Kenmore / Sears Parts

• Door sweating
• Door won't open or close
• Clicking sound
• Fridge too warm

Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more

Thanks to the Appliance Pro video and next day delivery, the fix was easy. Removed the old seals by hand and placed the new seals around the door shelves and eased it into the grove in the door. Read more

Found the correct replacement in your easy to navigate parts lookup, ordered part, arrived sooner than I expected, Needed a nut driver to remove old part, unplugged harness, plugged new part in , retightened three screws and began making ice. Very clean and simple process. Thanks guys, I couldn't have done it with out you Read more

I ordered a replacement part. Emptied the top shelf then took the shelf out. Flipped the shelf over and removed the screw holding the broken piece. Put the new piece in its place replaced screw. Put the shelf back in and then put the mean pan back on the hangers. Read more

• Fridge too cold
• Fridge runs too long
• Won't start
• Freezer section too warm

The 20 year old unit still serves us well, looks good and has been kept in good repair. The condenser fan had stopped so I removed, cleaned and oiled that motor. The decision was made to make an upgrade to the evaporator motor and control units so that the appliance could reasonably be expected to have extended service life. The Ice maker module had been replaced 7 years ago. I ordered the parts and have made the upgrade for temperature controller and the defrost control. If you are in a... Read more

Removed freezer door by removing 4 bolts holding slide tracks for freezer basket. Pulled out old gasket. Soaked new gasket in hot water to smooth out a crease that resulted from shipping. Installed new gasket, starting at corners. Used a blunt tool to push new gasket into slot at the corners. Set remaining gasket material with hands. Used putty knife to tuck edge of gasket under lip along door. Reinstalled door. Take care to line up door perpendicularly. There is some play when... Read more

After about 6 months of use with our Whirlpool Cabrio washing machine it started to sound extremely loud in the spin cycle, we should have called Whirlpool at this point to have it looked at under warranty. Fast forward 5 years later our loud washing machine ended up leaking out the bottom, we had a local service company come out to take a look at doing the repair and they quoted $800 to replace the outer tub assembly. I was not going to pay $800 and figured that most likely we would purchase a... Read more

Replaced control board myself. Easy. Read more

Purchased new from you. Ordered Thursday at 4 PM and arrived next morning at 11AM using standard shipping. Did not require any repair...simply remove and replace BEAT THE DEVIL OUT OF YOUR ADVERTISED AVERAGE 1.7 DELIVERY TIME! GOOD JOB!! Read more

To say using Appliance Parts Pros made things as simple as it gets, is an understatement. I was able to order the parts simply by using their website and having my dishwasher make and model number. Images of the parts make confirming the order even better. They have an on line question/answer cue if needed and even offer a call in for advice number. Once the order arrived, I verified the parts and began installation. Take a few pictures of the appliance from different angles before you start.... Read more

• Ice maker dispenses too little ice
• Not dispensing water
• Ice maker won't dispense ice
• Ice maker not making ice

By visiting your website, viewing the repair instructions and ordering the right parts. Very easy to understand and to do the repair.. Read more

Installed new agitator Read more

• No heat or not enough heat
• Takes too long to dry

Our 25-year-old Whirlpool dryer abruptly stopped producing heat, though it was otherwise running normally. The unit had never required service of any type and we were reluctant to replace it. After confirming that no circuit breakers had tripped, I reviewed the Whirlpool and AppliancePartsPro websites and concluded that the most likely causes of the problem were a failed heating element and/or thermal fuse. I ordered both (they arrived in two business days), installed them and the dryer... Read more

Watched the attached video, then followed directions and installed the part ordered. Read more

• Marks left on clothes

Maytag Gas Dryer Model: MGDE300VW1 I had previous experience with repairing my dryers, but this was a first for this model. Instructional videos very helpful. Ordered necessary parts and they were delivered with-in two days. Wow! Squeak found to be coming from idler pulley roller which no longer turned freely . The four other cabinet rollers had signs of wear. Dryer belt had frayed edges and a couple of burn spots in the belt from the motor turning before the drum did. Cleaned up all shafts... Read more

The part went on easily. U Tube video answered any questions I had before installing. Read more