Cooktop Control Board

This OEM replacement part is an oven control board. The oven control board is the primary computer circuit board that controls the main functions of the oven. These functions include turning the oven on as well as adjusting and maintaining the temperature of the oven. Luckily, replacing a control board is a simple process.To replace the board, first, make sure the oven is unplugged. Gain access to the back of the oven and remove the upper back panel. Once the panel is removed, locate the old control board. Take note of the orientation of the wires by taking a photo with a phone camera. Disconnect the wire harness and any individual wires that are attached to the old board. Re-secure the wires into their correct positions. Snap the new board back in place and reinstall the upper back panel.This genuine replacement control board is compatible with Frigidaire Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This electronic control board manages your oven's display, keypad inputs, and heating functions. Replacing a failed board can restore responsive controls, proper bake/broil operation, and reliable timing so your range or wall oven works as designed. What it does:

• Interprets keypad inputs and updates the clock/temperature display
• Controls bake and broil circuits via onboard relays
• Monitors the oven temperature sensor to regulate heat
• Runs cooking modes and timers

• 1 electronic control board assembly

• Disconnect power at the breaker before servicing; verify no power is present
• Handle the board by the edges and use ESD precautions
• Note/photograph wire locations; transfer any brackets or supports from the original board
• After installation, restore power and test bake/broil functions to confirm operation

This is a Whirlpool range control board. It manages and monitors temperatures for the range and features a digital display and user interface buttons. The control board can short out due to power surge or exposure to excessive heat. For example, if the oven's self clean function is run too long or too frequently, parts of the control board could melt or otherwise malfunction.Before installing this part, be sure to cut power to the appliance and allow it to cool completely. The stove may need to be pulled away from the wall to access the screws holding the control panel in place. Remove the screws from each side of the control panel to gain access to the old control board. Disconnect any wire harnesses connected to it and remove any screws mounting it in place before installing the new part.This is a genuine OEM part compatible with ranges manufactured by Whirlpool brands, including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product is just the panel and contains no additional parts or hardware.

This electronic oven control board regulates and coordinates oven functions on gas ranges—driving the display, processing keypad inputs, and switching relays—so you can set temperatures and cycles reliably. Replacing a failing board restores responsive controls and consistent heating. What it does:

• Controls bake and broil ignition and temperature regulation in gas ovens
• Interprets keypad inputs and updates the display
• Switches power through onboard relays to igniters/valves as directed by sensors
• Common failure symptoms: blank or erratic display, unresponsive controls, oven won't start or heat, or recurring control error codes

• 1 electronic control board assembly

• Disconnect power at the breaker and shut off gas before servicing
• Use ESD precautions; handle the board by its edges
• Access the board behind the control panel; photograph wiring and move connectors one at a time
• Reuse existing mounting hardware; restore power and test oven functions after reassembly

• A faulty oven temperature sensor or keypad/touch interface can mimic control-board issues; test related components before replacement.

This electronic oven control board governs bake/broil functions and the display for Frigidaire-made ranges. Replace it to restore oven heat, accurate temperature regulation, and responsive controls when the original control fails. What it does

• Controls power to the bake and broil element/igniter and times oven cycles
• Monitors the oven sensor and maintains the set temperature
• Receives keypad inputs and drives the clock/temperature display
• Common symptoms: oven won't heat or overheats, display dead/dim, unresponsive buttons, intermittent shutoff, or error code on the display

• 1 electronic control board

• Disconnect power at the breaker before servicing; verify no voltage at the range
• Access the control through the backguard/control panel; photograph wiring for reference
• Handle the board by the edges to avoid static damage; move connectors one at a time
• Transfer the existing keypad overlay/trim and any mounting hardware from the old board

This replacement part is an oven control board and display. It houses the buttons that users push to control oven operation, including bake functions, temperature, and access to the timer and clock. Over time and through exposure to heat and moisture, the control board may corrode and fail. If the control board is damaged, the oven may not operate correctly or at all.To replace the oven control board, first unplug the oven from the wall. Next, remove the rear access panel from the stove. This should reveal the back of the control board. Remove the mounting screws and disconnect the wiring. Remove the old control board. When ready to install the new board, first remove the protective film, then place it on the slot. Install the mounting screws and reconnect the wiring. Replace the oven's rear access panel. Always wear gloves when repairing an oven.This is a genuine OEM replacement part. It's manufactured by Whirlpool and will fit Whirlpool, KitchenAid, and Kenmore ovens.

The Oven Control Board is an OEM part for Whirlpool ovens. It regulates and controls the various functions and settings of your oven, including the oven's temperature, timers, and cooking modes.   

A bad oven control board can occur due to electrical malfunctions, power surges, or component failure. If you notice symptoms such as an unresponsive control panel, error codes displayed on the screen, or erratic heating and temperature fluctuations, it may be time to replace the oven control board.

Symptoms of a bad oven control board include:

• Unresponsive control panel
• Error codes displayed on the screen
• Erratic heating and temperature fluctuations

Restore your oven by replacing the faulty or malfunctioning oven control board with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This electronic control board is the "brain" of the dishwasher, coordinating cycle timing and powering key components. Replacing a failed board can restore normal operation when the unit won't start, stops mid-cycle, or behaves erratically. What it does:

• Manages cycle timing and sequences based on selected options
• Distributes power to the circulation pump, drain pump, water inlet valve, heater, and dispenser
• Monitors inputs from sensors and the door switch to advance/complete cycles
• Faults can present as unresponsive controls, won't start/finish cycles, random resets, or error codes

• 1 electronic control board

• Disconnect power at the breaker before servicing; shut off water supply if accessing the lower compartment
• Use anti-static precautions; handle by the edges and avoid touching connector pins
• Access location varies by model; photograph wiring and transfer one connector at a time
• After installation, run the dishwasher's diagnostic/service cycle to verify operation

This clock control board is the electronic brain of your oven. It powers the display, reads keypad inputs, and controls bake/broil functions so you can set temperatures, timers, and cycles reliably. What it does

• Drives the time/temperature display and kitchen timer
• Interprets keypad inputs for bake, broil, and clean
• Sends power to heating circuits via onboard relays
• Manages alarms and fault monitoring

• Blank, dim, or garbled display
• Buttons unresponsive or erratic
• Oven won't start or won't heat despite good elements and power
• Random beeping or fault/error codes

• 1 electronic clock/control board

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use anti-static handling; avoid flexing or touching component pins
• Photograph and label all wire connections before transfer
• If your model uses a separate overlay/keypad membrane, carefully transfer it from the old board

This OEM part is a power control board. The power control board provides power to the electronic oven control board. If the oven is no longer turning on, or the digital display is no longer visible, this could mean it's time to replace the power control board. Luckily this is a relatively simple process.To begin, make sure to turn off the power to the oven by unplugging it or shutting off the circuit breaker. Then proceed to remove the upper back panel. Once removed locate the power control board and remove the wire harness and wires attached to it. Be sure to take note of the orientation of the wires to place them into the correct terminals on the new board. Attach the wires to the new board and snap the new board back in place. Resecure the back panel and put the oven back in place.This genuine replacement part is sold individually and is compatible with Bosch, Thermador, and Gaggenau ovens.

Electronic clock control for the oven/range. This board drives the display and manages bake/broil commands, restoring accurate timekeeping and dependable oven controls when the original control has failed.

• Governs oven operations by processing keypad inputs and signaling the heating circuits for bake and broil
• Displays clock, timer, and status information
• Monitors system feedback and can trigger fault alerts when issues are detected
• Common failure signs: blank or flickering display
• Oven won't start, won't respond to settings, or shows recurring control fault codes

• Disconnect power at the breaker and verify no voltage before servicing
• Use anti-static precautions; handle the board by the edges
• Note wire/connecter locations and transfer them one at a time; reuse any brackets/trim your model requires
• After installation, set the clock and run a test bake/broil; clear stored codes if applicable

Due to manufacturer changes please contact our customer service to verify this part is compatible with your appliance.

This electronic oven control board (clock/timer) is the brain of your range/oven, regulating temperature, powering the bake/broil circuits, and managing the display and keypad. Replacing it restores proper heating and responsive controls.

• Governs bake and broil circuits and maintains set temperature using oven sensor feedback
• Displays time/temperature and responds to keypad inputs
• Common failure signs: oven won't heat or start, erratic/inaccurate temps, dead or unresponsive display, repeated beeps or error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board by the edges and use anti-static precautions
• Photograph/label connectors and transfer wires one at a time to the new board
• Transfer the existing keypad overlay and any brackets as needed, reinstall panel, restore power, and test bake/broil

The Range Main Control Board Assembly is essential for the proper functioning of your range. This genuine OEM part ensures seamless control over all range operations, including temperature settings, burner functions, and indicator lights. Designed specifically for Samsung ranges, it provides a reliable and secure fit, making installation straightforward and hassle-free. The main PCB assembly is built with high-quality components to enhance the performance and longevity of your appliance, allowing you to cook with confidence and precision. If youGÇÖre experiencing unresponsive controls, inconsistent heating, or malfunctioning displays, the Range Main Control Board Assembly offers a dependable solution to restore your rangeGÇÖs functionality. By choosing this genuine OEM part, you are ensuring that your Samsung range operates smoothly and efficiently, maintaining the optimal performance you expect. Trust in this main control board to deliver a user-friendly and efficient cooking experience, keeping your kitchen running flawlessly.

The Control is an OEM part for Frigidaire ranges. It serves as the central control unit for the oven, allowing you to set and adjust cooking temperatures, timers, and other essential functions.

A bad oven control board can be caused by electrical issues, component failure, or damage due to power surges or other factors. When the control board becomes faulty, it can result in issues such as inaccurate temperature readings, unresponsive controls, or failure of the oven to heat up properly.

Symptoms of a bad control board include:

• Inaccurate temperature readings or inconsistent heating
• Unresponsive or malfunctioning control panel
• Failure of the oven to heat up or maintain desired temperature

Replace your faulty oven control board with this genuine OEM part to restore your range.
This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This relay board works with the main control to switch power to high-load oven components. Replacing a failing board can restore consistent heating and reliable performance across bake, broil, and convection functions. What it does:

• Switches high-voltage power to oven elements and fans as directed by the control
• Loss of heat in one or more modes (bake/broil/convection) is a common failure symptom
• Intermittent or erratic heating, long preheat, or heat stopping mid-cycle
• Visible burn marks or heat damage on the board

• Disconnect power at the breaker or fuse box before servicing
• Access location varies by model (rear panel or control compartment)
• Photograph wiring and move connectors one at a time to the new board
• Handle by the edges and use anti-static precautions; reuse existing hardware