Dishwasher Pump

Includes motor, two o-rings and wire harness.

Sump assembly collects and channels a washer's drained water into the drain pump to let the machine empty properly. Replacing a worn or cracked sump helps stop leaks and restores normal draining performance. What it does:

• Directs and funnels tub water to the drain pump so the washer can evacuate water.
• Prevents water from leaking under the washer when intact and properly sealed.
• Can cause poor or no draining, standing water in the tub, or drain/pump-related error codes when damaged.
• May produce unusual noises during the drain cycle if cracked or clogged.

• Disconnect power and turn off water supply before starting any repair.
• Access typically requires removing the washer's front or lower access panel; support the machine as needed.
• Inspect and replace any worn seals, hoses, or clamps when installing to ensure a watertight fit.
• After installation, run a short drain/spin cycle and check for leaks before returning the washer to regular use.

The Circulation Pump for Dishwasher is designed to ensure your dishwasher operates smoothly and efficiently. This genuine OEM part guarantees a perfect fit and reliable performance for your Samsung dishwasher. It features robust construction that enhances water circulation, leading to cleaner dishes and optimal washing results. Easy to install, this circulation pump helps extend the lifespan of your appliance by maintaining consistent performance. Whether your dishwasher is experiencing reduced cleaning power or unusual noises, the Circulation Pump for Dishwasher provides a dependable solution to restore functionality. Trust in this genuine OEM part to deliver seamless operation and improve your overall dishwashing experience.

This replacement OEM part is a sump and motor assembly for dishwashers. The sump and motor assembly distributes water to the spray arm of the dishwasher. Luckily, replacing this part is a simple process. To begin, turn off the power supply and shut off the water supply valve. Remove the screws that secure the lower access panel. Disconnect the water supply line from the inlet valve. Then proceed to remove the mounting screws from the junction box cover. Take note of the wires' orientation. Remove the screws that hold the bracket. Disconnect the drain hose from the sink or garbage disposal. Open the dishwasher door and remove the mounting screws. Pull the dishwasher away from the cabinet and unsnap the covers from the hinge ropes. Disconnect the ropes. Remove the screws securing the upper door panel. Carefully tilt the dishwasher back and detach the fill hose from its retaining clip disconnecting the hose from the sump. Uninstall the sump and motor assembly and align the pump with the seal and sump. This genuine replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

Pump housing only. For a complete pump and motor assembly, order WPW10247394.

This drain pump assembly actively removes wastewater from the dishwasher at the end of each cycle. Replacing a failing pump restores proper draining, helps prevent standing water, and supports clean, odor-free performance.

• Pumps water out of the tub through the drain hose to the household drain
• Helps prevent water from backing up into the tub between cycles
• Common symptoms: won't drain/standing water, humming or buzzing during drain, intermittent draining, or leaking around the pump area
• Restores reliable end-of-cycle draining

• Disconnect power and turn off water supply before servicing
• Remove lower access panel; place a towel or pan to catch residual water
• Note wire and hose positions; transfer clamps and reconnect hoses securely to prevent leaks
• Inspect drain hose, air gap, and disposer/sink inlet for blockages before testing

This drain pump assembly removes water from the tub at the end of wash and rinse cycles, helping your appliance complete cycles and prevent standing water.

• Pumps wastewater out through the drain hose to the household drain
• A failing pump can cause slow or no draining, cycle interruptions, or error codes related to draining
• May also present as water left in the tub or an inability to start the spin/drain portion of a cycle

• Unplug appliance and shut off water supply before service
• Have towels or a pan ready—residual water will drain when hoses are removed
• Note wire and hose orientations before disconnecting; transfer any mounting hardware from the original if reused
• After installation, check for leaks and run a short drain cycle to verify operation

This de-coupled drain housing creates a sealed, vibration-isolated connection in the appliance's drain path. Replacing a cracked or leaking housing restores reliable draining performance and helps prevent water leaks and rattling during the drain cycle.

• Forms the rigid, sealed connection between the drain path and mating components
• Isolates pump vibration from the chassis to reduce noise during drain
• Directs wastewater efficiently out of the unit during the drain cycle
• Common symptoms of a failed housing include standing water, leaks under the unit, loud vibration/buzzing while draining, or visible cracks/broken tabs

• Disconnect power and water supply before servicing; allow any hot water to cool
• Access the drain area and place a towel or pan to catch residual water
• Move clamps/hoses, then transfer any reusable seals or grommets; replace worn seals as needed
• Secure all connections and clamps; run a short test and check carefully for leaks

This dishwasher circulation pump and motor assembly moves wash water through the spray arms during the cycles. Replacing a failed or noisy unit restores proper water flow, spray pressure, and reliable cleaning performance.

• Circulates water from the sump through the spray arms during wash and rinse
• Provides the pressure and flow needed for effective cleaning
• Common failure symptoms: little or no spray action, poor cleaning results, loud humming/rumbling/grinding during wash
• Water leaking from the pump area can also indicate a problem with this assembly

• Disconnect power at the breaker and shut off the water supply before servicing
• Access from the bottom/front; remove the toe panel and pull the dishwasher out if needed for clearance
• Expect residual water; place towels or a tray to catch spill, and note wire/connector orientation before removal
• Ensure all connections and seals are properly seated; run a short fill/rinse to check for leaks before reassembly

This circulation pump and motor assembly recirculates wash water through the spray arms so dishes get clean. Replace it to restore strong spray and quiet operation when the wash motor fails, becomes noisy, or leaks at the pump.

• Recirculates water from the sump through the spray arms during wash cycles
• Maintains proper water pressure and flow for effective cleaning
• Replaces a seized, weak, or noisy wash (circulation) motor
• Common symptoms: no spray or poor cleaning; humming or grinding from the pump; water leaking beneath the tub near the motor/pump

• Disconnect power and turn off the water supply before servicing
• Remove the toe panel; pull the dishwasher out as needed for under-tub access
• Place a towel to catch residual water; label/photograph wire and hose locations and transfer clamps from the original assembly
• Clean sealing surfaces; seat the assembly fully and test for leaks before reinstallation

This sump assembly is the dishwasher's lower-tub pump housing that circulates and drains wash water. Replacing a cracked or clogged sump restores proper drain and circulation, helping stop leaks and restore normal wash performance. What it does:

• Houses the pump and channels wash water for circulation and draining.
• Restores proper drainage when the dishwasher won't drain or holds water in the tub.
• Stops leaks that develop from cracked or damaged sump housings at the base.
• Reduces pump noise or grinding caused by debris, cracks, or a failing housing.

• Disconnect electrical power and water supply before beginning any service.
• Access the sump from the dishwasher's lower front (remove the lower rack and toe-kick/access panel as needed).
• Take care with wiring and hose clamps; transfer any motors, seals, or fittings only if required and follow manufacturer torque/placement.
• After installation, run a short cycle and inspect for proper drain/circulation and any leaks before reassembling trim.

The Drain Pump is an OEM part for Frigidaire dishwashers. It is responsible for removing water from the dishwasher tub at the end of each cycle. The drain pump works in conjunction with the drain hose to efficiently expel dirty water and ensure dishes are thoroughly dried.

Symptoms of a bad drain pump include:

• Water not fully draining out of the bottom of the dishwasher tub
• Puddles or standing water left inside after a cycle is finished
• Mildewy or musty smells emitting from the appliance
• Loud or grinding noises coming from the drain pump motor area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This motor-pump is the washer drain pump assembly that moves water out of the tub, helping your washer complete wash and spin cycles and preventing water from remaining in the drum. It replaces a worn or failed drain motor assembly to restore reliable draining. What it does:

• Pumps water out of the wash tub during drain and spin cycles.
• Circulates and forces wastewater through the drain hose and out of the machine.
• Common symptoms: washer won't drain, water left in tub after cycle, unusual humming, grinding or noisy pump, or intermittent drain failures.
• Can stop leaks caused by a failed pump seal or cracked housing (inspect plumbing/hose as well).

• Disconnect power and turn off the water supply before beginning any service.
• Drain residual water from the tub and hose before removing the old pump to avoid spills.
• Access usually requires removing the washer's access panel or front panel; handle sharp edges carefully.
• Reconnect wiring and hoses securely, check clamps, and run a short test cycle to ensure proper draining and no leaks.

For single drain outlet models only. For dual outlet port models you must order the complete pump and motor WD26X10013.

This impeller assembly replaces a worn or damaged wash-pump impeller to help restore water circulation and spray pressure for better cleaning. Commonly used in compatible Whirlpool wash pumps to address weak wash performance. What it does:

• Spins inside the wash pump to move water through spray arms; damaged fins reduce spray force and cleaning.
• Restores proper flow during wash cycles — symptoms of failure include weak or uneven cleaning.
• Reduces abnormal pump noise and motor strain when the impeller is intact; cracked or missing fins can cause humming or grinding.
• Works with the pump housing and seals to route water; a failed impeller can allow internal leakage or cavitation.

• Always disconnect power (and water, if applicable) before servicing the appliance.
• Inspect pump seals, gaskets, and surrounding components; replace any damaged parts to prevent leaks.