Frigidaire Parts

I researched online and found that it was probably one of two things wrong: the heat probe or the control board (clock). Since the probe was less expensive, I ordered that on Appliance PartsPros. It arrived SO quickly, and with the repair video I easily replaced it. BUT... it still got the F10 reading. Sigh. So I found a local appliance repairman (I didn't want to replace a more expensive item if it turned out I was wrong). He was a good one: he listened to my story, said he was sure it was the... Read more

I ordered the replacement part. Your website was the only one I searched which exactly identified the correct part for me to order. The exploded diagram with numbered parts was very helpful. Read more

• Will not drain
• Noisy

So, Saturday, the washer wouldn't drain, yes, I tried the Drain/Spin cycle. So I took the clothes out, rinsed them out twice in the laundry sink and dried them. After a quick Google search, I came to the conclusion that the pump was bad and ordered a pump, $125. Over the course of the next four days, expecting the new pump on Thursday, I baled out the washer, pulled it out from the wall and propped up the front (it's HEAVY), removed the front access panel, removed the drain inlet and outlet... Read more

If you can't pull out the displacement pins on the crisper cover support clips that allow the wall to carry the weight of the cover, slides and drawer, you may need to push those pins in (they fall down the wall) to remove the clip. During the replacement of both front clips, I had one I could remove and one I had attempted to drill a tiny hole in to be able to pull the pin. Ultimately it did not work and needed to be simply pushed in. Do not worry, there is nothing below which the plastic... Read more

I ordered new parts from your company for my refrigerator. These were easy parts to replace and did not require tools. I was most grateful in being able to order those parts by telephone from your company. This process was surprisingly easy and did not require a long wait to speak to a representative. The persons I spoke with were polite, efficent and very competent. The parts got to me very quickly in well packed boxes. I though this process would be an ordeal and it was the opposite. This was... Read more

I believe we had two problems. Our gasket was ripped in several places and our drain pan line was clogged. Therefore the water was frozen and backing up into the freezer. Replacing the gasket is an easy job and could possibly be done quickly enough that you don’t have to remove your freezer food items if you don’t discover additional problems during the process. The most time-consuming part is the approximately 40 screws that hold the freezer door shelf panel and gasket to the door itself. ... Read more

My 12 year old Frigidaire stack on top dryer had been beeping distress messages in some unintelligible code for about a year when it completely stopped producing heat. It also had a long standing issue with delicate fabrics and thin straps or drawstrings getting caught in the drum. After using this site to troubleshoot and viewing the useful how-to videos, I ordered and replaced the heating element, thermal limiter, and felt seals. Based on others' stories, I decided to also replace the rear... Read more

They just slide in place. One shelf was broken and I had to reorder. Received the replacement within 48 hours. Read more

• Spins slowly
• Burning smell
• Pumps but will not spin
• Will not agitate

I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more

Ordered a new seal, and replaced it with a new one freezer works great now. Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

Noticed Rolls on the top shelf no longer frozen, though the meat around it still was. Note: This is a good test, keep something that thaws quickly and is not expensive on top shelf, to act as a barometer for your freezer health! I first found a trip online to advance the defrost timer, as a failed timer is a common issue. I advanced the timer, but nothing happened. I emptied the freezer, then removed the thermostat and tested it. No continuity! With the Freezer continuing to thaw, I... Read more

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

Based on my model # and serial # the Appliance Parts Pros were able to quickly find and ship the gaskets I needed. The instructional videos showed me how to remove the old and replace with the new. I was able to easily do it myself. Read more

Ordered part from your website. Fit perfectly Read more

Put racks to together and put into fridge Read more