Frigidaire Gasket & Seal

Removed old rubber door gasket, replaced with new gasket. No tools needed. Read more

I watched the video on this website and did the repair Read more

Replaced the gasket. Five minute repair after door removal. Working great now. Read more

Purchased new gasket from your site. Watched the video for how to change it.Took about 15 min. to remove the old one and install the new one. Read more

Replaced gaskets on fridge. Read more

First i called sears parts direct to order this part, because that is where i purchased my electric range. they had an outrageous price of $98. unbelievable to think that such a small piece of rubber could cost that much. i also called a few other parts dealers on other websites. they also had high prices. when i called appliance parts pros they cut the cost by 50%. i am not sure if i could have found a better price because i stopped there. it is exhausting and time consuming to have to compare... Read more

Bought a new one and installed it - an easy job! Read more

• Door sweating

My co-worker bought a house to flip and gave me the refrigerator. I'd been looking for a garage refrigerator to store water, cola, etc in. Fridge was essentially fine but I sanded and painted one side which had rust spots. Turned out like new. The door seal was moldy and didn't seal properly. The only advice I can lend is to take the door off the hinges and lay it down flat. So much easier. With this seal you basically just take out all the screws, peel off old seal and set the new one... Read more

• Marks left on clothes
• Noisy

I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose." The cause of the scraping and loud... Read more

• Frost buildup

Arrived on time and was a good fit. no problems at all thank you Read more

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

Replaced door seal. Perfect fit, easy installation. Read more

Removed old bellow following procedures found on relevant Youtube videos. Reinstalling however was more of a challenge. Getting the rear seal of the new bellow on the washer housing was not as easy as the videos indicated. The key to that process is being sure the seal is well lubricated which is not quite apparent from the videos but is essential success. Once the rear seal is installed, reapplying the rear spring was accomplished with the spring clamps as per the videos. Be sure to... Read more

My 12 year old Frigidaire stack on top dryer had been beeping distress messages in some unintelligible code for about a year when it completely stopped producing heat. It also had a long standing issue with delicate fabrics and thin straps or drawstrings getting caught in the drum. After using this site to troubleshoot and viewing the useful how-to videos, I ordered and replaced the heating element, thermal limiter, and felt seals. Based on others' stories, I decided to also replace the rear... Read more

Gasket and liner arrived as planned. Clips were a day later. Used "hog ring" pliers to remove the clips, worked great. Pre-punched holes in the gasket did not match the original but the plastic liner did. Used an ice pick to punch the gasket and inserted the clips. This is a chest freezer, so install the hinge side first. Read more

Replaced the upper spray arm tube with a new one. Also replaced delivery tube grommet and the delivery tube gasket. Now everything works fine and no more leaks. Read more