Dishwasher Switch

An integrated door switch for dishwashers that senses when the door is closed and allows the machine to start. Replacing a worn or damaged switch restores normal operation and helps prevent cycles from running with an open door. What it does:

• Detects door-closed position and tells the control board the door is secure
• Enables the dishwasher to start cycles only when the door is properly latched
• Prevents operation or pauses cycles if the door is open or not fully closed
• Common symptom: dishwasher won't start or stops mid-cycle when the door is opened

• Disconnect power to the appliance before attempting any service.
• Access typically requires removing the inner door panel or toe-kick; handle the door carefully to avoid damage.
• Replace the switch and reconnect wiring exactly as removed; ensure connectors are fully seated.
• After installation, restore power and ensure the door registers closed and the unit starts normally.

The Push Button Switch is an OEM part for GE dishwashers. It is an electro-mechanical button located on the control panel that allows users to select options and operate wash cycle features. 

Causes of a bad switch could be repeated pressing over time deteriorating the button mechanism. Liquid intrusion into the switch housing may also cause the failure of electronic components.

Symptoms of a failed switch include:

• The associated function no longer responds to button presses  
• Erratic or intermittent behavior when selecting options
• The switch button becomes stuck in the depressed position

Compatible with Hotpoint, RCA, and select Kenmore models as well, this switch helps prevent further control panel issues down the line.

This switch interlock assembly secures the appliance door and completes the electrical circuit so the unit can start and run safely. Replacing a worn interlock restores reliable door sensing and helps ensure normal cycle operation. What it does:

• Detects and holds the door/lid closed so the appliance will start
• Completes the electrical pathway for motor and control circuits
• Prevents operation when the door is open or not fully latched
• Can stop mid-cycle or prevent starting when the interlock fails

• One switch interlock assembly

• Disconnect power (unplug or switch off the breaker) before replacing the part
• Handle mounting screws and wiring harness carefully; match connector orientation when reinstalling
• Verify door alignment and latch function before restoring power

The Float Switch is an OEM part for Whirlpool dishwashers. It is a safety component that detects water levels and monitors flood conditions. The float switch ensures the dishwasher only runs water when needed and shuts off water flow if it detects a potential leak or overflow situation. 

Symptoms of a bad float switch include: 

• The dishwasher fails to fill with water or stop the water when the cycle is complete
• Loud buzzing or humming noises coming from the float switch area  
• Water leaks inside or outside of the dishwasher due to overfilling
• Repeated error codes related to flooding or water level detection

Causes of a bad float switch could be wear and tear over time, defective wiring or electronic components inside the switch, or damage from moisture or leaks. 

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This push button switch assembly replaces a worn or unresponsive control button to restore reliable user input on the appliance. It provides a firm tactile response so commands register correctly at the control panel. What it does:

• Acts as the user-facing push button that completes the control circuit when pressed
• Restores responsiveness when buttons are stuck, intermittently work, or fail to actuate
• Helps eliminate missed starts or unrecognized button presses at the console
• Fits into the control panel and interfaces with the appliance's internal switch contacts

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access may require removing the control panel; keep fasteners and trim in a safe place
• Handle connectors gently—disconnect and reconnect wiring harnesses by the plug, not the wires

This door-mounted switch detects when a refrigerator/freezer door is opened and closes the circuit to control the interior light and door-sensing functions, restoring proper light and access control. What it does

• Opens/closes the electrical circuit when the door is closed or opened to turn the interior light on/off
• Restores normal interior lighting when a failed switch causes the light to stay off or on
• Helps the appliance detect door-open/closed status for related functions
• Compatible with common door-frame mounting and wiring harnesses used on many Frigidaire units

• One door switch assembly

• Disconnect power before inspecting or replacing the switch to avoid shock
• Verify correct connector orientation and secure mounting before restoring power
• Do not use part if wiring or connectors are burned or damaged; replace harness as needed

Pressure switch that monitors water level and signals the washer control board when to start or stop filling. Replacing a failing pressure switch can help restore correct fill levels and normal cycle operation. What it does:

• Senses air pressure from the tub and tells the control when the correct water level is reached
• Stops the fill valve once the desired level is detected to prevent overfilling
• Can cause underfilling, overfilling, or failure to advance cycles when faulty
• Works with the washer's control system to ensure proper fill and cycle progression

• Disconnect power to the appliance before starting any repair
• Shut off water supply and relieve any trapped water before accessing components
• Carefully disconnect wiring harness and air tube; note routing for reassembly

A reed switch door sensor that detects when the appliance door is closed so the control can start cycles. Replaces a failed magnetic sensor to restore reliable door-closed detection and normal operation. What it does

• Acts as a magnetic contact that signals the control when the door or lid is closed
• Helps prevent the appliance from starting if the door is open or not fully latched
• Common symptom fix for no-start, intermittent cycle start, or control not recognizing a closed door
• Works as the electrical switching element in the door/detector assembly

• One reed switch (single replacement sensor)

• Disconnect power to the appliance before replacing the part to avoid shock or damage
• Handle the switch and wiring gently; avoid bending or stressing terminals and solder joints
• Locate and access the door/detector area per your service manual or tech sheet; confirm connector orientation before installing

A replacement selector switch that restores user control of temperature and function selection on compatible ranges and ovens. Designed to match OEM fit and restore reliable control response for common cooktop/oven functions. What it does

• Selects oven or burner functions when you turn the control knob.
• Routes user input to the appliance control circuits so the unit responds correctly.
• Commonly replaces worn or failed switches that cause unresponsive controls, no function selection, or intermittent operation.
• Helps stop erratic behavior like controls that click without changing settings.

• Disconnect power to the appliance before beginning any repair.
• Replacement typically requires removing the control panel and knob; handle wiring and connectors carefully.
• Verify knob orientation and switch alignment during reassembly.

A replacement switch assembly that restores proper electrical control for compatible Frigidaire appliances. Replaces a worn or faulty switch to help restore reliable on/off and cycle control for the affected function. What it does:

• Acts as the electrical on/off or selector switch for the appliance control circuit
• Restores reliable contact when original switch is intermittent or unresponsive
• Commonly used when the appliance won't start, specific functions won't engage, or controls feel loose
• Fits into the original control panel location and connects to existing wiring harness

• Disconnect power (unplug appliance or switch off breaker) before inspecting or replacing the switch
• Access may require removing a control panel or trim—keep fasteners and wiring orientation noted
• Handle terminals carefully to avoid bending or damaging contacts; confirm secure wiring connections before restoring power