Dishwasher Dispenser Parts

• Will not dispense detergent

I bought a replacement part and changed it out. Read more

Replaced sump because the seal is not sold separately. You will need a skinny clamp after cutting the original swaged clamp off. Also Had to replace the cover as its seal is not sold separately either. Used dish soap on seals during assembly. Read more

Although I ordered the latch, lever and a new cup and replace the original pieces the dispenser still did not close. On further inspection it turned out to be a small spring that had fallen out of place. Once the spring was reconnected the dispensing cover worked fine. I'm still happy that I replaced the entire assembly with new parts regardless. Discovering the loose spring took the most time. Read more

Took cover completely off and tried putting back, could not match up left screw with available screw hole. Tried many different configurations and sequences to make this happen. watched a video on changing the front panel, the door in it had four screws, mine 2, no help there. Searched on the hyperextending issue, found an article about dogs and kids [had both here] climbing on the door and to check the springs and linkages. Linkages intact both sides, R [opposite] side spring very stretched.... Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

We ordered the dispenser cover kit. the problem was with the spring. followed your "how to" video and it was a quick and easy fix! Read more

I did not see the old ones fall out, so I was not sure the exact product placement within the rail, which was frustrating, to say the least. For the next person's benefit....these slide into the MIDDLE of the rail that is attached to both sides of the dishwasher. Not the front, not the back, but the middle! Steps to fix: 1) Order 2 of these Roller Bearing Cage. 2) Order 4 of WD12X10304 (AP4484666) end caps!! Unless you have brand new ones already, you will need them for sure and they are... Read more

I watched the video on your site and it showed step by step how to replace the spring. Excellent shipping time. Good customer service on chat forum. Read more

This was a pretty easy fix. Removed the screws around the perimeter of the inside cover of the door and pressed the outer door cover upward to release it from slots retaining it. There are four wires to remove (2 for the detergent door release and 2 for the rinse agent release). Removed the 6 screws retaining the dispenser assembly and inserted the new one. Reassembly is simply in reverse order. Problem solved for less than the cost of a service technician's call! Read more

Replaced dispenser Read more

Started with a YouTube video, then this site. Between the two, fixed in about a half an hour. Read more

I found a video on YouTube showing the exact repair sequence. Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

• Will not dispense detergent

I ordered a new vario motor and a soap dispenser. I turned off the water and the breaker, disconnected the water line and the power at the front base of the unit, disconnected the drain hose from the garbage dispenser, and pulled out the dishwasher and laid it on a blanket on its face. I unscrewed and removed the plainly visible vario motor on the bottom of the machine and removed the cam from the shaft. I then used a needle nose plier to carefully turn the D-shaft on the new motor to exactly... Read more

The cover was easy to remove with 3 star head screws. I entered my model number on AppliancePartsPros.com dreading the cost I was about the encounter. However, the parts were very cheap, in stock, and shipped within an hour of my order. I had a question about the tracking number and received an email back in less than an hour. The cost for both parts and standard shipping was under $30. Once I received the parts, the new cover was installed, the rest of the assembly was put back back... Read more

Repair parts arrived super fast. Installed the new parts according to the supplied instructions. All went well. It took over 2 hours because the unit had to be removed after the water and power were disconnected and then the initial problem diagnosed (motor brushes worn beyond service limits). The removal of the spray bar tower assembly was a challenge until it was discovered that the tower unscrews in a CW direction from the bar that then allowed access to the attachment screw that holds that... Read more