Electrolux Parts

Order the parts...!!! Read more

Replaced the Thernistor and resolved the problem. Took less than 15 mins to do if you follow the instructions that they have on this site. Great video! Thanks Read more

Removed door, pulled out old hinge bearing and replaced with new one. Read more

Ordered new Ignitor / Orifice and screws Mike was a great resource, he helped me thru the project. Read more

Repair man said that the part alone would cost more than $300.00. I checked it out on YouTube and saw that the actual replacement was an easy task. I contacted appliancepartspros.com and spoke to Wendy, who sorted me out with the correct part which arrived in two days ($115.00). It took me less than 15 minutes to replace the part, no more leak. Thanks appliancepartspros.com and Wendy for your cost effective and speedy service. Read more

Removed the bottom tin work in the oven and removed the burner tube. Tried to remove the igniter bracket but the screws were too tight for the Phillips head and couldn't get vice grips to clamp on the head, so I bent the bracket enough to remove and replace the igniter. Then reassembled. I give AppliancePros.com a 5 star rating. Site was easy to use, the part was delivered in under 2 days, and it was the correct part packaged carefully so the igniter was protected from breaking. Read more

APP has easy to search parts catalog fast shipping and genuine parts. Problem solved Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Leaking

This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more

Ordered new ice maker ,,, losen 2,, 1/4" screws on ice maker mountingbracket,, you dont have to remove screws just losen ,,disconnect wiring harness from back of old ice maker.. Take new ice maker connect wiring harness ,,mount ice maker back on 2 screws then tighten . Read more

Removed old plastic rack rollers and reinstalled new ones in their place. They did not match exactly to my rack model and I needed to cut grooves in the back side to fit them correctly. But was able to make it fit in the end and it works fine. Read more

Ordered parts on Monday, they arrived on Wednesday. Very very pleased. Read more

Replaced the rear drum bearing assembly and the front top felt that the drum rides on and since I has it apart installed a new belt. Simple to do and takes very little time! Read more

The glue behind the keypad loosened and the keypad slowly began slipping down out of place over several months. Finally, because of the movement, it warped which resulted in one of the keys being stuck. That is what gave the F12 error code. The fix was easy. I removed the control panel and then peeled off the keypad. The keypad itself then has two layers (1), the flexible circuit panel, and (2) the outward facing display. I separated the display from the circuit panel and put the new one... Read more

• Shakes and moves

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

• Door won't close

My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more

I removed the fresh food ice maker found the drain tube for ice maker frozen. This was causing the back of the unit to rust out. This also caused the water to run down the back of the unit the into the duct work and into the freezer causing ice buildup. I then defrosted the freezer removed the rear duct work and the freezer drain pan cover. I found the freezer drain was not draining. I removed the exterior rear cardboard cover and located the freezer drain tube removed it and found that it was... Read more