Cable Or Retainer

The Dishwasher Door Cable Connector Assembly is an OEM replacement part for LG dishwasher. The cable connector assembly works with the door cable to properly guide and support the door as it moves through the full range of opening and closing motions. 

Causes of a bad door cable connector can include wear and tear over time resulting in cracks, loose connections, or broken or damaged connectors that no longer securely attach the cable. 

Symptoms of a bad door cable connector include:

• The door not properly aligning when closed 
• Difficulty opening or closing the door smoothly
• Noisy operation or rattling sounds from the door area
• The door not latching securely in place

This OEM LG part is also compatible with select Sears/Kenmore brand models.

This molded wire tie standoff provides a secure anchor point for a cable tie to hold wiring and harnesses away from moving parts and hot or sharp surfaces, helping reduce wear and electrical risk. Fits common HVAC and appliance wiring panels. What it does:

• Anchors wire ties to the appliance cabinet or chassis so harnesses stay routed and secured
• Prevents wires from rubbing on sharp edges, hot components or moving parts
• Helps stop intermittent electrical issues from loose or vibrating connections
• Reduces noise from loose wiring that can vibrate during operation

• One wire tie standoff

• Disconnect power before servicing the appliance to avoid shock or damage
• Mount in the original standoff hole or approved panel location; secure a cable tie through the top loop to hold the harness
• Use the correct fastener or snap method for your model—do not force or overtighten
• If routing or attaching multiple wires, verify clearance from heating elements and moving parts

This retainer is a small mounting clip that secures internal appliance components, keeping parts aligned and preventing vibration or rattling. Replacing a worn or broken retainer restores proper fit and helps reduce noise and movement. What it does:

• Secures a specific internal component to its mounting point to maintain proper alignment
• Keeps parts from shifting or vibrating during operation
• Helps prevent intermittent noise caused by loose fittings
• Supports reliable operation by holding components in the correct position

• One retainer clip

• Disconnect power to the appliance before beginning any work
• Inspect the surrounding mounting area and matching mating tabs for damage before installing
• Install the retainer by aligning it to the mating slots and snapping or fastening it into place; use gentle pressure to avoid breakage
• If other mounting hardware or adjacent parts are damaged, replace them as well for a secure fit

This plastic flat drive belt transmits motion between components to enable proper operation of the appliance. It replaces a worn or broken belt to restore consistent movement and reduce slipping. What it does

• Transfers rotational force from a motor or gearbox to driven parts to power operation
• Restores normal movement when a belt is cracked, stretched, or broken
• Helps eliminate slipping, uneven operation, or intermittent cycles caused by belt failure
• Used where a molded or flat plastic belt is specified instead of a rubber V-belt

• One replacement plastic flat drive belt as shown

• Install only when the appliance is unplugged or the circuit is powered off to avoid shock or injury
• Inspect pulleys, idlers, and related parts for wear and replace if damaged to prevent premature belt failure

This inside drain hose directs defrost and condensation water from the freezer evaporator to the refrigerator drain system, helping prevent pooling and ice buildup. Replaces a worn, clogged, or cracked evaporator drain hose to restore normal drainage. What it does:

• Channels defrost and condensation water away from the evaporator area to the drain pan or tube
• Helps prevent water pooling, ice formation, and water leaks inside the freezer compartment
• Restores proper drainage when the original hose is cracked, split, or clogged
• Works with the appliance's internal drain fittings and clamp connections

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access requires removing interior panels or the evaporator cover; handle evaporator fins and sensors carefully
• Check and clear drain inlet and drain tube of debris when replacing the hose
• Use proper clamps or fasteners and avoid kinks or tight bends that restrict water flow