Need Help?
Call
Fixes dryers showing error codes (E68, LOC), won't start, or unresponsive controls. Moderately challenging repair—most DIYers complete in under an hour.
Replaced control board. But couldn't move drier so had to reach top cover screws from front. Read more
If your dryer won't shut off or cycles incorrectly, the timer control is likely failed. This 10-minute DIY repair restores accurate cycle timing.
Replaced timer, cleaned out exhaust and lint collectors. It's running again."Nuff said! Read more
Fix a dryer that won't shut off or runs continuously. This timer controls cycle timing and automatic shutoff. Most DIYers complete in 15-30 minutes.
Installed this part and it was working good as new in 15 minutes! Read more
Fix a dryer that won't start, displays error codes, or won't turn off with this control board. Moderately difficult repair requiring basic wiring skills.
Fix a dryer that won't start, has a dead console, or runs erratic cycles by replacing the electronic control board. DIY-friendly repair.
On/Off switch was not working on our GE dryer. An appliance repair person told me he would charge $350 for the part and service. Purchased the part needed from AppliancePartsPros.com for around $130 (including S&H). The part was delivered within a few days and took literally minutes to install with socket set, pliers and a phillips head screwdriver. Read more
Dryer won't stop running or loses power intermittently? The main control board controls drying cycles and power distribution. Moderate DIY repair.
I fixed the problem by replacing the main control board Read more
Dryer stops mid-cycle or won't heat properly? A faulty timer often causes these issues. This timer controls cycle progression and heating phases.
Purchased a new timer from applianceParts Pros. Simple replacement took 15 minutes, dryer is running like new again. Also, defective timer made in china, new replacement made in USA. It just doesn't get any better than that! Read more
Fix a dryer that won't advance, runs continuously, or stops unexpectedly. This timer controls cycle progression and power routing. 15-minute DIY repair.
Just as the folks in the comments section said, I tested everything to make sure the timer had power which it did. I then tested with the OHM tester and saw that the switch was open when the timer was set to any drying cycle. So i changed the timer and voila! timer is functioning again. It was a very easy fix. Just pop the four screws out of the back of my timer panel on the dryer, detach all the wires, lift up on the little bracket that is holding the timer in place and twist it, and it... Read more
Dryer won't heat, won't shut off, or shows FE error? The main control board manages heating element relay and cycle timing. Moderate DIY repair.
Replaced Main PCB Assy. Read more
Dryer won't advance through cycles or keeps running after finishing? This timer controls cycle sequencing and shutoff. Typical DIY repair in 15 minutes.
Replaced timer. Took 15 minutes Read more
Fix a dryer that won't turn off or advance through cycles with a new timer. Controls cycle duration and automatic shutoff. Moderate DIY repair.
I ordered a new dryer timer. Read more
Timer won't advance or dryer runs continuously? This timer control restores proper cycle progression in auto and timed modes. DIY-friendly repair.
I ordered the timer and knob on Monday, they arrived around noon on Tuesday, and within an hour I had them installed and back in business. I was amazed how quickly the parts got here. The online video showing the procedure step by step was very helpful. Instead of disconnecting all the wires and having to keep up with which one went where, I moved each wire one by one and made sure I didn't get any of them in the wrong place. The only thing that slowed me down a bit was seeing which side of the... Read more
Dryer won't start, advance through cycles, or shut off? A faulty timer is often the cause. This mechanical control selects and advances drying programs.
Rebuilt it, belt, rollers, selector assembly, door switch, start switch. Read more
Dryer won't advance cycles or shuts off at wrong times? A faulty timer is usually the cause. This control restores proper cycle timing and progression.
Appliancepartspros supplied the appropriate materials and the installation was quick and easy. My GE gas dryer works like new again. Read more
Fix a dryer that won't advance cycles or turn on due to a worn timer shaft. This plastic-shaft timer restores knob grip and timing control. 10-minute DIY fix.
Checked for the problem replaces that part along with some parts as preventive maint app made it easy parts for perfect and were shipped very fast app is the only place to buy parts great place Read more
If your dryer won't shut off or cycles won't advance, the timer may have failed. This control manages drying cycles and run time. DIY repair in 20 minutes.
With a Phillips screw driver, on the back of the control panel there was about 6 or 7 screws to undo, to take the cover off and 2 screws holding the timer in place. Just undone those, took out old timer, made sure I took wires from old timer one at a time, and, put on new timer. Put everything back, although I had to find a couple of very small washers to make the timer fit tight, in the 2 holes it came out of. Luckily I had those or would of been a very loose timer. Very easy to do. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.