Lg Disconnected Damaged Wire Harness Parts

This replacement lamp socket holds and powers the appliance light bulb, restoring clear, reliable illumination when the light is switched on. Replace a heat-damaged, cracked, or loose socket to stop flickering or a light that won't come on.

• Holds the bulb securely and supplies electrical power
• Restores consistent interior lighting for visibility
• Replaces sockets with heat damage, cracks, or worn contacts
• Symptoms: light stays off with a good bulb, flickers intermittently, or the bulb feels loose

• Disconnect power before servicing and allow the area to cool
• Remove the lens/cover and bulb; release the socket (tabs or screws) to remove
• Transfer wires one at a time to the new socket; ensure tight, correct connections
• Use only the bulb type and wattage specified for your model; test before reassembly

The Motor Wiring Harness is an OEM replacement part for LG washing machines. It is responsible for supplying power from the washer control board to the motor and related components. The wiring harness conducts electrical current, allowing for the operation of the pump, motor, and other vital systems. 

Causes of a bad motor wiring harness can include damage due to repetitive use and wear over long periods of time, exposure to moisture, impact or abrasion damage, or faulty insulation leading to electrical shorts.

Symptoms of a bad motor wiring harness include: 

• The washer failing to start or functioning intermittently
• Strange noises coming from the motor or other electrical components
• Slow or ineffective spinning or agitation  
• Error codes displayed on the control panel

This OEM LG part is also compatible with Sears/Kenmore washing machines. 

This moisture sensor connector assembly links the dryer's sensor bars to the control to monitor fabric dryness and adjust cycle time. Replacing a damaged or loose harness restores consistent Auto Dry operation.

• Connects the moisture sensor bars to the main control for Auto Dry feedback
• Transmits the low-voltage signal used to determine when clothes are dry
• Failure may cause Auto Dry to end too soon, run too long, or deliver inconsistent results
• Typical issues include broken wires, loose/corroded terminals, or a heat-damaged plug

• Disconnect power; if gas, shut off gas supply before service
• Access the moisture sensor area at the front/lint housing
• Match routing and clips, seat terminals fully on the sensor tabs, and secure the connector
• Keep wiring clear of sharp edges and moving parts; reassemble and test a Sensor Dry cycle

This motor wire harness links the washer's drive motor to the main control, carrying power and signal connections so the drum can start and regulate spin/tumble. Replacing a damaged harness restores reliable motor operation and helps prevent intermittent faults.

• Carries power and control signals between the main PCB and the drive motor
• Ensures secure, keyed connections at the motor and control board
• Drum won't spin or tumble, or stops mid-cycle
• Intermittent motor operation, humming, or "LE" motor error on some models
• Visible heat damage, broken wires, or loose/burned connectors

• Disconnect power before servicing; allow any capacitors on the control to discharge
• Access the harness by removing the rear or top panel per your model's service information
• Photograph routing and reuse all clips/ties; keep wiring clear of the rotor/drum and sharp edges
• Seat connectors fully (keyed plugs only fit one way); do not force, and secure all strain reliefs

This is a motor harness intended for use with washing machines. The motor harness is a wiring component that's attached to the washing machine's motor and is used to conduct electricity between the motor and the PCB. Wear and tear, damage, or other issues can arise with the motor harness over time. When there is a malfunction or failure with this component, a replacement part is necessary to continue the appliance's efficient and safe use.Signs that something has gone wrong with the washing machine's motor harness include intermittent operations or a device that won't run at all. Replacing the motor harness is a relatively easy task. Disconnect the appliance from power and wear work gloves for safety. Ensure all connections between the motor and motor harness are secure before plugging the washing machine back into to avoid the motor's accidental activation.This motor harness is an authentic OEM replacement part. It is sold as an individual unit. The motor harness is made of high-quality, durable materials. It comes sourced directly from the manufacturer to ensure compatibility. The motor harness can be installed in various models of washing machines. It fits correctly into appliances produced by Kenmore and LG.

This Power Cord Assembly restores a secure, grounded connection from your wall outlet to the washer's internal power circuit. Replace a frayed or failed cord to resolve no-power issues and maintain safe operation. What it does:

• Delivers AC power from the wall outlet to the washer's internal power circuit (line filter/control)
• Provides a proper equipment ground path for the cabinet
• Replaces damaged or overheated cords that can cause power loss
• Common symptoms include: washer has no power, won't start, intermittent power when the cord is moved, or visible cord/plug damage

• 1 power cord assembly

• Disconnect the washer from power before servicing and verify the outlet/breaker are in good condition
• Access cord connections by removing the rear or top panel per your model's service information
• Note original routing and strain relief; reinstall clips/guides the same way to prevent chafing
• Secure the ground connection and fully seat all terminals; keep wiring clear of sharp edges before testing

This multi-wire harness connects the washer's control system to multiple components. Replacing a damaged harness restores reliable power and signal routing and can help resolve intermittent operation, error codes, or no-spin/no-drain conditions caused by broken or burnt wires.

• Distributes electrical power and control signals between the PCB and components such as the motor, drain pump, inlet valves, sensors, and door lock
• Provides factory-terminated, keyed connectors and correct routing paths for secure, plug-in connections
• Typical failure symptoms: won't start or intermittent operation, component-related error codes, no spin/drain/fill, or visible heat damage to wires/connectors
• Using the exact harness maintains proper connector types and lengths for your appliance's design

• Disconnect power and turn off water supply before servicing
• Access the harness by removing panels as needed; take photos to document original routing and connections
• Transfer plugs one at a time; match keyed connectors and do not force them into place
• Secure the new harness under factory clips and away from sharp edges or moving parts; test operation before reassembly

This wire harness routes power and signals between the washer's control and multiple components. Replace a damaged harness to restore dependable operation when wiring is cut, brittle, or connectors are heat-damaged or corroded.

• Distributes electrical power and communication between the control board and components such as the motor, pump, valves, door lock, and sensors
• Maintains safe, reliable connections when insulation and terminals are intact
• Typical failure signs: intermittent operation, no start, specific loads not working (pump/motor/valves), or error codes traced to wiring faults
• Visible damage like chafed wires, broken connector locks, or burned/corroded terminals indicates replacement

• Disconnect power and turn off water supply before servicing; wear cut-resistant gloves
• Photograph and label connectors; move one plug at a time from old to new to avoid miswiring
• Route along original clips, channels, and grommets; keep wiring clear of sharp edges and moving parts
• Ensure all connectors are fully seated; test operation before final reassembly

This controller assembly is the main electronic control board that manages your appliance's cycles and user interface, restoring normal control when the original board fails. It replaces a faulty control module to help the unit operate reliably. What it does:

• Controls timing, cycles, and functions per user commands and sensor inputs
• Replaces malfunctioning or unresponsive control electronics that cause erratic operation
• Can resolve symptoms such as no power to controls, unresponsive buttons, or incorrect cycle behavior
• Works with existing wiring harnesses and display components when compatible

• Disconnect power before beginning work to prevent shock or damage
• Verify connector locations and orientation before removing the old board
• Handle the board by edges and avoid contact with circuitry to prevent static damage

This single wiring harness connects appliance components to deliver power and signals, restoring reliable electrical continuity and component communication. Use when a damaged or corroded harness causes intermittent operation or complete failure of the connected part. What it does:

• Routes power and signal connections between components to ensure proper operation
• Replaces broken, frayed, or burned wiring that can cause intermittent power or component failure
• Helps stop symptoms like no power to a component, erratic behavior, or intermittent operation
• Maintains correct connector fit to prevent loose connections and arcing

• One single wiring harness as shown

• Disconnect power before servicing to avoid shock or short circuits
• Match connector shapes and terminal positions; do not force connectors
• Inspect mating connectors and terminals for damage or corrosion before installation

This is a replacement single electrical harness that restores the factory wiring connection between components. It provides a like-for-like connection to help return affected functions to normal operation when wiring is damaged. What it does:

• Carries electrical signals/power between components and the appliance control circuits
• Replaces frayed, melted, or broken wiring that can cause intermittent or complete function failure
• Commonly used when a component has no power, a circuit is open, or functions stop responding
• Helps eliminate loose connector issues that cause intermittent operation or error codes

• One (1) single electrical harness (part 6877ER3003C)

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Match connector shapes and pin counts; do not force connectors—verify secure seating
• Route and secure the harness per factory paths and clips to prevent chafing or heat exposure
• If you see melted connectors, burned insulation, or repeated failures,

This harness joint is a wiring connector that links two sections of an appliance wiring harness, restoring electrical continuity and reliable signal/power transfer. Use it to replace a damaged, loose, or corroded harness connection. What it does:

• Joins wiring harnesses so power and control signals pass between components
• Restores intermittent or lost electrical connections caused by broken or corroded terminals
• Helps eliminate symptoms like no power to a module, intermittent operation, or communication failures
• Maintains proper routing and strain relief where harness sections meet

• Disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Match connector shape and terminal arrangement before installation; secure firmly until it clicks or seats
• Avoid forcing pins; inspect adjacent wires and insulation for damage and replace if needed

This genuine power cord assembly restores safe electrical connection to your appliance by replacing a damaged or worn power lead. Durable wiring and molded connectors help ensure a reliable feed for normal operation. What it does:

• Replaces a faulty or damaged power lead to restore power flow to the appliance
• Provides a secure, molded connection between the appliance and household power
• Can stop symptoms like no power, intermittent power loss, or tripped breakers caused by a compromised cord
• Helps eliminate loose or exposed wiring that can cause arcing or electrical smell

• Disconnect appliance from power before inspecting or replacing the cord.
• Match connector orientation and seating; secure strain relief and routing per appliance harness.
• Inspect mounting points and strain relief; do not use if connectors or wiring show damage.

This power cord assembly provides a factory-style replacement to restore safe power delivery to your appliance. It gives a direct-fit connection to the unit's power inlet for reliable operation and easier repairs. What it does

• Replaces a damaged or frayed power cord to restore electrical connection to the appliance
• Stops intermittent power, burning smell, or visible damage caused by a faulty cord
• Ensures a proper fit and strain relief for the appliance's power inlet
• Helps prevent arcing or loose connections when installed correctly

• One replacement power cord assembly as shown

• Disconnect all power to the appliance before starting any repair
• Tighten all terminal connections securely and replace any damaged fasteners or strain-relief clips

This multi wire harness connects key electrical components to the appliance control system, restoring proper power and signal routing for affected circuits. Designed as a direct OEM replacement to repair wiring-related failures. What it does:

• Routes power and control signals between the main control board and multiple components
• Replaces damaged or burned wiring that can cause intermittent or complete loss of function
• Helps resolve symptoms such as control board errors, unresponsive cycles, or components not powering on
• Maintains factory connector fit and pin layout for reliable electrical connections

• One multi wire harness

• Disconnect power to the appliance before servicing to avoid shock or damage
• Match connectors and pin orientation to the original harness before disconnecting; take photos if needed
• Inspect connectors and mating terminals for corrosion or damage and replace if required