Hose Or Tube

These replacement 6" FXF vacuum bags capture dust and debris to restore pickup performance and keep the appliance's airflow and motor compartment cleaner. Designed as a direct-fit consumable for compatible bagged upright and canister vacuums. What it does:

• Collects dirt, dust and debris so particles stay contained for easier disposal
• Helps maintain suction by keeping the vacuum's intake and motor chamber clearer
• Reduces dust and allergen re-distribution compared with a torn or overloaded bag
• Replaces worn or full bags that cause reduced capacity, visible dust escaping, or increased odor

• Always unplug the vacuum before removing or installing bags
• Remove the full bag carefully to avoid spilling debris; seal and dispose per local regulations
• Verify correct orientation and secure fit before operating to avoid leaks
• Replace bags regularly; inspect the inlet collar and seals for wear when servicing

This 6-foot rubber hose provides a flexible, durable connection for appliance water/drain routing, helping restore proper flow and reduce leaks. Designed as a direct replacement hose where a 6' rubber line is required. What it does:

• Replaces worn, cracked or brittle 6' rubber hose to stop or prevent leaks.
• Restores flexible routing for water supply or drain lines that need a 6-foot rubber connection.
• Helps eliminate kinks and restricted flow caused by damaged hoses.
• Compatible with standard hose clamps or quick-connect fittings used on many appliances.

• Turn off water and power to the appliance before starting any work.
• Inspect fittings and clamps; replace clamps if corroded or damaged for a secure seal.
• Push hose fully onto the fitting and secure with the proper clamp type; test for leaks before returning appliance to service.

This replacement fill hose carries incoming water from the washer's inlet valve to the tub or dispenser, restoring proper water delivery and preventing leaks. Use when the original hose is cracked, split, or leaking. What it does:

• Channels water from the inlet valve to the washer tub or dispenser during fill cycles
• Prevents leaks and drips caused by damaged or brittle hose material
• Restores proper fill behavior when a worn hose causes slow or no fill
• Works with the washer's inlet fittings and clamps to maintain a sealed connection

• Disconnect power and shut off the water supply before starting work
• Inspect and replace clamps or O-rings if worn; tight, corrosion-free connections help prevent leaks
• Route the hose to avoid kinks and pinching; secure with existing clips or ties
• After installation, restore water and power, then run a short fill cycle and check for leaks

This replacement water-supply hose routes water from the house supply to the refrigerator's dispenser and icemaker, restoring reliable water flow and preventing leaks at a damaged or clogged hose. What it does

• Carries cold water from the household supply to the refrigerator dispenser and/or icemaker
• Restores normal water flow when a cracked, pinched, or clogged hose prevents dispensing or ice production
• Helps stop leaks caused by brittle or split hose material at bends or connection points
• Works with the refrigerator's factory inlet and fittings to maintain pressure delivery

• One replacement water-supply hose

• Shut off the refrigerator and turn off the household water supply before replacing the hose
• Inspect connection fittings and replace any damaged clamps or seals for a watertight fit
• Tighten connections by hand then snug with pliers—avoid overtightening which can damage fittings
• After installation, slowly restore water and check all connections for leaks

Drain hose assembly that connects your dishwasher pump to the drain system. Replace if cracked, leaking, kinked, or disconnected from the pump fitting.

This U-shaped mounting bracket secures and guides the drain hose at the back of the washing machine, keeping it properly positioned during the drain cycle. It prevents the hose from slipping out of the standpipe or laundry tub. Replace this bracket if the drain hose keeps falling out of position, water is spilling during the drain cycle, or the original bracket is cracked or broken.

Water intake hose connects to your washer's water inlet. Replace if cracked, leaking, kinked, or showing wear. Essential for proper water supply.

Routes defrost and condensation water from your refrigerator to the drain system. Replace if cracked, split, or clogged to prevent water pooling.

Lower drain tube for top-mount refrigerators. Channels defrost water from evaporator to drain pan. Replace if cracked, clogged, or leaking moisture.

Replaces cracked, leaking, or worn drain hoses in your dishwasher. Creates the required elevated loop to prevent backflow. Essential for proper drainage.

Replacement water supply tubing for refrigerators. Installs between water valve and ice maker or dispenser. Replace if original line is brittle, kinked, or leaking.

The Hose is an OEM part for Whirlpool dishwashers. It connects the dishwasher pump and sump, functioning to drain and recirculate water throughout cycles.

Causes of failure can include mineral buildup inside the hose, splitting, and cracking of the lining from continuous heat and pressure usage over time.

Symptoms of a bad pump to sump hose include:

• Inadequate drainage and water removal from cycles
• Standing water left in the bottom of the dishwasher tub
• Leaks developing from hose connections at the pump or sump area

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Drain hose connects your dishwasher drain pump to household plumbing. Replace if cracked, kinked, clogged with grease, or leaking during drain cycles.

Plastic water line tube that connects the water filter to internal refrigerator components. Replace if cracked, leaking, or damaged to restore water flow.

Flexible drain hose that channels water from your washer tub to the drain outlet. Replace if cracked, leaking, abraded, or damaged during installation.