Maytag Parts

Just like the one's I have worked on for 30 years for Whirlpool. Read more

• Door sweating

The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable... Read more

Left new gasket on the table overnight so it could stretch out. Removed the door. Temporarily replaced it with plastic and tape. Pulled off old gasket. Cleaned surfaces with decreaser and wiped dry with paper towels and alcohol. Inserted new gasket. Replaced door. Read more

I searched online for replacement parts and Appliance Parts Pros had the part in stock. Before I ordered the part, I watched the video to see if I could handle the repair. I ordered the part and soaked the gaskets with warm water in the tub. The old gaskets had a much simpler setup, so no cutting was involved. I simply pulled the old gasket out of the track without issues, and installed the new one with finger pressure. Per the video, I took both doors off. However, due to the design, I could... Read more

• Shakes and moves

We looked online at AppliancePartsPros.com under the symptoms and found it was most likely caused by the shocks. Of course there was a repair video showing how to replace all four shocks step by step, and there was a link for purchasing the four shocks at the bottom of the video. Our repair didn't go quite as quickly as on the video because we are novices, but we were able to do the repair ourselves and, once again, saved ourselves a ton of money! Now we have a very quiet washer and dryer again... Read more

Replaced Read more

I bought replacement parts Read more

• Little to no heat when broiling

Ordered a new part. Watched a YouTube video. Fixed it in 15 minutes. Knowing you need to stop the connectors from slipping into the back of the oven was the key. I used paperclips to stop the wires falling through the hole. Easy as ... Read more

I ordered new crisper drawer. Diagram made it easy to see the correct drawer needed. Received the drawer promptly. Read more

Remove the ice bucket remove screws from one side of shaft remove screws from other end of shaft replace moter easy fix Read more

• Ice maker not making ice

I used your online troubleshooting tips and watched the videos on your site. I determined my thermostat was defective, ordered the thermostat which arrived in two days and I replaced the thermostat and I now have a full bin of ice !!! The do it yourself video was extremely helpful and made the repair very easy. Thanks so much for the great service and quick delivery !!! Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

I referenced the repair video. Very straightforward and easy. Only need 3 tools: 1/4 and 5/16 nut drivers and Philips head screwdriver. About 15 minute job. Surprising how much lint and dust build up inside the chassis, was able to clean that out too. Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

I ordered the tub seal and stem seal kits along with the much needed spanner wrench. After viewing the video online several times and taking notes along the way I was ready to tackle the repair. After taking everything apart, I cleaned all areas thoroughly then addressed the rusty areas and mineral deposits found in the tub. Soaking the tub in vinegar and baking soda overnight helped loosen the built up deposits enough so I could carefully scrape them off with a spatula. This was very time... Read more

I end up take the top and front lid of the dryer in order to gain access to the drum, belt, and motor. i put the belt on and closed it all back up again. Read more