Cooktop Touch Pad

Replace the control panel to restore a clean, secure interface for selecting settings and protecting the controls. Ideal when the original panel is cracked, dented, loose, or its graphics are worn and hard to read.

• Provides the fascia that houses and aligns the keypad/display or control knobs
• Shields internal components from heat, spills, and impacts
• Restores proper button alignment and the appearance of the front console
• Common symptoms: cracked or broken panel, stripped or missing mounting tabs, peeling/illegible labels, loose or rattling console

• Disconnect power at the breaker before servicing
• Remove door/knobs/trim as needed; support the console while removing mounting screws
• Transfer any attached controls and hardware from the old panel to the new panel
• Handle sharp edges and do not overtighten fasteners to avoid damage

This overlay is the graphic label for the appliance's control panel. It restores clear button legends and a clean finish, replacing a worn, peeling, or damaged original so the controls are easy to read and use.

• Provides printed button labels and indicator marks for the user interface
• Helps shield the underlying touchpad/control board area from everyday wear
• Replace if text has worn off, film is peeling or bubbling, edges are cracked, or surface is sticky/discolored
• Common after replacing a touchpad/control panel, when graphics must match the new assembly

• Disconnect power before servicing to prevent accidental operation or shock
• Remove the control panel and old overlay; clean and dry the mounting surface
• Align the new overlay with buttons/indicators and apply evenly without wrinkles
• Reassemble and test the controls for proper operation

The membrane switch is the low-profile keypad behind your microwave's control panel. It registers button presses so you can select settings and start cooking. Replace it if keys stop responding or require excessive pressure.

• Converts keypad presses into signals for the electronic control
• Enables selection of power levels, cook times, and options
• Common symptoms: some or all keys don't work, intermittent response, must press very hard
• If the unit won't start/stop from the keypad, the membrane switch may be faulty

• Disconnect power at the breaker before servicing
• Remove the control panel to access the keypad; note ribbon orientation and routing
• Handle the flexible ribbon carefully—don't crease it—and fully seat/lock the connector

This faceplate is the front cover for the control panel. It restores a finished look and helps protect and support the control assembly so the controls align and operate correctly.

• Covers and shields the control assembly from everyday use
• Provides secure mounting and proper alignment for controls
• Replace if cracked, warped, or if mounting tabs are broken
• Common signs include a loose or missing cover, rattling panel, or misaligned controls

• Disconnect power at the breaker before servicing
• Remove screws/retainers to lift the control panel; support the board and wiring
• Transfer any existing brackets or clips to the new faceplate as needed
• Reinstall, restore power, and test

This Whirlpool touchpad and control panel is intended for use with wall ovens. The control panel and touchpad provide users with the ability to control the oven's functions. The touchpad can wear out through normal, everyday use over time. The panel itself, although made from stainless steel and very durable, can also begin to wear if not properly cleaned and maintained.Signs that the touchpad might need to be replaced include difficulty pressing the buttons and operating the oven. If the overlay on the display is difficult to read, or if the metal is corroding, it should also be replaced. Before replacing this part, first turn off the breaker to the oven. Then, remove the two screws at the top of the display and pull outward. Remove the control board from the inside and install it in the new panel, then install the panel.This is a genuine OEM part, sold individually. It fits Maytag wall ovens only.

This control panel assembly replaces the appliance's user interface. Installing a new panel restores reliable button response and a clean, factory look so you can select settings, time, and options with confidence.

• Provides the button/touchpad area and display window you use to operate the appliance
• Sends key presses through its ribbon connector to the main control
• Common symptoms: unresponsive or intermittent keys, stuck/beeping keypad, or a cracked/worn panel face
• Restores proper console alignment and secure mounting

• Disconnect power at the breaker before servicing
• Remove trim/console screws; support the panel and transfer any clips, screws, or attached components from the old assembly as required by your model
• Handle flat ribbon cables by their connectors; avoid creasing and ensure they are fully seated/locked
• Test all keys and functions before final reassembly

This is a factory parts kit used to service and restore proper operation on compatible appliances. It replaces worn, damaged, or missing small components so assemblies fit correctly and operate as designed. What it does:

• Provides the exact small parts specified by the manufacturer for the application
• Restores proper fit and function where original pieces are worn, damaged, or missing
• Helps eliminate looseness, rattling, misalignment, or poor operation caused by incomplete hardware
• Built to original dimensions and materials for reliable performance

• One parts assembly kit

• Disconnect power and, if applicable, shut off gas/water before servicing
• Follow your model's service manual to identify part locations and orientation
• Use proper tools; handle sharp edges and small fasteners with care
• Test operation after reassembly and verify there are no leaks, rubbing, or loose hardware

Color: Black

This adhesive faceplate restores the labels and graphics on your oven's electronic control. Replace a faded, bubbled, or peeling overlay so settings and keys are easy to see again for safe, accurate operation.

• Provides printed button labels and display markings for the electronic oven control
• Replaces overlays worn by heat, cleaning chemicals, and normal use
• Common symptoms: faded or unreadable text, bubbling, lifted corners, sticky residue
• Note: Does not resolve unresponsive keys—typically indicates a keypad/touch panel or control issue

• Disconnect power at the breaker before servicing
• Remove trim as needed; gently warm and peel off the old overlay; clean all adhesive residue
• Dry-fit to alignment; peel liner and apply from one edge, smoothing to avoid bubbles
• Press firmly around display and key openings; allow adhesive to set before reassembly

This is a Whirlpool range control panel. It houses the display, user interface buttons, and has space for temperature control knobs. With extended use, the buttons on a control panel may wear out or stop responding to user input.Before installing this part, be sure to cut power to the appliance and allow it to cool completely. The stove may need to be pulled away from the wall to access the screws holding the old control panel in place. Remove the screws from each side of the old control panel to disconnect it, then carefully remove any boards or other components installed within the panel. Once it has been completely removed, the new control panel can be installed in its place.This is a genuine OEM part compatible with ranges manufactured by Whirlpool brands, including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product is just the panel and contains no additional parts or hardware.

This control panel overlay is the thin faceplate that mounts over the oven/range electronic control. It restores clear, readable button labels and a clean, factory look so you can select settings confidently.

• Provides printed labels/icons for modes, temperature, timers, and features on the electronic control (ERC)
• Covers the control face for a finished appearance
• Replace when graphics are faded, cracked, bubbled, or peeling
• Helps prevent confusion from missing or unreadable labels

• Disconnect power at the breaker before servicing
• Remove the backguard/control panel to access the electronic control
• Carefully remove the old overlay, clean the surface, and align the new overlay with the display window and button locations; apply even pressure to seat it
• Reassemble, restore power, and verify all functions align with the printed labels

The Overlay is an OEM part for Frigidaire ranges. The overlay protects the touch controls from accidental scratches, spills, and other damage while maintaining tactile button functionality.

Causes of a bad overlay include scratched or bubbled surfaces from cleaning chemicals or improper cleaning methods. Peeling or partial removal of the overlay layers can also occur from repeated use over time or accidental impact.

Symptoms of a bad overlay include:

• Unresponsive or intermittent touch controls
• Visible scratches, cracks, or chips in the overlay surface
• Peeling or lifting of the edge seals
• Discolored or stained appearance

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a control panel overlay for the electronic oven control on select ranges and wall ovens. It restores clear, readable button labels and refreshes the panel appearance while shielding the control face from everyday wear.

• Provides printed legends/icons for clock, timer, and oven functions
• Adheres to the EOC face to protect it from splashes and cleaning abrasion
• Use when the original overlay is faded, peeling, bubbled, cracked, or illegible
• Model-specific layout ensures the correct key positions and markings

• Disconnect power to the appliance before beginning any disassembly
• Remove the control panel/trim to access the old overlay; retain all hardware
• Carefully peel off the old overlay and clean residual adhesive; allow the surface to dry completely
• Align the new overlay with the display and key openings and apply evenly to avoid bubbles

This is the graphic control panel overlay for the oven/range user interface. It restores legible labels and a clean appearance for touchpad buttons, helping you see and select functions accurately when the original film is worn, bubbled, or damaged. What it does

• Adheres to the control panel/touchpad to provide printed button labels and icons
• Protects the underlying keypad from spills and cleaning wear
• Helps resolve faded, peeling, or unreadable control markings
• Can improve button feel and responsiveness when the old overlay is lifting
• Restores a finished, factory look to the control panel

• One control panel graphic overlay

• Disconnect power to the appliance before starting
• Clean and dry the control panel surface thoroughly; remove all adhesive residue
• Align carefully before applying—once set, adhesive may not reposition cleanly
• Press firmly and evenly to ensure full adhesion and avoid bubbles

The Overlay is an OEM part for Frigidaire ranges. It is a cosmetic component that covers and protects the control panel of the range. With a scratch-resistant surface, the overlay shields control buttons and displays from wear and spills in the kitchen. 

Symptoms of a bad overlay include:  

• Cracks, peels, or missing pieces in the overlay surface
• Faded or discolored graphics that are difficult to read  
• Exposed wiring or components under a broken overlay

Causes can be normal wear and tear over time, exposure to heat from the nearby cooktop, or damage from impacts or sharp objects.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a Whirlpool range control panel assembly. It houses the display, user interface buttons, and has space for temperature control knobs. With extended use, the buttons on a control panel may wear out or stop responding to user input.Before installing this part, be sure to cut power to the appliance and allow it to cool completely. The stove may need to be pulled away from the wall to access the screws holding the old control panel in place. Remove the screws from each side of the old control panel to disconnect it, then carefully remove any boards or other components installed within the panel. Once it has been completely removed, the new control panel can be installed in its place.This is a genuine OEM part compatible with ranges manufactured by Jenn-Air, but may also work with other Whirlpool brands, including Maytag, KitchenAid, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product is just the panel and contains no additional parts or hardware.