Electrolux Parts

Got the six year old refrigerator from my daughter because of it freezing up but was in good ( Stainless Steel) shape to replace our 21 year old Kitchen Aid. The thermistor had been replaced as a cheap first step but didn't correct the problem as it totally froze over within five days. I decided to tear down again and check the defrost heater element which was found to have an open circuit and hence the replacement part. Thanks to AAP, I ordered the part at the weekend, was shipped on Monday... Read more

Order the part to ApliancePartsPro and within 3 days I had it delivered to my front door. Looked up in their help page and was guided how to do it. It was so ease . I will recomend all my friend to get their parts at ApliancePartsPro. I am very please with the service and quality. Read more

The part just snaps on the basket. You have to remove the clips on the end of the runner arms to be able to remove the basket. Once it was out the old arm snap off and you snap on the new arm. Only problem was my old arm was fine and I wished the company would just sell the gasket. It seems a waste to have to purchase the whole arm. The complete job took me about 10 minutes from start to finish. I ordered the part online a Sunday afternoon and it arrived at my house on Tuesday. Read more

Based on my model # and serial # the Appliance Parts Pros were able to quickly find and ship the gaskets I needed. The instructional videos showed me how to remove the old and replace with the new. I was able to easily do it myself. Read more

Ordered left and right side supports and they arrived in two days! It took me longer to get stuff out of the way in the fridge so I could take the shelf out than it did to actually swap out the side supports. Parts fit perfectly and quick easy repair. Read more

Initially I noticed the crusher drum was cracked and broken so I replaced the drum the retaining nut on the end of the auger and the circlip and washer. it worked fine for a time and then the drum began free wheeling. upon further inspection I discovered the retain nubs on the auger had worn down allowing the blade to slip down the auger body. so I replaced the auger, drum, drive blade, and drive cam. I recommend if you gave a problem with the ice dispenser you break down and inspect the entire... Read more

Replaced both The electrical board I found under the fridge was very easy to replace. The fan motor took a minute to bed puns and the biggest challenge was taking off/on the back panel to get to it. (By the way it was located in the freezer section. take drawers out to get to it. Read more

Ordered new racks Read more

Replaced exhaust thermal cutoff switch. Sears wanted to charge for a service visit + parts and labor. $17 part, $6 shipping and I received the part the following day. Repair complete in less than an hour at a fraction of the cost. Thanks appliance pros. Read more

I ordered the oven control board, I was told that it would fix my problem. I installed it, which was extremely easy, and it worked. The oven worked flawlessly. Read more

Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more

I ordered a new kit and replaced it. It was easy except the video on the website did not include how to get off the front sticker. However, I did find another video to help Read more

Replaced the rack. Had to take some of the old parts that were still good and snap them into place.. pretty easy. Read more

Online chat here said that the oven sensor should be replaced. I got the feeling that was a bit off, so I went with my gut and ordered the thermostat as well. Replaced the sensor and that didn't fix it. Replaced the thermostat and it worked like a charm! Disappointed that they were overconfident in their answer and it would have taken me more days to fix - but, the products came in quickly (basically, next day) and were correct. Online video for my particular oven was incorrect - but it's... Read more

• Door won't open or close
• Door sweating
• Clicking sound

I went to Appliance Parts Pros and watched a few videos. Ordered the door closer plate and door hinge bearing. Removed all of the door bins and contents. Removed four screws total. Lifted the door off of the hinge, replace the two parts on the bottom hinge. Put the door back on the hinge with a little silicone on the new parts. Replaced all of the screws and no more popping. It took more time to clean all of the door bins than to fix the hinge. The video was 100% accurate. No surprises. Read more

I replaced the Blower Wheel Assembly. Read more