Dishwasher Dishrack

We looked for a supplier of the part and came across AppliancePartsPros. They had the parts in stock and the prices were reasonable. We ordered the parts sometime on Thursday afternoon. The needed parts arrived on Friday around 11:00A. Wow, what fast service! Read more

While this is a Whirlpool dishwasher, I have the Kenmore Elite version of it. I believe them to be identical for parts. A little background: The first symptom I had of problems was plastic bits from the ball bearing retainer strips in the slides falling out. Then ball bearings falling out. A common problem with this dishwasher. When disassembling the upper basket, some of the gray plastic pieces were very brittle and easily snapped off. So I ended up replacing all of the plastic pieces related... Read more

Two years ago replaced all four roller assemblies of affected side. Problem recently reoccured on the opposite side. Replaced all four roller assemblies on that side. Entire repair took about twenty minutes. Read more

Dishes were 'gritty' with an almost invisible coating of specks smaller than grains of salt. Prior to ordering parts, I had to determine which part(s) needed replaced and which could benefit from a good cleaning. After viewing Appliance Parts Pros YouTube Videos, I removed the Main Manifold (snaps right off) including the Top Spray Arm. I discovered the Flappers of the Docking Station (AP6009888) were worn out and/or missing. I removed the Docking Station simply by popping the old one off... Read more

Bought a new baskit Read more

Having just moved into an older home with what seems like period appliances I knew I was in for some repairs on just about everything. Finding a site like Appliance Pro really helped me out with the ordering of the needed parts. A simple snap off / snap on with the help of some pliers did the trick and now the baskets are rolling like new. Read more

Order parts and replace. When removing attachments, do them one at a time and install them on new rack as you go. Watch for the small release tabs on the attachments (baskets, rollers and tine holders), "gently" put pressure to release; remember these units have been in hot water and they are brittle. Read more

Ordered new replacement tines from AppliancePartsPros.com. Just unsnapped the clips, removed the old rusted parts, and replaced them with the new parts I received. Read more

Turn off the power , pull dishwasher and replaced the new one . It is working now Read more

I bumped into my KitchenAid dishwasher and the upper rack adjuster cracked. There was already a crack on the notch of the housing where the handle (lever) sits. In addition, the positioner popped out and I couldn't find it. So, I bought the three parts from AppliancePartsPros online. It arrived in about a week. The repair was fairly simple, but it still took about 45 minutes because I didn't want to crack the assemblies. For the housing, use a small slotted screwdriver to carefully... Read more

The part just snaps on the basket. You have to remove the clips on the end of the runner arms to be able to remove the basket. Once it was out the old arm snap off and you snap on the new arm. Only problem was my old arm was fine and I wished the company would just sell the gasket. It seems a waste to have to purchase the whole arm. The complete job took me about 10 minutes from start to finish. I ordered the part online a Sunday afternoon and it arrived at my house on Tuesday. Read more

I ordreded the tine clip kit. APPros was the least expensive, even with the shipping charge, and I had it in two days. Replacement piece snapped into place with very little difficulty. I also have extras from the kit so I am set if another breaks. Read more

Took out 3 torx screws on each side, much of the insides fell out at this point. At this point I had the new part and what was left of the old part and the adjust lever. Screwed them back together and that was that. The new support piece was not needed. Read more

Took out 3 torx screws on each side, much of the insides fell out at this point. At this point I had the new part and what was left of the old part and the adjust lever. Screwed them back together and that was that. The new support piece was not needed. Read more

I replaced the flood switch assembly (thermistor unit). I, also, replaced some of the dish rack parts. It works perfectly now and my silverware does not fail through the bottom of the basket. The video was of great assistance. Read more

Replaced the lower rack Read more