Need Help?
Call
Dryer not heating or flame goes out after igniting? This flame sensor monitors burner temperature to regulate gas flow. Easy 15-minute DIY repair.
Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more
Replaces worn or broken refrigerator door hinge bearing. Installs between door and hinge bracket to support smooth opening and closing motion.
I went to Appliance Parts Pros and watched a few videos. Ordered the door closer plate and door hinge bearing. Removed all of the door bins and contents. Removed four screws total. Lifted the door off of the hinge, replace the two parts on the bottom hinge. Put the door back on the hinge with a little silicone on the new parts. Replaced all of the screws and no more popping. It took more time to clean all of the door bins than to fix the hinge. The video was 100% accurate. No surprises. Read more
Idler pulley assembly for dryers. Mounts on the idler arm to keep the belt aligned and tensioned. Replace if pulley is worn, cracked, or squeaking.
The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more
Replace your range oven door seal when heat escapes or it's cracked. Seals oven perimeter for proper temperature control. Confirm fit with model number.
First i called sears parts direct to order this part, because that is where i purchased my electric range. they had an outrageous price of $98. unbelievable to think that such a small piece of rubber could cost that much. i also called a few other parts dealers on other websites. they also had high prices. when i called appliance parts pros they cut the cost by 50%. i am not sure if i could have found a better price because i stopped there. it is exhausting and time consuming to have to compare... Read more
Crisper pan for refrigerators. Stores fruits and vegetables in the lower compartment. Replace if cracked, broken, or missing for organized storage.
Used same tools as in your video. Read more
Burner won't ignite or sparks intermittently? This spark ignition switch and harness assembly restores reliable ignition. Moderate DIY repair.
First off thanks AppliancePartsPro.com... Another project in the books... I ordered a new switch harness and spark module because I just decided the why not do them both. They arrived very promptly, uses very simple tools most people have I would think. After unplugging it and shutting off the propane. I removed valve knobs. Then the burners with a nut driver and two sizes of sockets. The stove top and valve cover six Philips head screws. Gained complete access to the stove top. Removed... Read more
Compressor clicks and won't run? This start relay kit fixes refrigerators that won't cool. Common fix for clicking compressor that shuts off. Easy install.
Thanking APP ahead of time for expedient 1 day express parts & videos! I kept a LOG on this repair fix starting 6/21/20: started with cleaning out behind the Frigidaire /coils, fan blade, floor, walls, toe-plate, compressor. #1 Replaced just the Run Capacitor [from my local appl store]. Somewhat better but not a fix. Fridge controls need much higher settings than Factory Settings - which is recommended. Did some homework on several sites /kept coming back to yours / saw what parts are probably... Read more
The Bake Element is an OEM component for Frigidaire wall ovens. It is an integrated heating coil that generates heat through electric resistance when powered. Located near the bottom of the oven cavity, the bake element facilitates heating for various cooking functions like baking, roasting, or warming. This element measures approximately 13 x 11 inches. Symptoms of a bad bake element include:
Causes can be cracks in ceramic sheathing allowing arcing, or mineral deposits coating coils over extended use impeding heat transfer.
This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
First, I took an ohm reading across the elements and determined the bad one, which was failed, open circuit. (Zero continuity) I then replaced the lower heating element of the upper oven. Although the design of the oven and element make it appear that it will just drop down and slide out the front, this is not quite the case. There is not enough clearance for it to drop all the way down. You have to pull the entire double-oven unit out of the wall, separate the upper and lower halves a few... Read more
Idler arm assembly mounts near the dryer drum to guide and tension the belt. Replace if the pulley is worn, cracked, or causing belt misalignment issues.
Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more
The Door Handle is an OEM part for Frigidaire ovens. It is designed to provide a secure grip for opening and closing the oven door. This handle is white in color and 29" in length. Please note, the mounting screws are not included with the handle.
You should replace the door handle if it becomes loose, damaged, or broken. Causes of a bad door handle can include regular wear and tear from frequent use, exposure to high temperatures, or accidental impacts that cause cracks or breaks. Over time, these issues can make the handle less effective or unsafe to use.
Symptoms of a bad door handle include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
We ordered a new handle and two screws. The part was very easy to find and was in stock. Shipped out in 2 days and delivered by fed -ex. My teenage son put the handle on in less than 5 minutes. very easy. So happy we can finally use the oven again. Read more
Washer won't drain or has standing water? This drain pump actively removes water after each cycle. DIY-friendly repair, typically takes under 20 minutes.
Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more
Plastic bearing that acts as a pivot point for freezer door opening and closing. Replace if cracked, broken, or worn from repeated use over time.
Ordered parts and now works perfectly. Read more
Connects water filter to refrigerator system for clean water and ice. Replace if leaking, water flow is slow, or filter won't seal properly.
First we tried to change the filter. Water was leaking from the area of the filter when we changed the filter. We purchased an "original" Fridgidaire filter, no change. Did some research on the internet and decided to change the two tubes and the filter valve (at the back of the filter housing). Must have been the right diagnostic and the right part to make the repair, Gave me an opportunity to clean the condenser coils as well. After 6 years of service they needed it badly. Read more
The Flipper Mullion Assembly is an OEM part for Frigidaire refrigerators. It is an exterior part that seals the refrigerator door and houses the water and ice dispenser on select models. The flipper mullion assembly attaches both side by side doors together and operates the dispenser and door functions. Causes of a bad mullion assembly can include damage from door impacts, wear from years of door swing motions, or failure of seals or gaskets. Symptoms of a bad Flipper Mullion Assembly include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Started with replacing hinges. Had to glue the door hinge to refrigerator and secured with two small screws. This refrigerator is in a business with about 50 employees. Suspect minion was not working for some time causing the hinges to get broken. . Read more
Refrigerator not cooling properly? A broken condenser fan blade prevents heat removal from coils. Easy DIY fix—just pull off and press on. Video included.
No local refrigeration house had one. APP did! I got it in 2 days. Everything is A OK. Read more
Fix frost buildup on evaporator coils causing warm temps or freezer icing. This defrost heater melts accumulated ice. DIY repair in 30-40 minutes.
REPLACED DEFROSTER, CONDENSER FAN MOTOR AND DEFROST THERMOSTAT. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.