General Electric Refrigerator Parts

My husband unscrewed the the glide bucket and easily attached the new one. It was however somewhat difficult to re-attach the mechanism behind the ice bucket (that turns the auger) to the glide bucket. He finally figured out that a screw had also snapped off from the glide bucket and was still attached to the mechanism. Once he figured that out he got it re-attached easily. Now here is something stupid we both did. After everything was re-attached, the motor didn't work that turns the... Read more

• Won't start

I am a 76 year old woman and hesitated to tackle the job. But my son sent me a Utube video "how to replace the board," and I was able to replace it, surprisingly, quite easily. I could have done it in a shorter period of time, if I had not been challenged with these arthritic hands and fingers. The refrigerator is now holding the temperatures quite nicely. Joan Read more

• Fridge too warm

The defrost heater element looked good and had continuity. The defrost thermostats checked good, so that just left the Defrost Module as the likely suspect. I installed a new defrost control module and thermostats. The thermostats were inexpensive and the old ones could have been intermittent, The only "tricky" part was finding out how to get to the back screw that holds the main control panel. Discovered that the return air duct surrounding the control panel needed to come off. It helps... Read more

Replaced both with the parts ordered from Appliance Parts Pros. Read more

Replaced defrost heater, temperature and defrost limiter thermostat. After taking the cover off the air chiller I found the coils frozen solid and defrosted it with a hair dryer. Once defrosted I remover the heater coil to test it it was fine, then I could see the defrost limiter was broken and as I put the unit back together I broke the heater tube (it is glass) so I ordered all the parts that might be defective and replaced them for less than the charge of having some one come to check it out. Read more

• Fridge too warm

Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more

BEWARE THE HAIRDRYER In an effort to unfreeze the indoor water supply line with a hairdryer the extreme heat deformed not only the activator paddle but the housing that surrounds it. In the time it took to order and install replacement parts the frozen blockage had thawed. Back in business for now and if the problem reoccurs I will be looking for a different path to resolve the issue. Read more

I checked the freezer and found the door gasket was damaged. When the parts arrived, I checked them for a good fit and the attachment method. Due to past experience of replacing door gaskets, I was expecting a lot of screws that would have to be removed and replaced. To my surprise, the gaskets pressed in place without tools and had a good and secure fit. The instructions the came with the gaskets suggested the hot water be used as needed to remove any kinks that might cause a poor fit. I... Read more

I went on line and read your advice page. Based on that, I removed the damper assembly (six screws counting the miserable light fixture) and found the damper door broken as predicted. I went back to your page and ordered the new part. Nice breakdown to get number. After that, I disassembled the damper assembly, found that the ABS plastic damper had broken from the actuator probably as a result of fatigue from cycling back and forth for twelve years. I used super glue to re-attach the damper... Read more

• Light not working

I researched the model and watched a YouTube video on the repair. I ordered the part. Two days later it arrived and I made the repair. I'm all thumbs in home repairs, but had it done in 5 minutes. My husband was surprised. Nice that I can take care of a few simple repairs around the house. Read more

• Fridge too warm
• Fridge runs too long
• Freezer not defrosting
• Freezer section too warm

My GSS20IETD BB side-by-side refrigerator had been having the ice form into a single mass over a period of a week after cleaning it out. It actually kept breaking my ice maker auger and pushing the slide-in tray or shelf over the ice maker up breaking it also. Frost would form all over food after about a couple of weeks. The ice auger motor would freeze up and stop turning. The coils did not have frost on them when I was able to view them. I replaced the thermistors in the freezer, defrost the... Read more

Condenser fan stopped on my big 2003 Monogram 4 foot wide ZIS480D Refrigerator. It is top mounted. The fridge had to be rolled out. 20 screws removed and the top sheet metal to get at the condenser. That was the only way to get at it. Works like new now. Read more

Watched the video to trouble shoot the problem. Still didn't work. Looked at the cost of new ice maker and watched another video on how to take it apart. Super easy, Only problem was the recommended replacement part did not look like what we had so took a chance and went with the one that that wasn't recommended but looked exactly like ours. Working perfectly now! Read more

Replaced two drawers, one shelf front, and the grille base Read more

Our refrigerator takes care of my wife and I, along with our children when they visit, and the grand kids. Over the years, it's seen its fair share of wear and tear. Thankfully, nothing major has happened that hasn't been able to be repaired right here in the home, and by me. Our refrigerator is a GE side-by-side with an ice maker/water dispenser, and has held up well. I've ordered parts for it from AppliancePartsPros.com for all of its repairs, and while GE/Frigidaire have been changing out a... Read more

Removed top hinge screws. unplugged connection. removed bottom hinge. Plug in connection and install srews into hinges Read more