pliers to compress the clamp evenly
• Check the hose and fitting for wear; replace if cracked or deformed

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

The Noise Filter Assembly is an OEM part for LG washing machines, designed to minimize electrical noise interference within the appliance. This essential component ensures that the washer operates smoothly without emitting disruptive sounds that can affect both the performance of the washer and the comfort of your home environment. 

Causes of a bad Noise Filter Assembly can range from wear and tear over time to exposure to power surges or electrical spikes, which can damage the internal components of the filter. 

Symptoms of a bad Noise Filter Assembly include:

• Increased electrical noise or buzzing sounds emanating from the washer
• Intermittent disruptions in the washer's performance
• The washing machine failing to start or experiencing power fluctuations

This OEM LG part is also compatible with some Kenmore models.

The Gasket is an OEM part for LG washing machines, designed to ensure a watertight seal between the door and the washing machine's drum. This door gasket prevents water leaks during operation. Made from flexible, durable rubber, it conforms to the door and frame, creating a secure seal that keeps water contained within the washer during cycles. 

Causes for a Gasket to fail include normal wear and tear from frequent use, chemical degradation from laundry detergents and cleaners, and buildup of residue that can cause the material to deteriorate or lose its elasticity.

Symptoms of a bad Gasket include:

• Water leaking from the front of the washing machine
• Visible signs of wear, such as cracks, tears, or holes in the gasket.
• The presence of mold or mildew on the gasket
• Difficulty closing the washer door, or the door not sealing properly.

This OEM LG part can also be used on Kenmore/Sears appliances. 

NOTE: This gasket has a drain hole. For a gasket without a drain hole, order 4986ER0004B.

The Tub to Pump Hose is an OEM replacement part for LG top-load washing machines. This hose safely transports water between the wash tub and drain pump. The hose measures 13 inches in length.

Causes of failure relate to constant flexing under water pressure strains that accumulate over years of usage. Excess minerals in hard water areas promote accelerated breakdown of flexible PVC material.

Symptoms of a cracked or leaking tub to pump hose include: 

• Water not draining or taking an abnormally long time
• Water continually accumulating inside the machine cabinet   
• Error codes related to drainage issues displayed  
• Puddles forming near or under the back of the washer

This genuine LG hose is also compatible with select Sears/Kenmore units as well.

The Inner Door Gasket Clamp is an OEM part for LG washing machines. It secures the inner door gasket in place, ensuring a tight seal to prevent water leaks during the wash cycle. This clamp is essential for maintaining the efficiency and reliability of the washing machine by keeping the door gasket firmly in position.

Over time, wear and tear, exposure to water and detergent, or accidental mishandling can compromise the integrity of the clamp, leading to potential leaks.

Symptoms of a bad inner door gasket clamp include:

• Water leaking from the door area
• The door gasket not staying securely in place
•  Visible damage or corrosion on the clamp

This OEM LG part is also compatible with Sears/Kenmore.

The Air Chamber is an OEM part for LG washing machines. This part connects to the pressure switch and ensures the washer machine fills with the correct amount of water for the selected cycle. 

Causes of a bad  Air Chamber can include clogging due to detergent residue or debris, cracks or perforations that lead to air leaks, and aging of the material, which might compromise its integrity and function.

Symptoms of a faulty Air Chamber include:

• Inaccurate water level readings leading to overfilling or insufficient water during cycles
• Unusual noises during the fill cycle, indicating air escaping
• The washing machine failing to start the wash cycle due to improper water level detection
• Error codes displayed on the machine that relate to water level issues

This OEM LG part is also compatible with some Kenmore models.

The Hose is an OEM part for LG washing machines. This component is crucial for the proper flow of water into and out of the washing machine, ensuring efficient washing and rinsing cycles. The hose is designed to withstand high water pressure and regular use.

Causes of a bad hose can include wear and tear over time, exposure to harsh water conditions, or accidental damage such as kinks or punctures. Ensuring the hose is in good condition is essential to prevent leaks and maintain optimal water flow.

Symptoms of a bad hose include:

• Water leaks around the hose connections
• Reduced water flow into or out of the washing machine
• Visible cracks, bulges, or kinks in the hose

This OEM LG part is also compatible with Sears/Kenmore.

This hose connector joins two internal water lines inside your washer to create a secure, leak-resistant connection. Replacing a worn coupler helps stop drips and keeps water moving properly during fill, wash/recirculation, and drain cycles.

• Joins two hoses inside the appliance for a tight, reliable seal
• Helps maintain proper water flow during operation
• Replace if cracked, deformed, or if hoses slip off despite clamp tension

• Unplug the washer and turn off water supply; expect some residual water
• Access the hose junction and note hose routing and clamp positions
• Fully seat hoses onto the connector and secure clamps behind the hose bead
• Reassemble and run a short test cycle while checking for leaks

The Washing Machine Shock Absorber Kit is an OEM part for LG washing machines. This kit includes a shock absorber designed to reduce vibrations and absorb shocks during the wash cycle, providing stability and minimizing excessive movement. 

Over time, the shock absorbers can wear out due to regular use, exposure to heavy or unbalanced loads, or damage from impact. These factors can lead to reduced effectiveness of the shock absorbers, causing increased vibrations and noise.

Symptoms of a bad shock absorber kit include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging or thumping noises
• The washer moving or "walking" during operation
• Leaks due to increased stress on the tub and other components

This OEM LG part is also compatible with Sears/Kenmore.

The Hinge Pin is an OEM part for LG washing machines. It serves as a pivot point for the washer door, allowing it to open and close smoothly. This component is crucial for maintaining the proper alignment and function of the washer door, ensuring a secure and reliable seal during operation.

Common causes of a bad hinge pin include frequent use leading to wear and tear, physical damage from accidental impacts, or rust and corrosion over time. A compromised hinge pin can result in misalignment of the door, affecting the washing machine's ability to close properly and maintain an effective seal.

Symptoms of a bad hinge pin include:

• Difficulty opening or closing the washer door
• Door not staying securely closed during operation
• Squeaking or grinding noises when the door is moved
• Visible wear or damage to the hinge pin

This OEM LG part is also compatible with Sears/Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.