Maytag Parts

Although I only needed to replace the drawer support (end cap) on the right side the kit comes with replacements for both sides. I was surprised to see that the air flow adjustment mechanism that is located on the right side end cap was not included. I should mention that I did not disassemble the drawer mechanisms before ordering the end cap(s). The kit contained only the two molded end caps - no fasteners, mechanisms, or anything else. It turns out that this was all perfectly fine. The... Read more

Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Replaced the water valve. Easy repair. The repair video was spot-on. Tools needed: Slip joint pliers for removing and attaching the hoses and moving the hose clip. 5/16 nut driver. Phone to take a picture so I could get the wires put back right. Shut off the water and unplug from power. Remove the hoses. Using a 5/16 nut driver remove the single screw that holds the bracket, lift bracket slightly and pull from the washer. There is a little slack in wires and fill hose to work with. Take a... Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

Removed one and put the other one Read more

Replaced it with a new seal Read more

Viewed YouTube video of AppliancePartsPros.com replacing the agitator to see if I could do it myself. I ordered part from Sears but they never delivered. Cancelled order with Sears, ordered from APP and was sent part within 24hrs by fedex for less than Sears charged. Will only go APP and would recommend APP to everyone. Using the video I easily replaced the part and our washer is back in business! Thank you APP!!!!! Read more

Removed washer lid, then upper front panel with controls. Popped off the front retaining ring, then pushed the boot into the washer area after detaching the detergent hose and LED light from the boot. Detached the door lock mechanism. Removed the front panel with the door. Then removed main retaining ring after loosening with Phillips head screwdriver. Removed the old boot. I found a bunch of nasty stuff in the cavity between the main drum and rotating drum which was blocking the boot from... Read more

$4 part and a little time saved $250 if I had had to replace the whole plug-in duel burner unit for our Jenn-Air range. Spade that was replaced fed both burners, other two spades just one. If your burners do not turn on, check the spades before you replace the coils. Read more

I bought replacement parts Read more

I took apart the old bucket with a screwdriver and put the new one with no problems. Read more

The hardest part was getting on my knees to do the repair/replacement. It was obvious debris wasn't being filtered out when the water was recirculated. I noticed the accumulator wasn't seating right and found the plastic clips on the backside were bent and worn. The new part came within a day and a half. Everything either unscrewed and snapped together with no tools. You may want to use a flat screwdriver to take the upper arm tube feed loose from its clips but it can be done by hand. Done... Read more

• Marks left on clothes

After replacing thermal fuse once and having it fail a second time, I had to dig a little deeper to uncover the problem. I checked for blockage in the vent but everything was clear. I did, however, find that the drum had some up and down play in it. After closer inspection, I could see that the front drum seal was actually worn to the point that I could see a gap between the seal and the drum. I figured that the gap in the seal was letting air in and not letting sufficient air flow through the... Read more

Called in. Talk to a sale rep. Told them the model number, told me that this part would work. Shipped it to me. Snapped it in about 30 seconds. Part was perfect. Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

• Will not stop filling with water
• Leaking

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more