Need Help?
Call
Plastic tube hanger that holds the upper dishrack in place inside your dishwasher tub. Replace if broken, cracked, or missing to restore proper rack support.
No tools required. One item was defected but Appliance parts replaced it immediately. Read more
Note: This is the complete solenoid assembly kit. For armature & linkage assembly only, use WD1X1316.
The Solenoid Assembly is an OEM part for GE dishwashers. It plays a crucial role in controlling the flow of water into the dishwasher by activating or deactivating the drain valve. This assembly is essential for ensuring that the dishwasher fills and drains at the correct times during the wash cycle, which is pivotal for the overall efficiency and effectiveness of the appliance.
Common causes for a Solenoid Assembly to fail include wear and tear over time, mineral buildup from hard water, or electrical failures that prevent the solenoid from operating as intended.
Symptoms of a bad Solenoid Assembly include:
This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
Put in the new parts and now it does not leak anymore. Very simple Read more
Fix a dishwasher that won't turn on or has non-responsive buttons with this control panel interface board. DIY-friendly repair, typically takes 20 minutes.
Replaced UI board and lower door gasket. Followed the instructions and luckily both the UI board and lower door gasket were in the dishwasher door. Took about 20 minutes and the GE dishwasher is now working like new again! Fast shipping and reasonably priced- thank you AppliancePartsPros.com! Read more
Protective cover panel for the bottom front of your dishwasher. Replaces cracked, bent, missing, or discolored kickplates to restore appearance.
The How-to videos on YouTube from appliance parts pros are very easy to follow. Read more
Supports and secures the upper spray arm in your dishwasher. Replace if cracked, broken, or detached. Clips to the bottom of the upper rack.
Note: This manifold has two holes on the part that mounts to the back wall of the dishwasher. For one hole use WPW10571949.
I discovered that the manifold was not connecting with the water supply,so the dishes in the upper tray were not being washed. This was caused because the rear hanger on the manifold had broken and it did not lineup properly into the water supply connection in the back of the dishwasher. I removed the manifold and found that it had two part numbers stamped on it. I searched on both part numbers and received a hit on the second part number. The photo looked exactly like my manifold so I... Read more
Dishwasher won't fill or keeps overfilling? The float switch detects water levels for proper filling and draining. Accessible repair in under 30 minutes.
I checked continuity at the float switch since I knew the inlet valve was working when direct wired to 120v. Switch did not have continuity. Replaced switch and inlet valve worked at start of cycle. Read more
Water pooling in your dishwasher after cycles? A faulty drain check valve allows backflow. This part prevents water backup and ensures proper drainage.
Since my Samsung Dishwasher would not drain and had a flashing quick light, I removed the racks and both spray wands. Which allowed me to remove the lower screen assembly. This revealed a worn and broken check valve and broken grinder blade. I cleaned the inside of the dishwasher and removed the unit from under the counter. I removed and cleaned the brake assembly ( large transparent plastic section on left side of the dishwasher). I cleaned this for preventive maintenance by taking the float... Read more
This is the lower spray arm that sits beneath the bottom dish rack in the dishwasher. It rotates during the wash cycle, spraying water through its jets to clean dishes on the lower rack. Replace this spray arm if you notice dishes coming out dirty, the arm is cracked or clogged, or it no longer spins freely.
Replaced part assembly. Read more
Covers the gap beneath your dishwasher for a finished look. Replace if cracked, broken, or missing. Installs at base with screws (sold separately).
Easy job, I screwed the parts to the dishwasher Read more
Replacement water inlet hose for dishwashers. Connects water supply to the tub. Replace if cracked, leaking, or damaged by pests or wear.
Replaced hose Read more
Detergent not dispensing or dishwasher door won't close? This dispenser module releases detergent at the right time. Moderate DIY repair difficulty.
Watched you tube video, fixed with no problem. Read more
Dishwasher leaking from the bottom? A cracked or worn inlet sump causes water leaks during wash cycles. Moderately difficult repair with video guidance.
Replaced with a new Inlet Sump [WD18X213]. It was a little tedious, attaching the Inlet Sump, back to the pump, because I did the job with the dishwasher in place (not pulled out). My dishwasher was plumbed with copper pipe, so I really didn't want to upset that. Also, I had previously replaced the motor and the pump in this dishwasher, so I was familiar with how the Inlet Sump attached to the pump. Again, it's very tight working under the unit while it is still in place, and I wouldn't... Read more
Fix a dishwasher that won't respond to button presses or has all lights stuck on. This control panel interface board restores operation. DIY repair.
Replaced the board and put it back together. Read more
Replacement silverware basket for dishwashers. Installs on the lower rack to organize flatware during wash cycles. Replace if cracked, broken, or missing.
Ordered a new silverware holder. Read more
The control panel on your dishwasher's door houses the cycle selection buttons and indicator lights. Replace if cracked, worn, faded, or missing.
Removed torx screws attaching stainless liner to outer stainless door. Lift off inner door and carefully separate the electronic components from where they snap into the control panel. Relocate electronic components to the new control panel. Reattach the inner liner with the torx screws. It is helpful to have an extra set of hands to hold the control panel while making the electronics swap to avoid pulling on the wiring harness. For door balance kit I just followed the video, straight forward. Read more
Lower spray arm distributes water beneath dishes on the bottom rack. Replace if cracked, broken, or missing to restore proper dish coverage.
Removed broken arm and snaped new one in place. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.